Perlesmith PSLFK1 Manual
Text of the manual
1/2 in. (12.7 mm)
7/32 in. (5.5 mm)
Wood Drill
Screw Driver
Hammer
WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER
INSTALLATION OR ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING.
If you do not understand the instructions or have any concerns or questions, please contact a
TV Bracket (Left and Right)
Arm Extensions 03 x2
04 x2
Front Support 02 x1
5/16 x 2½ in
Lag Bolts
x4
A
Washers
Ø8mm
x4
B
x1
C
Philips Screws
M8 x 15mm
M8 x 45mm
Philips Screws
M6 x 15mm
M6 x 30mm
Washers
Ø6mm
M4-5-6
Spacers
L10mm
x4
x4
x4
x4
x8
x4
M-A
M-B
M-C
M-D
M-E
M-F
Spacers
L5mm
x8
M-G
Arm and
Wall Plate 01 x1
Supplied Hardware
Socket
Span
Step 1 Before TV Bracket Installation
75 mm ≈ 2 7/8 in
100 mm ≈ 4 in
200 mm ≈ 7 7/8 in
300 mm ≈ 11 3/4 in
400 mm ≈ 15 3/4 in
600 mm ≈ 23 5/8 in
400mm (15 3/4 in)
Max 600mm(23 5/8 in)
Max
Measure the distance between the holes located
at the back of your TV (these measures may form
the shape of a square, or a rectangle) and check
that these ta
For Flat Screen TV
For Curved TV
Step 2 Install TV Bracket
or
or
Use a stud finder (not included) to locate wood
studs. Mark the edge and center locations.
16in(406mm)
Step 3A
3-1
3-2
Use wall plate 01 to mark mounting location x4 locations.
Ensure marking at the
center of the stud.
01
01
all-guides
com
Drill 4 pilot holes using a 7/32 in. (5.5 mm) diameter drill
bit. Make sure the depth is not less than 2 3/4” (70mm).
7/32 in.
Ø5.5 mm
in. (70 mm)
Mount the wall plate using 4 sets of 5/16 lag bolts (a) and
washers B with a 1/2 in. socket wrench (not included).
A
B
3-4
3-3
1/2 in. (12.7 mm)
socket wrench
01
2
B
A
UP
01
Use socket spanner C to remove the
pre-assembed nuts and screws S4
from the extensions 02 and save
them to use.
Insert the extensions into the .
03
02
4-2
4-1
4-3
Fasten the nuts and
screws S4 x8.
4-4
S1
S2
Hang 02 and 03 into 01 , and using Screw Driver secure with
pre-assembled screws and washers .
02
S4
Step 4 Inst
Secure TV with brackets
against the arm
extensions and
with the pre-assembled
screws [S3] .
04
S3
03
02
Hang TV with brackets 04
onto the arm extensions 02
and 03 .
Step 5 Hang TV
Step 6 Secure TV
04
03
04
02
04
[S3]
Screw
Lock
driver
Remove the preassembled
screws [S3] and save to use,
then raise the safety locks.
[S3]