ATTO Technology 4500C Installation And Operation Manual

Text of ATTO Technology 4500C Installation And Operation Manual

ATTO Technology Inc.

ATTO FibreBridgeTM 4500C/R/D Installation and Operation Manual © 2003 ATTO Technology, Inc. All rights reserved. All brand or product names are trademarks of their respective holders. No part of this manual may be reproduced in any form or by any means without the express written permission of ATTO Technology, Inc. 10/03 Document Control Number: PRMA-02

1 Fibre Channel is a key technology for storage ................................1

Glossary 2 ATTO FibreBridge supports diverse SAN needs .............................3 2.1 ATTO FibreBridge 4500C characteristics ...........................5 Dimensions Environmental requirements Power Reset button Integration parameters cPCI Configuration Fibre Channel ports SCSI ports Ethernet port Serial port LED indicators Installing the FibreBridge 4500C 2.2 ATT

ATTO Technology 4500C 3.2 Handling multiple initiators ..................................................17

Single initiator Multiple Fibre Channel initiators Multiple FC & SCSI initiators 4 Accessing ATTO FibreBridge Services ............................................19 Access the ATTO FibreBridge through in-band SCSI over Fibre Channel Access the ATTO FibreBridge over the RS-232 port Configure the ATTO FibreBridge for a network over the Ethernet port Access the ATTO FibreBr

4.1.4 SCSI configuration commands ..............................29

ScsiInitID ScsiPortBusSpeed ScsiPortList ScsiPortReset ScsiPortResetOnStartup ScsiPortSelTimeout ScsiPortSyncTransfer ScsiPortTaggedQueuing ScsiPortWideTransfer ScsiTargets ScsiTermination SpeedWrite SpeedWriteDefault VirtualDriveResponse 4.1.5 Fibre Channel configuration commands ..............31 BootFibreDelay BootScan

ATTO Technology 4500C 4.1.8 Mapping commands ................................................36

AddressMap AutoMap BootFibreDelay BootScan BootScanPorts DispFcPortDB FcConnMode FcHard FcHardAddress FcPortFailure FcTargets FibreBridgeTargetLUN RouteChange RouteDisplay RouteOffline RouteOnline ScsiTargets ServicesLUN 4.2 FibreBridge menu text-based CLI interface ........................39 4.3 ATTO BridgeTools provides graphical interface ...............40 4.4 In-band CLI uses SCS

1 ATTO Technology FibreBridge 4500 Installation and Operation Manual

1 Fibre Channel is a key technology for storage Fibre Channel is a serial communications technology designed to transfer large amounts of data between a variety of hardware systems over long distances. It is a key technology for applications that require shared, high bandwidth access to storage. Fibre Channel provides a logical point-to-point serial channel for the transfer of data betwee

A port in the Fibre Channel fabric where a N_port may attach

FL-port A port in the Fibre Channel fabric where a NL_port may attach in an arbitrated loop hot swapping Components are removed and replaced while the unit is running, with power to either the component or a device connected to the unit. Not all components are hot swappable: please read installation and maintenance instructions carefully. initiator device A component which origi

ATTO Technology 4500C 3 ATTO Technology FibreBridge 4500 Installation and Operation Manual

2 ATTO FibreBridge supports diverse SAN needs The ATTO FibreBridgefamily of products provides a Fibre Channel-to-SCSI bridge available as a Compact PCI board, a stand alone enclosure that can be fitted for rackmount integration, or a desktop unit, depending on the model and your needs. The ATTO FibreBridge family of products share common configuration options and functions to provide the

ATTO FibreBridge and iPBridge availability matrix

FibreBridge 1180 FibreBridge 1290 FibreBridge 2300 FibreBridge 2350 FibreBridge 3300 FibreBridge 4500 iPBridge 2500 Configuration Board Desktop Board Board Rackmount Desktop Board Rack mount Board Rackmount Desktop Board Rackmount Desktop Fibre Channel ports 1 1 1 1 1 3 0 FC port number 0 0 0 0 0 0, 1, 2 FC interface DB9/SC SFP SFP SFP SFP SC Data transfer rate per sec. 1 Gigabit 2 Gigabit 2

5 ATTO Technology FibreBridge 4500 Installation and Operation Manual

2.1 ATTO FibreBridge 4500C characteristics The ATTO FibreBridge 4500C is a Fibre Channel to SCSI bridge with a CPCI interface for high throughput enterprise environments designed for mission-critical applications. The FibreBridge 4500C is a single embedded PCB with CPCI interface. Dimensions Width: 6.5 inches (170 mm) Length: 9.25 inches (230 mm) Height: .75 inches (19 mm). Environmental

The 10-pin serial port connector provides support for

remote monitoring and management through a command line interface, menu system or graphical interface (ATTO BridgeTools). In order to use the RS-232 port, you must ensure there is enough clearance above the face plate for the ribbon cable: do not place another card in the adjacent slot of the CPCI rack. Connect the 10 pin to DB9 converter cable to header P3 (in the same co

7 ATTO Technology FibreBridge 4500 Installation and Operation Manual

2.2 ATTO FibreBridge 4500R/D characteristics The ATTO FibreBridge 4500R/D is a Fibre Channel to SCSI bridge for high throughput enterprise environments designed for mission-critical applications which can be used on a desktop or in a rack. The FibreBridge 4500R/D is a versatile enclosure with attached feet for horizontal desktop use and mounting brackets to convert to standard 19-inch enc

Installing the FibreBridge 4500C/R/D

1 Physically place the FibreBridge 4500 where you want it, horizontally on a desktop or into a rack. 2 Connect the SCSI devices to the FibreBridge. (See Chapter 2.3) 3 Connect the FibreBridge to your SAN: attach short wave optical cables into the Fibre Channel ports on the FibreBridge. (See Chapter 2.4) 4 Connect to the management (services) port via the RS-232 serial port, Ethernet, or in-band SCSI o

9 ATTO Technology FibreBridge 4500 Installation and Operation Manual

2.3 Connecting SCSI devices to SCSI ports ATTO FibreBridge SCSI ports are used to connect SCSI storage devices into the Fibre Channel Storage Area Network (SAN). A FibreBridge may have the following types of SCSI ports: Ultra 2 (LVD) SCSI 80 MB/sec. max per bus Single Ended Ultra SCSI 40 MB/sec. max per bus High Voltage Differential (HVD) Ultra SCSI 40 MB/sec. max per bus The high voltage

Connecting the Fibre Channel ports

The Fibre Channel ports on the ATTO FibreBridge 4500C/R/D connect the bridge into either a Fabric or Arbitrated Loop. Fibre Channel technology offers a variety of cabling options including standard copper, equalized copper, multimode fiber optic, and single mode fiber optic. The FibreBridge 4500C/R/D uses an SC fiber optic cable connector. The type of cable to use varies depending upon the application, environment

ATTO Technology 4500C 11 ATTO Technology FibreBridge 4500 Installation and Operation Manual

3 Configuring the FibreBridge Configuration of the ATTO FibreBridge, also known as FibreBridge Services, is available via ATTO BridgeTools (a graphical user interface configuration manager), Command Line Interface (CLI) or a menu. FibreBridge Services includes displaying and modifying various attributes of FibreBridge operation, as well as the update of firmware. You may use a graphical

Software configures, manages

Exhibit 3-1 Post power up display. Type menu to enter the menu system; type help for a list of CLI commands ATTO FibreBridge 4500 (c) 2001 ATTO Technology, Incorporated. Firmware version 002R release date Feb 14 2001, 16:01:43 Build 002R Power-On Self-Test Completion Status: GOOD 64 Megabytes of RAM Installed. 3 1.0624 Gb/s Fibre Channel Interfaces. 4 LVD SCSI Interface Ports. Interface 0 World Wide Name = 20 00 00 10 86

ATTO Technology Network Hardware Owners Instructions: