WilTec 61029 Operation Manual

ARTICEL 61029 Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignificantly. Updating the documentation If you have suggestions for improvement or have found any irregularities please contact us. © by WilTec Wildanger Technik GmbH Seite 12 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de ...

document can be copied or duplicated in another form without the prior written consent of WilTec Wildanger Technik GmbH. The WilTec Wildanger Technik GmbH assumes no liability for any errors in this user manual or the connection diagram. Although WilTec Wildanger Technik GmbH has made every effort to make sure that this user manual is complete, accurate and updated, errors cannot always be avoided. In the event of problems with this user manual please complete and send this form back to us. FAX-notification (+++49 2403 55592-15), from: _______________ ...

Arbor Diameter 10mm Wheel Dimensions 100mm Dia. X 3.2mm Thick Overall Dimensions 175mmW x 320mmL x 210mmH Weight 1.60kgs Save this manual You will need the manual for safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep the manual in a safe and dry place for future reference. Safety Warnings and Precautions WARNING: When using tools, basic safety precautions should always be fol- lowed to reduce the risk of personal injury and damage to equipment. Read all instructions before using this tool! ...

fully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts, any broken parts or mounting fixtures, and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. Do not use the tool if any switch does not turn On and Off properly. 13. Guard against electric shock. Prevent body contact with grounded surfaces such as pipes, radi- ators, ranges and refrigerator enclosures. 14. Replacement parts ...

as shown in the mounting picture in FIGURE 1. 2. Bolt (bolts are not included) the unit directly to the workbench through the two 1/4" holes on the base (#40). The workbench must have a solid surface capable of supporting the weight of this sharp- ener, the work-piece and assorted tools. See FIGURE 2. Figure 1: Figure 2: 1/4” Hole with Bolt Base (#40) Warning! Always unplug the unit before changing grinding wheels or when making any adjustments to the Sharpener. Mounting a Grinding Wheel Refer to the assembly drawing and FIGURE 3 and FIGURE 4 b ...

Refer to the assembly drawing on and the various photographs. Note: Raise the top housing while adjusting the chain. 1. Clean the chain before sharpening it. Wash it with a non-flammable solvent. Don’t use gasoline to dry the chain. 2. Lift up the Chain Stop (#53) and secure the chain in the Fixed Disk (#50). See FIGURE 6. 3. Lower the Chain Stop (#53) so that it is positioned on the tooth (blade) you want to start with. See FIGURE 5. Tip of Chain Stop positioned against tooth. 4. See FIGURES 5&6. Loosen the Lock Wheel (#46) to allow entire housing to turn. Rotate the ho ...

(#50) by turning the Screw (#52). See FIGURE 8.The Screw (#52) should be situated so that you can easily release and tighten it . You will need to release it each time you move to the next link, and tighten it to sharpen each link. 9. If the chain has been repeatedly sharpened, the chain depth limiting gauges may need to be taken down with a flat file(not included). See FIGURES 8&9. File down each gauge so that they are at a lower level than cutting teeth. 1. Put on your protective gear and make sure the immediate area is clear of bystanders. 2. Plug in the Power Cord (#23) and press the green button on the ...

2. Check the grinding wheel before each use to make sure it isn’t damaged. Do not use a grinding wheel if it is chipped, cracked, or worn. You can check if the wheel has cracks not visible to the human eye by hanging it up by the central hole and tapping it with a non metal object (ie: screwdriver handle). If it is in good condition it will produce a metallic sound. A dull sound indicates a crack or break. 3. Replace the grinding wheel when it grinds down to a diameter of 3 inches. Parts List Part# Description QTY Part# Description QTY 1 Safe Guard 30 Bolt 2 Grinding Whe ...

Seite 20 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de ...

implemented in the law related to electrical and electronic equipment and appliances. All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste. The company WilTec Technik GmbH has been registrated in the German registry EAR under the WEEE-registration number DE45283704. Disposal of used electrical and electronic appliances (intended for use in the countries of the European U ...