Parker Hi-drive Quick Installation Manual

quick installation guide Hi-drive Page 2 of 12 IMPORTANT INFORMATION The product Hi-drive, described in this handbook, doesn’t contain accessible parts to the customer, to open it or to try to approach the inner components could cause an irreparable fault. Some internal circuits are subject to voltages that could create serious hazards for people and even be lethal. It is prohibited to approach and/or to violate ...

quick installation guide Hi-drive Page 3 of 12 1.1 Hardware specifications Description Symbol UdM Type of drive Hi-Drive type 2 5 8 16 25 POWER Mains supply: three-phase or single-phase or D.C. Three-phase rated voltage Vmains V~ 200 – 10% � 480 +10% Single-phase rated voltage Vmains V~ 200 – 10% � 277 +10% D.C. Vdc V= 245 � 744 Frequency of the A.C. supply fmains Hz 50…60 ±5% Load installed for conti ...

quick installation guide Hi-drive Page 4 of 12 2.2 Assembly Do not install in hazardous environments. The rear supporting plate features special reamed holes (see illustration). • FIT IN VERTICAL POSITION (power terminal board at top). • To ensure drive cooling, leave a free space above, below and in front of at least 100 mm. The illustration shows how hot air cooling must be done in an external environment, t ...

quick installation guide Hi-drive Page 5 of 12 3 WIRING CONNECTIONS • Wire up the panel/drive/motor in accordance with the instructions in the operator's manual and applicable safety regulations. In case of any doubts, contact our After-Sales Service. • Check the correct dimensioning of the drive/motor. Compare the rated voltages and currents. • Make sure the maximum power voltage to terminals L1, L2, L3 doe ...

quick installation guide Hi-drive Page 6 of 12 3.3 Connector layout (*) The yellow and green LEDs are active if, when the drive supply is connected (24Vdc), the drive electronics is operating. The red LED, called “STATUS” provides a series of information on the state of the converter: - off the converter is disabled without active alarms. - on the converter is enabled: the drive is in RUN mode - flashing with ...

quick installation guide Hi-drive Page 7 of 12 X5 : terminal connection 0VQ drive supply 15 1 – SR drive enabling +24V drive supply 16 2 + SR drive enabling 17 3 SC B 18 4 SC A 19 5 N.C. GND (DIGITAL) 20 6 0VA OUT 1 21 7 MON 2 OUT 0 22 8 MON 1 VCC (DIGITAL) 23 9 0VA GND IN 24 10 – AX IN 3 (ENCODER IN) 25 11 + AX IN 2 (ENCODER IN) 26 12 0VA IN 1 27 13 – REF IN 0 28 14 + REF X6 : “resolver” (DB9 female ...

quick installation guide Hi-drive Page 8 of 12 In the case of D.C. current supply, the maximum voltage must be 744V=. The connection terminals are in terminal board X1 between the terminals RP (positive) and RN (negative). Direct connection to D.C. mains (three-phase) Connection for D.C. current 6 MOTOR Before entering the motor data parameter Pr31 must be defined: write “0” for brushless motor (default) ...

quick installation guide Hi-drive Page 9 of 12 8 FEEDBACK ( FBK ) Types: -FBK A, resolver only (only read if also selected as speed loop feedback). -FBK B, with the Pr62, the following systems can be selected: FBK B Pr62 INPUT ON Encoder Sincos + EnDat interface 0 X7 Encoder Sincos 1 X7 Encoder Less Wiring (**) 2 X7 5V Line Driver 422 quadrature signals (incremental encoder) (**) 3 X7 5V Line Driver 422 frequenc ...

quick installation guide Hi-drive Page 10 of 12 10 FIRST CONVERTER START-UP The drive is supplied from the factory with default programming. Remember that the Hi-drive can control brushless synchronous or asynchronous motors. Before entering the motor data, programme Pr31: write “0” for brushless motor (default condition), “1” for asynchronous motor. At this point the mechanism must be set with the fundame ...

quick installation guide Hi-drive Page 11 of 12 12 Alarms Pr23 Alarm Remedies 0 No alarm 1 Overvoltage Check the three-phase power line. Check the braking line and braking resistance Check the application 2 Undervoltage Check the three-phase power line. 3 Overcurrent Check any mechanical impediments and correct motor size for required use. Check motor connections and any short-circuits between phase-phase and phas ...