Seashell SS-1 Operation & User’s Manual
Text of Seashell SS-1 Operation & User’s Manual
Page 3
Page 4
Contents
Components
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Components..........................................................................................4
Introduction ...........................................................................................5
Disclaimer .............................................................................................5
Unpacking...............................
Thank you for choosing the Seashell Customized
Waterproof Camera Housing.
The Seashell is the world’s first customized
waterproof camera housing suitable for many
different compact digital camera models. The
versatile Seashell can be used at the beach,
pool, for scuba, snorkelling, swimming and
many outdoor activities. It can operate down
to a 131 foot depth. A few minutes are all that
required for custo
Configuring a Seashell
Page 7
Page 8
Attention!
It is very important to read through following
safety precautions before using your Seashell
water proof camera case in order to guarantee
safety and to avoid any damage.
If water leaks, remove the camera housing
and camera from water as quickly as possible.
Remove the camera from Seashell camera
housing when not in use for an extended
period.
Avoid direct sunlight, heat or fire.
Do not use Seashel
Installing the Dove Tail Shims & Actuator
Shafts
Installing the Actuator Shafts
Choosing the correctly matched Dove Tail
Shims and Actuator Shafts
•
•
•
•
•
•
•
•
•
Lay camera on the Fitting Sheet (Cross
Section Diagram) on a flat surface facing
up with the camera switched off.
Position the lens of the camera as close to
the cross-hairs on the Fitting Sheet as pos-
sible, but ensure that the camera is inside
the black outer
Loading the Front Spacers
Note: In case an Actuator Shaft is not
used, install a short Actuator Shaft to lock
the Hanging Clamp in place. In this case
the camera will need to be switched on
before closing the housing. The camera
need to operate continuously on with the
Auto-Off feature deactivated.
Note: Do not over-tighten. Over-tightening
may damage the Hanging Clamp.
•
•
•
•
•
•
•
Use the Mini Wrench to lock the actuato
Attaching the Back Foam Pad onto the
Rear Housing
Page 13
Page 14
Water Leakage
Testing the of the Camera
•
•
•
•
•
•
•
•
•
•
•
•
•
Follow the measuring procedure from page
12. Then, select the appropriate Back
Foam Pad and start the installation.
Put Seashell camera case on a flat surface
with the rear housing facing up, open the
rear housing.
Put the camera into the front housing.
According to the screen size of the camera,
take
Maintenance of the Main O-Ring
Maintenance of the Small O-Rings at the
Shutter and Power button
Maintenance of the Seashell Housing
Preparation of Camera
Camera Settings
Keep the main o-ring clean, as a dirty o-ring
may cause leakage. When the o-ring becomes
dirty:
By hand, remove the o-ring from the slot of
Seashell camera housing. Avoid using
sharp tools which may damage the o-ring.
Do not overstretch the o-ring as it may
cause damage.
Preparation of the Seashell
Loading the Camera into the Seashell
Storage
Photographing
Specifications
•
•
•
•
•
•
•
•
•
Fasten both ends of the Neck Strap or the
Hand Strip to the Strap Mounts of Seashell.
Use of the Neck strap underwater is dangerous
as the Neck Strap may be entangled and
cause strangulation or other mishap.
Apply an anti-condensation solution to the
inside face of the lens window if required.
Do not use