Simu Hz 2 Programming Manual

1. Type of Slat: Height and Width 2. Total weight of shutter 3. Diameter of the tube Type of slat: Diameter of Tube: surface Total Weight of Shutter It is important to consider the total size of the product you plan to produce before choosing an operator, since these variables affect the weight of what an operator can lift. The fol ...

For Hz Type 5 Operators kg. lb. kg. lb. 9 20 9 20 18 40 18 40 27 60 27 60 36 80 36 80 45 100 45 100 55 120 55 120 64 140 64 140 73 160 73 160 82 180 82 180 91 200 91 200 100 220 100 220 109 240 109 240 118 260 118 260 127 280 127 280 136 300 136 300 145 320 145 320 155 340 155 340 164 360 164 360 173 380 173 380 Model Type Model Type 505 510 515 525 530 535 550 505 510 515 525 530 535 550 37(lbs.) 30(lbs.) 62(lbs.) 49(lbs.) 92(lbs.) 7 ...

For Hz Type 5 Operators kg. lb. 9 20 18 40 27 60 36 80 45 100 55 120 64 140 73 160 82 180 91 200 100 220 109 240 118 260 127 280 136 300 145 320 155 340 164 360 173 380 Model Type 505 510 515 525 530 535 550 25(lbs.) 41(lbs.) 62(lbs.) 103(lbs.) 123(lbs.) 143(lbs.) 205(lbs.) 78mm (3.0 inch) TUBE DIAMETER -The listed charts reflects the recommended 30% security factor that is used for most applications. -Shutters more than 9 feet high ...

motor for your lateral arm awning system. Important: T ...

Hz T5 Operators _ + + _ + _ _ + + _ _ + + _ _ + UP LIMIT ADJUSTMENT SCREW DOWN LIMIT ADJUSTMENT SCREW DOWN LIMIT ADJUSTMENT SCREW UP LIMIT ADJUSTMENT SCREW MATERIAL ROLLS DOWN ON SAME SIDE AS LIMITS MATERIAL ROLLS DOWN ON OPPOSITE SIDE FROM LIMITS 1) Identify which limit adjustment screw controls the up limit and which controls the down limit (see above diagrams). It is important to note that the arrows by the limit adjustment screw ...

Hz Type 5 DMI Operators UP LIMIT ADJUSTMENT SCREW DOWN LIMIT ADJUSTMENT SCREW DOWN LIMIT ADJUSTMENT SCREW UP LIMIT ADJUSTMENT SCREW MATERIAL ROLLS DOWN ON SAME SIDE AS LIMITS MATERIAL ROLLS DOWN ON OPPOSITE SIDE FROM LIMITS 1) Identify which limit adjustment screw controls the up limit and which controls the down limit (see above diagrams). It is important to note that the arrows by the limit adjustment screw refer to the tube's rot ...

Considerations / Installation OPERATOR WIRING CHART MOTOR CABLE POWER 120VAC BLACK WHITE GREEN HOT NEUTRAL GROUND BLACK WHITE GREEN HOT NEUTRAL GROUND POWER 120VAC 60Hz 1) FCC -This device complies with part 15 of the FCC Rules. Operating is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference ...

Multiple motors to one wireless switch. There is no limit to the amount of motors you can put to one switch. The only limitation is the range a transmitter can reach. This is approximately 70 feet through walls and up to 100 feet in open air. Single motor to multiple wireless switches. There is a limit of 12 transmitters of any type to one motor. Hz 2 Type 5 / DMI Operator Basic Rules and Scenarios R 10 ...

Example: By following the three basic rules illustrated on the front of this sheet, you can create almost any combination with the Hertz technology. Everything from individual switching and sub grouping to a master control can be accomplished without the use of external controls. The ability to parallel wire the Hertz operators makes it easy to wire. Simply supply power to the electric operator and progr ...

1) Setting Direction of Rotation The motor will be in “Factory Mode” right out of the box when power is connected. To prepare the motor for programming, press the transmitter up and down buttons simultaneously until motor jogs forward and back (example 1). Hold the transmitter within 10 feet of the motor and press the up button (example 2). If the motor rotates in the up direction, move t ...

number of motors you can program to one switch. The only limitation is the range a transmitter can reach. This is approximately 70 feet through walls and up to 100 feet in open air. 1) Setting Direction of Rotation The motor will be in “Factory Mode” right out of the box when power is connected. To prepare the motor for programming, press the transmitter up and down button ...

transmitters of any type to one motor. 2) Programming the 1st Transmitter After Hold the transmitter within 10 feet of the motor head (example 4). Press and hold the Program Button (about 1 second) until the motor jogs forward and back. Transmitter range will now be approximately 100 ft. 3) Programming additional transmitters the motor has memorized the first transmitter as ...

Instruction R 1)Pressing the up or down button on the transmitter will start the motor in the selected direction. 2)The motor can be stopped at any point by pressing the center (stop) button on the transmitter. 3)If the motor is stopped at the top limit, pressing the center button on the transmitter will move the motor to the one of the programmed intermediate stops. Pressing the center (stop) button when the motor ...

Interface Instruction R DESCRIPTION INSTALLATION 1) Mount the Dry Contact Interface as close to the motor(s) as possible and no more than 70 feet. Avoid mounting the receiver on metallic surfaces as this will reduce the range. If mounted outside, make sure to use the watertight strain reliefs and mount the box so the strain relief fittings face downward to avoid rain seepage. Install the unit in an accessible location as every 2 to ...

and Receivers R Switch Style & Programming Button Location Reference Description 6301066 6301070 6301071 6301090 White 6301091 Ivory 6301080 White 6301081 Ivory 6301075 6301072 Slim Single Channel Hand Held -Available in white Recessed Designer Single Channel -Available in white and ivory Hz Radio Receiver Motor Contro ...

Bracket Accessories U.S. Thread Item Reference Description Shade Bracket - U- Support for square 10mm motor mount 500073 - Attaches to wall bracket 800095 - Zinc Plated 510000 Shade Bracket - 50mm spacing / 4mm tapped holes - Zinc Plated 520038 Shade Bracket - Motor mount 10mm square pin - For Type 5 operators - Zinc Plated 520073 Awning Bracket - 48mm spacing / 6mm tapped ...

Bracket Accessories Item Reference Description Standard Bracket - 30mm spacing / counter sunk holes - Attaches to wall plate 850066 or 850067 - Zinc Plated 520076 Shade Bracket - 30mm spacing / 1/4” US Threaded holes - Attaches to wall bracket: 520210 - Gold Zinc Plated 252527 Shutter Bracket - Maxi side frame bracket 100x100mm - Requires side frame center pin to be removed - G ...

If a motor has two or more transmitters memorized it is possible to delete a transmitter from its memory. On the transmitter you want to keep, press and hold the Program Button (about 3 seconds) until the motor jogs forward and back. Press and hold the Program Button (about 1 second) on the transmitter you want to delete. When the motor jogs forward and back the transmitter is deleted. Note, if the tr ...

Hz2 PROGRAMMING INSTRUCTIONS 1) FCC -This device complies with part 15 of the FCC Rules. Operating is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. -Caution: Changes or modifications not expressly approved by the party responsible for compliance could v ...