PXM PX370 Operation & User’s Manual

1 Description...................................................................................................4 2 Safety conditions........................................................................................5 3 Connectors and control elements...........................................................6 4 Designation of displayed messages.......................................................6 5 Button features................ ...

operation. PXM Marek Żupnik sp.k. Podłęże 654 32-003 Podłęże BDO register number 000005972 tel. +48 12 385 83 06 mail: [email protected] www.pxm.pl Rev.1-2 28.11.2018 3 ...

for controlling 4 channels (R, G, B, W) directly with the DMX protocol. Wide range of power supply voltage and high current carrying capacity outputs permit a control of large quantities of LEDs. PX370 can be either controlled by DMX, and act independently. In this case, the user is offered a fully programmable scene and 18 pre – programmed sequences, which can also ...

7 – 24V; however, during its installation and use the following rules must be strictly observed: 1. The device may only be connected to 7 – 24V DC with current-carrying capacity compatible with technical data. 2. All the conductors should be protected against mechanical and thermal damage. 3. In the event of damaging any conductor, it should be replaced with a conducto ...

4 Designation of displayed messages DMX address of a device – a basic item in the MENU setting parameters for all channels simultaneously setting parameters for each channel individually inverting the meter display 180 degrees DMX address setting control method selection (RGBW, Lightness / Colour, etc.) no DMX signal response method selection Master / Slave mode settings Lightness / Colour control mode 6 DMX-512 input DM ...

RGBW control mode RGB Dimmer control mode RGBW Dimmer control mode HSL control mode – Hue / Saturation / Lightness effect control mode dynamic white mode all outputs at 100% all outputs off scene programme no. 17 DMX address settings for first channel Master mode on / off number of channels being sent in the Master mode white colour balance setting red balance green balance blue balance white balance white colour balance on / off program ...

green colour during scene programming blue colour during scene programming white colour during scene programming basic frequency of brightness control screen blanking memory error message restore default device settings menu 5 Button features escape – goes back to the previous MENU level or discards changes made previous – scrolls to the previous feature on the same MENU level or decreases the parameter's value n ...

1. Set the Adr function. 2. Use the “next” or “previous” buttons to set the selected DMX address. 3. Push the “enter” button to confirm choose. 7 Individual DMX address settings The PX370 module has an option that allows for changing individual settings. It enables assigning any DMX address to every output channel. The simplest example of implementation of this function is to control the lightness of one-color LEDs conne ...

The PX370 driver can operate in different control modes. Depending on the selected mode, the device takes up a different numbers of channels, possible modes: The HSL mode (Hue, Saturation, Lightness) operates on three channels, responsible for hue, saturation and lightness The 3bd mode (4-channel, 4-byte) allows for setting each colour individually: R (red), G (green), B (blue) and on the fourth channel the Dimmer function is impleme ...

white, by means of four DMX channels. The first DMX channel is responsible for colour temperature of the first group, and the other channel – for lightness of the group. Similarly, the third and the fourth DMX channels control the other group. The EFF mode – effects control – it is available on 8 DMX channels and allows to choose the right effect and parameters (description o ...

CHANNEL 1 RED CHANNEL 2 GREEN CHANNEL 3 BLUE CHANNEL 4 WHITE CHANNEL 5 MODE CHANNEL 6 SPEED CHANNEL 7 FADE CHANNEL 8 BRIGHTNESS - - - - <0–7> Program 1 x x x - - - - <8–15> Program 2 x x x - - - - <16–23> Program 3 x x x - - - - <24–31> Program 4 x x x - - - - <32–39> Program 5 x x x - - - - <40–47> Program 6 x x x - - - - <48–55> Program 7 x x x - - - - <56–63> Program 8 x x x - - - - <64–71> Progr ...

Channel 2 – green colour Channel 3 – blue colour Channel 4 – white colour Channel 5 – operating mode selection Channel 6 – speed settings (higher value – quicker changes) Channel 7 – fade settings (higher value – smoother transition) Channel 8 – lightness settings (higher value – stronger glow) sign "x” – possibility to control a given parameter of a selected mode sign "-” – no possibility to control a g ...

each program it is possible to set the speed (SPd) of the effects reproduction on range 0,1 – 99,9s and smoothness of change of steps (FAd) in range 0 – 100, where 0 is a step transition, and 100 completely smooth. Sc –self-programmed scene in which it possible to set values for RGB colors (rEd, Grn, bLu, HtE) in range 0 – 255 for each colour separately. Additionally can ...

The following tables show the values for each output channel (R, G, B, W) in programs from 1 up 18 (P01 – P18). The value 255 corresponds to the maximum lightness level on a given channel, 127 – 50% of power level, 0 – full channel blanking. P01 P02 P03 P04 P05 P06 P07 P08 P09 Step 1 R 255 0 0 0 255 255 0 0 255 G 0 0 0 0 0 0 255 255 0 B 0 255 0 0 0 0 255 0 0 W 0 0 255 0 255 0 0 0 255 Step 2 R 0 0 255 0 255 255 0 0 0 G 255 ...

The PX370 module has a built-in DMX-512 recei ...

very large installations without using an external controller. Con – turning on or turning oFF Master feature Chn – the number of DMX channels sent 11 White balance Sometimes, there can be problems with getting white colour on the RGBW series LEDs. This may be a result of using diodes with different technical parameters. For this reason, the PX370 module is equipped ...

bLG – value for the green colour (0 – 100) bLb – value for the blue colour (0 – 100) bLY – value for the white colour (0 – 100) bCn – turning on or turning oFF the white balance 12 Smooth The driver is equipped with a smooth option. Smooth feature allows for smooth changes in lightness and colour. When it is set to On the transition between successive DMX values sent to the lamp (e.g. corresponding ...

changes in the DMX signal; therefore, it is possible to disable this option. This can be done by checking the parameter and confirming the selection by pressing “enter”. 13 Light control frequency The Frq function allows for setting the basic control frequency for the LEDs. This function is extremely useful in applications for the television industry. By applying the "flicker free" ...

the flickering effects that are visible in video cameras. 14 Screen saving (screen blanking) The device is equipped with a feature that allows for turning off the backlight. This option is marked with the SCr sign. With this feature, the display is turned off after about 60s (if the keys of the device are not pressed). Of course, the device continues its operation without interferin ...