Zxtech Tropox Operation & User’s Manual

Statement If the user manual cannot help you to solve the problem, please call our technology center about the solutions. We will update the content for the new functions without notice. Notice 1. Installation Environment  Keep away from the places for high-temperature, heat source and direct sunlight;  Keep away from water. When get wet, cut off the power immediately;  Avoid to use in damp environment, the reference range fo ...

affect the image quality (it is not the problem for the IP camera), also shorten the service life for the image sensor. 5. Keep away from laser when it is working, otherwise the image sensor can be damage. 6. If the equipment is not working properly, please contact the store or the service center, do not disassemble or modify the equipment in any way. (Problems caus ...

 Support 802.11b/g/n protocol, build-in WIFI module to perform wireless monitoring;  Support four regional motion detection and external alarm detector, achieve all-round protection on the spot;  Support level 3 user permissions Settings;  Support max. 32G micro SD card for storing the alarm video and pictures;  Built-in web server, use one port to send all the da ...

2. It will pop up a window as below; please choose the language you need, click“OK” 3. Click next. If you would like to select a different folder, click browser 4. Continually click “Next” until the following icon showed on “Start Menu” of your computer. ...

Note: The software automatically searches IP Camera within the LAN. It will display the IP address, name, MAC Address, Version, and Port. 6. There are three kinds of situation 1) Search to the device in the local area network (LAN). All devices will be listed as shown above, please double click IP address to enter login interface. . 2) Found no device in the Lan. Pls click Refresh ...

Gateway manually. Note: Part 2 is the current IP address, only part 1’s information can be revised. 7. Double click the camera’s IP address, your default browser will pop up a dialog, please enter default user name: admin and password: admin. Note: The first time you login the camera need to install the plugin, according to the ...

video like following picture. Attention： Because the system permission restriction of Windows 7/8/10 , after installing the video ActiveX, need to click the right mouse button to open the browser, select "Run as Administrator (A)" to launch the browser. 2.1.3 View video 1) Status bar 1. Multi-Device (Up to 4 cameras can be monitored at same time) 2. You can choose 1st st ...

3. PT control If the camera supports PT function, you can click up, down, left, right arrow to control the camera moving. 4. means start vertical, means stop 5. means start Horizontal, means stop 6. means turn on infrared Led light. means turn off infrared Led light 7. Snap/Record Click “Snap” button, to save the picture to the specified file. Click “Record” button to start ...

3.1 Video settings 3.1.1 Video settings CBR: constant bit rate, video encoder will work according to the fixed settings. VBR: Variable Bit Rate, video encoder will work variable to make image fluent, only refer to fixed settings. 1) Video format: If video has ripple, you can adjust to eliminate ripple here. 2) Video coding: Main profile or baseline; default main profile. 3) Bit rate: The image more smooth, but the higher the bandwidth. ...

Saturation, Contrast, Sharpness and Exposure to meet their visual user preferences. 2) Flip and mirror: set the picture upside down, left and right sides. 3) AE mode: automatically, indoor and outdoor exposure. 4) Night effect adjust 5) Restore the default value: click on the "default" button after restore image parameter values to the factory settings. 3.1.3 A ...

is good, but a larger bandwidth. If you choose to open the audio, then in the corresponding code stream will transmit audio information. 3.2 Network Settings 3.2.1 Basic network settings 1) HTTP port: IP address identifies the network device, the device can run multiple web applications, each network program and using network port to transmit data, so data transmission is ...

1. Connected by browsers 1) Step 1, Enable wireless 2) Step 2, Click “Search” 3) Step 3, Choose and Join your router at pop up new window 4) Step 4, Fill in user name and password of your router 5) Step 5, Click Apply 2. Connected via WPS 1) Please make sure your wireless router has WPS/QSS. 2) Press WPS/QSS button of the router two seconds and check if WPS signal light blinking. 3) Press the WPS button of came ...

A. Login the router and goes to the menu of Port Forwarding or Port Trigger (or named Virtue). B. Take Linksys brand router as an example, Login the router, and goes to Applications & Gaming->Single Port Forwarding. C. Create a new column by LAN IP address & HTTP Port No. of the camera within the router showed as below 2. Two ways of DDNS setting 1) After doing port forwarding ...

name+ http port to access the camera via internet. Take manufacturer’s DDNS a0001.ipcddns.com and http port 88 as an example, The correct accessing link would be http:// a0001.ipcddns.com:88 3.2.4 ONVIF IP Camera supports ONVIF can achieve compatibility with other manufacturers ONVIF products. 3.2.5 P2P P2P platform available parameters: server address, server port, and serial ...

3.3.1 Motion detection Please click “apply” after settings are done, and motion detection takes effect. The camera will trigger corresponding alarm when the detection area occur any change. 3.3.2 Alarm mode settings After camera triggers the alarm, it will store the capture pictures and videos according to your setting ways, for example, store in SD/TF, or upload to FTP, or email you, etc. Note: Please insert the SD/TF Card and tick ...

The device will trigger the alarm only during the scheduled time period, you can select the scheduled time according to your request. Note: Please make sure your system time is correct before you set the alarm time period. Please refer to chapter 3.5.1 to set system time. 3.4 Advanced Settings 3.4.1 User management There are 3 levels of user authorization 1) Admin: “administrator” has the highest authority. It can do any setti ...

Note: Please insert the TF / SD card under powered off state to set timing record. 3.4.4 Email The blanks must be filled completely and correctly. Any small mistakes will result in setting failed. Note: The password cannot use special character; otherwise the camera cannot identify it. ...

spaces for the video and keep FTP’s authority of write and creation open. NOTE: The password cannot use special character; otherwise the camera cannot identify it. 3.4.6 PT Cruise Laps: Control the laps of “Vertical” and “Horizontal”. Auto Center: Set direction of the cameras’ head when start 3.4.7 Multiple Devices You view multiple devices at same time ...

There are three options to set the time and date, including manual setting, sync with computer time, from network time server. 3.5.2 Initialize Choose “Backup setting data”, the camera will generate a file, user can save the setting on your computer. This feature is convenient for user to find the original settings of camera, do not need to set parameters again; “Upgrade firmware” is to upgra ...