Procom ECON-A-4C Operating Instructions Manual

Text of Procom ECON-A-4C Operating Instructions Manual

2.0 Salient features, Protection & Supervision

3.0 Display/ Front Panel 4.0 Switches Description 5.0 LED Annunciations Description 6.0 Lamp Test 7.0 Digital Input 8.0 Analog Input 9.0 Digital Output 10.0 Modes of Operation 10.1 AMF Mode (ECON-A & ECON -A-4C) 10.1.1 Auto Mode 10.1.2 Semi Auto Mode 10.1.3 Manual Mode 10.2 Auto Stop Mode ( ECON-A & ECON - A-4C or ECON-S) 10.3 Manua

• 1.0 Introduction

Microprocessor based controller for DG Set which can be configured as both automatic or manual controller. ECON comes in various models to cater for varieties of requirements: • ECON-A-4C • ECON-A • ECON-S • ECON-M • ECON-A-4C: It is a AMF controller with 4 channel of analog measurement and can be site configured as ECON-A or ECON-S or ECON-M. • ECON-A: It is a AMF controller with 3 Analog channels and is site confi

Procom ECON-A-4C • 2.0 Salient Features, Protection and Supervision

• Mains Measurements ◦ 1 Phase/ 3 Phase Voltage ◦ 1 Phase/ 3 Phase Current ◦ Frequency ◦ PF, KW, KVA, • Generator Measurements ◦ 1 Phase / 3 Phase Voltage ◦ 1 Phase / 3 Phase Current ◦ Frequency ◦ PF, KW, KVA, KWH . ◦ Battery Voltage ◦ Water Temperature ◦ Oil Pressure ◦ Fuel Level ◦ RPM ◦ Run Hour ◦ Service Due Hour • Protection / Supervision Mains ◦ Un

◦ AMF Operation: 9 outputs (five fixed and three programmable) and one for

charging Alternator • Fault Data Recording: Last 64 fault with date and time stamping • Event Recording: Last 64 event with date and time stamping • Start Stop Recording: Last 100 records with date and time stamping • Password Protection: Three digit password protection for system settings. • Real Time Clock (RTC) • Communication: RS232, USB, Fully Isolated RS485(Op

Normal operation mode: In this mode, it is

used to change the parameters being displayed on LCD. Programming Mode: Next key is used to select the next parameter to be programmed. Increment /Start This key has dual function Programming Mode: It is used to increment the value of the parameters under programming. Manual mode: it is used to issue the crank/ start command to DG Decrement /Stop This key has d

Led lights up when ECON is in Semi Auto

Mains Voltage This symbol lights up continuously if Main is healthy else starts blinking. MCB LED turns on in case the mains breaker is switched on or else turned off GCB LED turns on in case the DG breaker is switched on or else turned off DG Voltage This indication glows continuously when the generator is running. Warning This LED blinks in case of a warni

Page - 7

• 8.0 Analog Input: ECON has 4 Analog Input ◦ Low Lube Oil Pressure Sensor ◦ High Water Temperature Sensor ◦ Low Fuel Level Sensor ◦ OIL Temperature (ECON-A-4C only ) • 9.0 Digital Output: ECON has 9 digital outputs : • Programmable output Three digital outputs can independently be configured for the any functions from the list below. ◦ Unit Healthy ◦ Load Warning ◦ Fuel Pump ◦ Heater/Choke

Inputs: Emergency, V-Belt, RWL,, LLOP Switch etc) and internal faults

(Measured Values faults: LLOP, HWT, Fuel, Over Load, voltage and frequency). On persistence of any fault for more than the programmed supervision delay,for that fault, generator is stopped, corresponding fault is announced & hooter is switched on. On restoration of healthy mains supply, continuously, for the programme duration the load is transferred to the mains and generator is st

• 10.2 MCCB Shunt trip or Auto Stop Mode (ECON-A , ECON -A-4C or

ECON-S) This mode is a mix of Manual and Auto mode. In this mode the engine is manually started but its shut down on the restoration of the mains. To make sure that the engine is not shut down on load and also to recool the engine before shutting it down it has provision to activate the shunt trip coil of MMCB before shutting it down it has provision to activate the shunt trip coil o

Procom ECON-A-4C Page - 10

To go to next menu press Start Switch the LCD shall display “Protection Parameter” To enter Protection Parameter setting mode press Next Switch. For any change in value, press Start switch and Stop switch. For next parameter, press Next Switch. To go to next menu press Start Switch the LCD shall display “Comm Rs485 Parameter”To enter Comm RS-485 Parameter setting mode press Next Switch. For any chang

• 12.0 Parameter Mode:

The following tables give the detailed descriptions. Please note that 20sec of inactivity will take the unit back in normal mode and all the changes done shall be cancelled. • 12.1 System Parameter Parameter Name on LCD & Icon Explanation of Parameter Factory Setting Setting Range Enter Password Systems setting are password protected. Password is a three digit number 123 0-999 System Config ECON provides complete flexi

Fuel Sensor Select the installed sensor for Fuel

Type A Type A, Sam-0, Sam-1, Electronics, Linear, 0-5V(0-100%), Disabled* HWT Sensor Select the installed sensor for HWT Type A Type A, Type B,M&M, MNEPL,VE, TMTL AIR 1C, TMTL AIR 3C, TMTL WATER HUAFANG, TATA, GC(VDO), GC(MURPHY), Disabled * Oil Temp. Sensor Select the installed sensor for Oil Temp. Type A Type A, Type B,M&M, MNEPL,VE, TMTL AIR 1C, TMTL AIR 3C, TMTL WATER HUAFANG, TATA, GC(VDO), GC(MURPHY

Procom ECON-A-4C These are three programmable

output which can be configured for any one function from the list None None Unit Healthy Load Warning Fuel Pump Heater / Choke Pull Solenoid Over Load KW The Power(KW) above which the over load fault monitoring will start. The timer for it is as described in 13. This fault is only enabled while the generator is running. On expiry of the timer the generator is stopped 40 1-9999 Over Current The curr

Procom ECON-A-4C This can be configured for one out

the listed below Parameters. HET Oil Level Oil Temperature Canopy Temperature HWT HWT Oil Level Oil Temperature, Canopy Temperature Digital Input 5# This can be configured for one out the listed below Parameters. Canopy door open Oil Level Oil Temperature Canopy Temperature Oil Temp. Oil Level Oil Temp., Canopy Temp. Digital Input 6# This can be configured for one out the listed below Parameters. Fire O

Page - 15

Fan High Current Maximum limit for fan current 2.0 0-3.5 Fan Low Current Minimum limit for fan current 0.2 0-3.5 Fan Current Delay This is the timer for fan current trip. 5 1-100 > > Digital input 4 polarity Normally open: Open contact is healthy. Normally close: Close contact is healthy. Normally open Normally closed Normally open Digital input 5 polarity # Normally open: Open contact is healthy. Normally close: Close cont

Page - 16

• 12.2 Generator Parameter Generator O/V Max. Permissible Generator voltage, above this the Generator voltage is treated unhealthy & the Generator is stopped on voltage fault. 270V 50-300V Generator U/V Min. permissible Generator voltage, below this the Generator voltage is treated unhealthy & the Generator is stopped on voltage fault. 180V 50-300V Gen Voltage Delay Duration for which generator Over/Under voltage conditi

Page - 17

Service Due Hr Time, in hours, for next service due warning. 250Hrs 10-999 Hrs Crank Cut Method Auto disconnects the crank command on detection of either voltage buildup/ voltage or oil pressure build up Voltage Only Voltage only Voltage or LLOP Pick Up KVA warning If the current level crosses this limit the contact is energized after the programmed supervision time 8 1-9999 KVA Reset KVA warning If the current level falls

Procom Controller Owners Instructions: