Software House SWH-4100 Installation Manual

Technology 125 KHz and 13.56 MHz Reader Installation Guide Version H0 Part Number UM-090 May 2012

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Installation Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Installation Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Configuration Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Model SWH-4100 and SWH-4200 Technical Specifications . . . . . . . . . 16 FCC Digital Device Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 UL Standards Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 CE Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Cards at frequencies of both 125 kHz and 13.56 MHz. The reading capability includes, for Smart Cards, both unencrypted serial numbers and encrypted MIFARE® programmed sectors. Refer to Table 1 and Table 2 for a complete list of compatible standards and data. The SWH-4200 reader has a built-in keypad with 12 keys, including CMD/ ENTER and CE (Clear Entry). The reader outputs the PIN code in the 8-bit burst Wiegand. It also has the ability to read and verify the PIN on a Smart Card. This feature is enabled with the use of program cards. Please contact Software House® for more information on the PIN-on-Card function.

(125 KHZ) FORMATS SUPPORTED TABLE 1. Proximity (125 KHz) Formats Supported Proximity (125 KHz) Formats Supported As Shipped: Default Mode (On) HID® 26 Bit Yes HID® Corporate 1000 Yes HID® 36 Bit Wiegand Yes HID® 37 Bit Wiegand Yes Other HID® Pass-through Formats Yes Deister Prox SmartFrame® Yes (GE) Casi Rusco ProxLite Yes Kantech ioProx No

(13.56 MHZ) FORMATS SUPPORTED TABLE 2. Smart Card (13.56 MHz) Formats Supported Smart Card (13.56 MHz) Formats Supported Enabled by Default? MiFARE® Sector No MiFARE® Serial number, 32 Bit Yes MiFARE® Serial number, 56 Bit Yes MiFARE® Plus Serial number, 56 Bit Yes MiFARE® DesFire Serial number, 56 Bit No MiFARE® DesFire® EV1 Serial number, 56 Bit No iCLASS® ISO 15693 Serial number, 64 Bit Yes * PIV, TWIC, CAC, FASC-N Read Yes* (200-bit output) * PIV-I, 128 Bit, GUID Yes* (if 200-bit output is enabled) * PIV-C, 128 Bit, GUID Yes* (if 200-bit output is enabled) * Refers to cards issued under the U.S. Government Smart Card Initiative, HSPD-12.

Prox formats), all ISO 15693, and ISO 14443A credentials (badges, disk tags and key fobs). Reads both 125 kHz and 13.56 MHz credentials in the same reader. Reads U.S. Government PIV, TWIC, and CAC cards simultaneously with PIV-I (PIV Interoperable) and PIV cards. Electrical protection (reverse polarity diode protection on power lines). Data lines: high-speed transient voltage suppressor diodes. IP65-rated sealed electronics for deployment in both interior and exterior environments. Integrated reader tamper protection. PIV-I Support - The reader supports reading of a PIV-I (PIV- Interoperable) card. With a PIV-I card, the Agency code, System code and Credential number are all set to 9s. The reader senses this and outputs the full UUID (Universally Unique Identifier), which is a 128- bit long number. The firmware only supports PIV-I when the 200-bit FASC-N output is selected. PIV-C Support - The reader supports reading of a PIV-C (PIV- Credentials) card. CAC 5.5 Support - The firmware supports reading the new CAC card from Oberthur, v5.5 and outputs the FASC-N according to the firmware FASC-N setting. MIFARE 7-byte CSN Support - The reader firmware will be able to distinguish between a legacy MIFARE Classic card and a “next- generation” MIFARE classic card. The next generation MIFARE cards have a unique 7-byte serial number, not 4-byte. When presented to a reader, the next-gen card causes the reader to output a 56-bit CSN. Older cards still output a 32-bit CSN.

wall. FIGURE 1. Model SWH-4x00 Reader Backplate (includes tamper switch magnet) NOTE Mounting holes fit standard U.S. single-width electrical box and standard European (EMEA) electrical box hole patterns. Mount the reader module directly to the backplate and then snap the front cover in place as indicated in Figure 2.

(including 1 optional isolation spacer) Please note that Figure 2 shows the SWH-4100 reader and cover plate. Although the SWH-4200 keypad reader and front cover plate differ, the mounting assembly is the same as the SWH-4100.

improve the read range when mounting the reader to a metal surface. Part number: SWH-SPACER-BLK or SWH-SPACER-LGR To optimize reader range use the number of back plates as indicated in Table 3. Use of Isolation Spacers is optional and not required for non-metal mounting surfaces Installation of two SWH-4100 and SWH-4200 readers side-by-side and back-to-back Read range is not affected if the center-to-center distance between two readers is greater than or equal to four (4) inches (101.6 mm). Two readers can simultaneously read the same badge or tag if the distance between the two readers is less than 4 inches, center-to-center. If the distance between the two readers is less than four inches, field interference between the two readers may result in a double-badge read. TABLE 3. Isolation spacer recommended for mounting SWH-4100 and 4200 reader on metal Distance Reading Distance No metal plate 100% 4.5 cm 100% 2.7 cm (3 tamper plates) 85% 1.8 cm (2 tamper plates) 70% 0.9 cm (1 tamper plate) 50% 0 cm 10%

than 4 inches thick, maximum performance can be achieved by using a metal separation plate and then using isolation spacers as necessary. WIRING SWH-4100 and 4200 models have twelve terminals as noted in Table 4. The terminal strip is removable for easy installation and wiring. When attaching wires to the connector, strip off only the minimum insulation required (approx. 1/8'') and push the wire into the connector until the insulation is flush or inside the connector body. This is particularly critical for outdoor readers. While the reader itself is designed and protected to IP65 standards, the cable wires can potentially corrode and short together if not carefully mounted and tightly fastened in the connector body. TABLE 4. Connector Pins for Model SWH-4100 and 4200 Pin Description Pin 1 External Beeper Control 7 External Green LED Control 2 Ground 8 External Red LED Control 3 Power (9.4 to 16 VDC) 9 A - RS485 - used for Flash upgrade 4 D1 Wiegand 10 B - RS485 - used for Flash upgrade 5 D0 Wiegand 11 Tamper (Normally Closed) 6 Reserved for Future Use 12 Tamper (Normally Closed)

the three most common gauges of cable. TABLE 5. Maximum cable distance for 18, 20, or 22 AWG wire Wire Gauge 18 AWG 20AWG 22 AWG Cable Distance 500 feet (152 meters) 300 feet (91 meters) 200 feet (61 meters)

1. Shielded cable is recommended in electrically noisy environments. 2. You can use a local power supply for the reader. If so, don’t connect the power supply from the controller to the reader. The ground line of the local power supply must be connected to the power supply of the controller. 3. The unit needs to be operated with a power source with limited power consumption according to EN 60950-1 (2003) paragraph 2.5. Das Gerät ist mit einer Stromquelle mit begrenzter Leistung nach EN 60950-1 (2003) Absatz 2.5 zu betreiben. 4. Use of a pull-up resistor may be required by some controllers. Consult your controller manual. 5. For tamper wiring, connect Pins 11 and 12 to a normally closed supervised input, as shown in Figure 3. FIGURE 3. Normally Closed Wiring for Reader Tamper

are available from the Software House Applications Department. Program cards are used to set a specific MIFARE read key, or to change the Indala card format and other settings. To program a card reader, follow these steps: 1. Power cycle the reader. You will hear a single short beep. 2. Present the .INI card. The reader’s amber LED turns off to indicate the reader is ready for the first program card. 3. Present the first program card. The reader will respond with 5 beeps and the red and green LEDs alternately flash, and then the amber LED turns on solid. 4. If there are more program cards, repeat steps 2 and 3 until you have presented the necessary number of program cards. 5. The reader is now configured for the specified option(s) and is ready for use. For more information about programming a card reader, refer to the PDF document entitled SWH Readers Program Card Use posted on the Software House Member Center.

In some cases the reader may require a new firmware revision to enable new features or card formats that are not included in a previous revision. To upgrade the reader, you need to obtain the new firmware file from Software House, and then connect to the reader through a local RS485 connection, using terminals 9 and 10. In most cases you can use a RS485-to-USB device, or a RS232-to-RS485 converter to connect the PC to the reader. Once a physical connection is established, double-click on the firmware update utility, which is a self- running executable. A typical flash upgrade takes about 2 minutes per reader. For more information about upgrading the firmware revision, refer to the PDF document entitled SWH Readers Download Firmware to Reader posted on the Software House Member Center.

component and retry the system. Always verify wiring against the provided wiring information before powering up the reader. TABLE 6. Error Conditions and Possible Solutions Condition Possible Solutions None of the LEDs are on. Check the following:  Power connections to the reader.  Reader supply voltage at connector pin 3 and that the ground connection pin 2 is secure and well connected. The door does not open and the green LED does not light when a qualified credential is presented. Verify that the door strike and the green LED are wired correctly. Verify that the access credential has been entered and that the reader has been properly configured in the host system. The green LED does not light but the door strike unlocks the door when a valid credential is presented. Verify that the door strike is wired correctly. Refer to the appropriate wiring diagram in your controller manual. Disconnect the wire from pin 7 (green LED) and connect pin 7 to pin 2 (ground). If the green LED is now on, the reader is good and the connection to the reader is defective. If the green LED does not light, replace the reader.

Westford, MA 01886 http://www.tycosecurityproducts.com Fax: 978-577-4392 Phone: 978-577-4170 16 DRAFT Tyco CONFIDENTIAL MODEL SWH-4100 AND SWH-4200 TECHNICAL SPECIFICATIONS Cable Recommendations: 4 core (minimum), shielded, 22 AWG (minimum) cable. Connectors: 12 position, 3.5 mm Screw Terminals - Plug-In Certifications: FCC Part 15, CE and UL 294 Open Standards Compliance: ISO 14443A ISO 14443B (Depending on specific implementation) ISO 15693 (including some partially compliant credentials) Other Standards Compliance: Deister SmartFrame® in both 125 kHz and 13.56 MHz implementations HID® Prox at 125 kHz (All Formats) PIN Code Entry Keys (Model SWH-4200 only) Twelve PIN code entry keys 0-9, Command/Enter, and CE (Clear Entry) Standard Color: Black (other colors available; contact your Software House representative) Dimensions with backplate (height/width/depth): 4.37" × 3.31" × 1.10" (110.99 × 84.07 × 27.94 mm)

maximum current Environments: For both Indoor and Outdoor Use Humidity: 5 to 90% (non-condensing) Operating Temperature: -31º F to 151º F (-35º C to 67º C) Index of Protection: IP 65 (IEC 529) Read Range: 1 to 5 inches depending on credential technology and environment. Note: Read range for credentials of identical technologies may vary greatly depending on the tuning and antenna structure of each individual credential. Standard Wiegand Output including: ID Pass-Through Option Serial Number Read Fixed Wiegand bit stream option SmartFrame® encrypted MIFARE Sector read and conversion to Wiegand. Consult your Software House representative for available reconfiguration cards for your reader. 8-bit burst Wiegand PIN code (Model SWH-4200 only) PIN-on-card featured (Model SWH-4200 only) Upgrade Complete upgrade capability using RS485 port for reflashing of internal ROM.

Radio and Television Interference This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. In order to maintain compliance with FCC regulations, shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and television reception. CAUTION: Changes or modifications not expressly approved by Software House for compliance could void the user’s authority to operate this equipment.

REQUIREMENTS This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la classe A est conform à la norme NMB-003 du Canada. UL STANDARDS COMPLIANCE This reader has been tested by Underwriters Laboratories, Inc. for standard UL 294, Access Control System Units, and has been tested for compliance with Software House Controller Model # iSTAR Pro (STAR008W-64A). UL has not evaluated the RS-485 Output of this reader. Tamper Circuit Electrical Rating for UL Installations (Pins 11 & 12) is 100 mA at 30 VDC. Software House Technology Park Drive Westford, MA 01886 http://ww.tycosecurityproducts.com FAX: 978-577-4392 Phone: 978-577-4170

the instructions, is in compliance with the essential requirements and other relevant provisions of the RTTE Directive 1999/5/EC. For use in all countries of the EU. A Declaration of Conformity exists for the SWH-4100 and SWH-4200 Multi-technology readers. To obtain a copy, contact Software House and request the Declaration of Conformity document for Multi-technology readers. Software House 6 Technology Park Drive Westford, MA 01886 U.S.A. In case of alteration of the product, not agreed to by us, this declaration will lose its validity. This symbol indicates proof of conformity to applicable European Economic Community Council directives and harmonized standards published in the official journal of the European Communities.

This document contains proprietary information of Tyco International Ltd. and is furnished to its customers solely to assist in the installation, testing, operation and maintenance of the equipment described. This document may not be reproduced in whole or in part without the written approval of Tyco International Ltd. Model SWH-4100 and 4200 Contactless Multi-Technology 125 KHz and 13.56 MHz Reader Version: H0 Part Number: UM-090 May 2012 Copyright ©2012 by Tyco International Ltd. and its respective companies. All rights reserved. Product specifications and availability subject to change without notice. Certain product names mentioned herein may be trade names and/or registered trademarks of other companies.