Whispbar K718W Fitting Instructions Manual
Text of Whispbar K718W Fitting Instructions Manual
Whispbar K718W Fitting Instructions for Basic Carrier
D
Montageanleitung für Basisträgersystem
ES
Instrucciones de montaje para el sistema
de transporte
F
Instructions de montage pour Basic Carrier
NO
Monteringsanvisning for takstativ
PT
Instruções de Montagem para sistema de
transporte.
RU
Установочные Инструкции для
Поперечных Балок
x 1
x 1
x 1
x 1
x 2
x 1
x 1
x 2
Revision No: 1A
1
MAX kgs (lbs)
W/P
WHD
Renault
Clio , 5dr Hatch Sep 13-+
AU
50 kgs (110 lbs)
Clio , 5dr Hatch Sep 13-+
EU
50 kgs (110 lbs)
Clio , 5dr Hatch Sep 13-+
ZA
50 kgs (110 lbs)
Clio , 5dr Hatch Sep 13-+
CN
50 kgs (110 lbs)
3
Whispbar K718W First Time Installation
G Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
G This kit fits type A, B, C and D.
G These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4
G Use keys to remove covers.
G Use hex screwdriver to reverse adjusting
screw 10 turns.
G Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
G Ensure each end of the crossbar is
adjusted equally.
5
G Remove locking screw.
G Apply protective strip as shown.
Trim if required.
G It is important to put the clamps in the
correct position on the vehicle.
G Letters refer to the part numbers stamped
on clamps.
G Clamp Part Number:
A = 059A
B = 060A
C = 061A
D = 062A
6
G Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
G Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
G Refer to the underside of the pad for the
part number.
7
G It is important to put the pads in the correct
position on the vehicle.
G Letters refer to the pad part numbers and
position.
G Pad Part Number:
A = 239A
B = 261A
C = 262A
G Place rubber pads (supplied with fitting kit)
on the vehicle roof. Pad may vary in shape
to that shown.
G Make sure the pad fits into the holes
underneath the foot.
8
G Clamps directly to edge of roof under the
doors
G Please check the rear of this manual for
information relating specifically to your
vehicle.
G Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
G Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
G Ti
Whispbar K718W G Tighten locking screw on both legs evenly.
G Check crossbar is securely attached to the
vehicle.
G Use keys to fit and lock covers
10
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
11
G Clean the car roof and surfaces of the
product that will be in contact with the car
roof.
G Follow the fitting instructions for fitting the
product to your vehicle. Make sure all steps
are carried out in order.
G Set crossbars a minimum distance of
700mm (27 1/2") apart where no other
distance is specified in the fitting
instructions. This is especially important
when carrying long loads.
G Check unit is securely attached
G Check and replace worn out or defective
parts.
G Keep the product clean and maintained.
G Never drive into a car wash with the roof
rack system fitted.
G Lubricate locks and adjusting screws at
regular intervals.
G Remove the products from the vehicle
when not in use. Make sure all loose parts
are stored safely.
G Yakima Products, Inc.
Archimedesbaan 25
3439 ME Nieuwegein
The Netherlands
+31 (0)30 600 1070
www.whispbar.eu
www.whispba
G Komponenten aus der Verpackung
nehmen und überprüfen. Setzen Sie sich
mit Ihrem Händler in Verbindung, sollten
Teile fehlen oder beschädigt sein!
G Dieses Kit ist für die Typen A, B, C und D.
G Dargestellt ist der Querträger des Typs A.
Die Anweisungen gelten aber auch für die
Typen B, C und D!
BITTE BEACHTEN: die in dieser Anleitung
gezeigten Klammerillustrationen können von den
Klammern dieses Zubehörsatzes
G Abdeckungen mit Schlüsseln abnehmen.
G Innensechskantschlüssel benutzen und
Stellschraube mit 10 Umdrehungen lösen.
G Befestigungsschraube eindrücken und
Querträgerschenkel ausziehen. Siehe
Anweisungen für das Einstellen der
Querträger!
G Sicherstellen, dass beide Enden der
Querträger gleich lang eingestellt sind
(Maß 'x', s. Abb.).
15
G Stellschraube entfernen.
G Sicherheitsstreifen wie gezeigt anbringen.
Wenn nötig, zurecht schneiden.
G Es ist wichtig, die Klammern an der
richtigen Position am Fahrzeug
anzubringen.
G Die Buchstaben beziehen sich auf die in
die Klammern eingestanzten
Teilenummern.
G Klammer-Teilenummern:
A = 059A
B = 060A
C = 061A
D = 062A
16