Woodward easYgen-3000 Operation

Page 2/51 © Woodward WARNING Read this entire manual and all other publications pertaining to the work to be performed before install- ing, operating, or servicing this equipment. Practice all plant and safety instructions and precautions. Failure to follow instructions can cause personal injury and/or property damage. The engine, turbine, or other type of prime mover should be equipped with an overspeed (overte ...

© Woodward Page 3/51 Revision History Rev. Date Editor Changes NEW 06-11-23 TP Release A 07-06-29 TP Minor corrections and update to reflect the new functionality B 08-02-07 TP Minor corrections; easYgen-3100 description added; message IDs added Content CHAPTER 1. GENERAL INFORMATION.........................................................................................5 Document Overview....................... ...

Page 4/51 © Woodward Figures And Tables Figures Figure 2-1: Front panel and display........................................................................................................................................... 7 Figure 2-2: Screen - Level overview........................................................................................................................................ 24 Figure 3-1: Pos ...

© Woodward Page 5/51 Chapter 1. General Information Document Overview ≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡ Type English German easYgen-3000 Series easYgen-3000 - Installation 37223 GR37223 easYgen-3000 - Configuration 37224 GR37224 easYgen-3000 - Operation this manual � 37225 GR37225 easYgen-3000 - Application 37226 - easYgen-3000 - Interfaces 37383 - easYgen-3200 - Brief ...

Page 6/51 © Woodward Short Description ≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡ The easYgen-3000 Series generator set controllers provide the following functions: • Genset control • Engine, mains and generator protection • Engine data measurement - o oil pressure and temperature, coolant temperature, battery voltage, speed, service hours, etc. • Generator and mains data ...

© Woodward Page 7/51 Chapter 2. easYgen-3200 Navigation / Operation 3 1 2 3 4 13 9 10 11 14 5 6 7 8 12 Figure 2-1: Front panel and display Figure 2-1 illustrates the front panel/display of the easYgen-3200 with push buttons, LEDs and Liquid Crystal display (LC display). A short description of the front panel is given below. NOTE This push button is always active and will stop the engine when pressed, except the ...

Page 8/51 © Woodward Navigation ≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡ Individual display screens are listed in the following text. All softkeys, which are available in the individual screens are described with their function. Screen "Operating values - overview" / "Starting screen" [all application modes] This screen appears upon startup of the unit. Toggle between delta/wye ...

© Woodward Page 9/51 Screen "Alarm list" [all application modes] This screen appears after pressing the "Alarm" softkey in the start- ing screen. All alarm messages, which have not been acknowledged and cleared, are displayed. Each alarm is displayed with the alarm message and the date and time of the alarm occurred in the format yy-mon-dd hh:mm:ss.ss. Please note, that self-acknowledging alarm messages get a ne ...

Page 10/51 © Woodward Screen "Setpoints" [all application modes] This screen appears after pressing the "Setpoints" softkey in the "Next page" screen. The set point is displayed on the left and the actual value is displayed on the right half of the screen. The symbol indicates the mains power and indicates the generator power. The figures 1 or 2 indicate whether set point 1 or set point 2 is used in AUTOMATIC ...

© Woodward Page 11/51 Screen "Synchroscope" [all application modes] This screen appears after pressing the "Synchroscope" softkey in the "Next page" screen. Return to "Next page" screen. Synchroscope generator/busbar Display the generator / busbar synchroscope screen. Synchroscope busbar/mains Display the busbar / mains synchroscope screen. Screen "Synchroscope generator / busbar" [all application modes] This sc ...

Page 12/51 © Woodward Screen "Synchroscope busbar / mains" [all application modes] This screen appears after pressing the "Synchroscope Busbar / Mains" softkey in the "Synchroscope" screen. The square symbol indicates the actual phase angle between busbar and mains. The 12 o'clock position on the top means 0° and the 6 o'clock position on the bottom means 180°. The frequency and voltage differences are indicat ...

© Woodward Page 13/51 Screen "Sequencing" [all application modes] This screen appears after pressing the "Sequencing" softkey in the "Next page" screen. The sequencing screen shows all gensets par- ticipating in load sharing. The operation mode of each genset as well as the state of its GCB is shown on this screen. The symbol above the generator number indicates AUTOMATIC operating mode, indicates MANUAL, and ...

Page 14/51 © Woodward Screen "Counters and service" [all application modes] This screen appears after pressing the "Counters and service" soft- key in the "Next page" screen. Return to "Next page" screen. Scroll down to the energy counter display screen. Scroll up to the operating hours counter display screen. Change into AUTOMATIC operating mode. Change into MANUAL operating mode. Change into STOP operating mod ...

© Woodward Page 15/51 Screen "Measured values" [all application modes] This screen appears after pressing the "Measured values" softkey in the "Next page" screen. Return to the "Next page" screen. J1939 interface Display the J1939 interface indication screen. Analog inputs/outputs Display the analog inputs and outputs indication screen. Discrete inputs/outputs Display the discrete inputs and outputs indication s ...

Page 16/51 © Woodward Screen "Analog inputs/outputs" [all application modes] These screens appear after pressing the "Analog inputs/outputs" softkey in the "Measured values" screen. The analog inputs and outputs are displayed. The analog outputs are displayed as a per- centage of the selected hardware range, i.e. 50 % of a 0 to 20 mA output refer to 10 mA. Return to "Measured Values" screen. Scroll down to the " ...

© Woodward Page 17/51 Screen "Discrete inputs/outputs" [all application modes] This screen appears after pressing the "Discrete inputs/outputs" softkey in the "Measured values" screen. Discrete input and dis- crete output status are displayed. Return to "Measured Values" screen. Scroll down display screen to external discrete IOs. Scroll up display screen to internal discrete IOs. Change into AUTOMATIC operating ...

Page 18/51 © Woodward Screen "Generator" [all application modes] This screen appears after pressing the "Generator" softkey in the "Measured values" screen. All measured generator values are dis- played in this screen. Return to "Measured values" screen. Scroll down display screen to additional generator values. Scroll up display screen to main generator values. Reset the maximum value display. Change into AUTOM ...

© Woodward Page 19/51 Screen "Mains" [all application modes] This screen appears after pressing the "Mains" softkey in the "Measured values" screen. All measured generator values are dis- played in this screen. Return to "Measured values" screen. Scroll down display screen to additional mains values. Scroll up display screen to main mains values. Reset the maximum value display. Change into AUTOMATIC operating m ...

Page 20/51 © Woodward Screen "LogicsManager conditions" [all application modes] This screen appears after pressing the "LogicsManager conditions" softkey in the "Diagnostic" screen. You are able to display the con- ditions of all LogicsManager command variables, which are lo- cated in their respective groups. Return to "Diagnostic" screen. Scroll up one group / command variable. Scroll down one group / command v ...