KE2 EvapOEM Quick Start Manual

Text of the manual

© Copyright 2019 KE2 Therm Solutions, Inc., Washington, Missouri 63090

Q.1.45 May 2019 KE2 EvapOEM pn21231 Quick Start Guide This reference should remain on site with the installed KE2 Evap OEM controller. Get your controller online, & beneft from remote monitoring, control, and text / e-mail alarm notices. Just a few easy steps, with KE2 Smart Access Pr

LL SOLENOID/COMP RELAY

BK/OR L1 WT/R L2 HS GND P/N 20996 12 AMP 20 AMP 3 AMP OR NEUTRAL HEATERS thermsolutions® R/W BL/BK BK BL/BK FROM CONTROLLER EC MOTOR RELAY NO NC COM TSuc Aux3 Aux2 Aux1 TCoil TAir 0 - 10V OUTPUT ETHERNET DISPLAY DEFROST RELAY SOLENOID (COMPRESSOR) RELAY FAN RELAY Blue Orange Yellow Red Black Empty Red Gr

Q.1.45 May 2019

Page 3 KE2 EvapOEM Quick Start Guide © Copyright 2019 KE2 Therm Solutions, Inc., Washington, Missouri 63090 Wiring Diagram - Controller without KE2 Terminal Board NO COM NO COM NC FAN RELAY COMPRESSOR RELAY DEFROST RELAY COM NO L1 N/L2 VOUT MOTOR Aux3 Aux2 Aux1 TCoil TAir TSuc PSI RS-485 HS DEFROST HEATERS FANS S LLS NC N X BLK RED BLK FIEL

Q.1.45 May 2019

Page 4 KE2 EvapOEM Quick Start Guide © Copyright 2019 KE2 Therm Solutions, Inc., Washington, Missouri 63090 IMPORTANT Steps to Ensure Proper Coil Sensor Location Installing the Sensor - The most active portion of the sensor is the first 1/2” of the probe. The inset photo in Figure 2 shows that the sensor is positioned so that it is touch

Q.1.45 May 2019

Page 5 KE2 EvapOEM Quick Start Guide © Copyright 2019 KE2 Therm Solutions, Inc., Washington, Missouri 63090 Changing Setpoints Pressing and holding the ENTER button will enter the Basic Setpoints menu. Press ENTER button to toggle between setpoint and value. Pressing and holding the BACK button will enter the Advanced Setpoints menu. Press E

Quick Start Guide

Q.1.45 May 2019 Page 6 Menus and Parameters ADVANCED Setpoints Menu Basic (Remote) Display KE2 Combo Display Min Max Default Description Abbreviation Scrolling Text tS tS ROOM TEMP -50.0 0F 90.0 0F 0.0 0F Room Temp Setpoint - Walk-in room temp to be maintained rFG rF REFRIgERANT N/A N/A R-404A Type of refrigerant used: See tabl

© Copyright 2019 KE2 Therm Solutions, Inc., Washington, Missouri 63090

Q.1.45 May 2019 Page 7 KE2 EvapOEM Quick Start Guide ADVANCED Setpoints Menu (continued) Basic (Remote) Display KE2 Combo Display Min Max Default Description Abbreviation Scrolling Text EdF EdF EXTREME TEMP DIFF 0 0F 99.9 0F 20.0 0F ADVANCED TOPIC: Call KE2 Therm for assistance CLA CLA C

Quick Start Guide

Q.1.45 May 2019 Page 8 © Copyright 2019 KE2 Therm Solutions, Inc., Washington, Missouri 63090 First Time Setup - Types of Control & KE2 Smart Access Basic (Remote) Display KE2 Combo Display Description Abbreviation Scrolling Text Ed Ed ELECTRIC DEFROST /TEV Electric Defrost w/Mechanical valve EdE EdE ELECTRIC DEFROST /EEV Elec

Q.1.45 May 2019

Page 9 © Copyright 2019 KE2 Therm Solutions, Inc., Washington, Missouri 63090 KE2 EvapOEM Quick Start Guide Alarm Status Menu Basic (Remote) Display KE2 Combo Display Description Abbreviation Scrolling Text PSA PSA PRESSURE SENSOR Suction pressure sensor is shorted, open or pressure out of range SSA SSA SUCTION TEMP SENSOR Suction temperatur

© Copyright 2019 KE2 Therm Solutions, Inc., Washington, Missouri 63090

Q.1.45 May 2019 Page 10 KE2 EvapOEM Quick Start Guide dCL dCL Door Switch - Door Closed Auxiliary Input Door switch indicates door is closed ddF ddF Defrost Delay Fan System Mode At defrost, fans will continue running for several minutes, using stored cooling in the coil. Once the coil r

Other Controller Manuals