INAZUMA WebCSA Series Operating Instructions Manual

Text of the manual

w w w . i n a z u m a - o n l i n e . c o m

Control WebCSA Power Switch WebCSA Add-On Temperature Sensor WebCSA Water Level Regulation WebCSA Operating Instructions Control WebCSA, App & Accessories The initial setup of the control requires an iOS device with an active SIM card iOS version

General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.2. Important safety notes and warnings . . . . . . . . . . . . . . . . 2 1.3. Warning label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.4. Manufac

w w w . i n a z u m a - o n l i n e . c o m

! 1.6. EC-Declaration of Conformity Manufacturer: Inazuma Johannes Kurzweil GmbH Eisackstraße 16 DE – 86165 Augsburg Tel.: +49 (0)821-72 919 72 Fax.: +49 (0)821-72 919 73 Directives in use: Machinery Directive: 2006/42/EG, “Low Voltage” Directive: 2006/95/EG, General Product Safety Directive: 2001/95/EG S

2.2. Before commissioning

Before commissioning the filter, the system must be filled with water and the cover must be closed. • Control is splash proof (IP65) • Protect from direct solar radiation! • To wall mount the drum filter control, please use the provided wall mounting panel. • Do not drill any holes into the case, otherwise the warranty wil

w w w . i n a z u m a - o n l i n e . c o m

2.5. Initial operation and functioning of the control The commissioning of the control is done by establishing the power connection. To do this, plug the power plug of the controller into a 230 V Schuko socket. The starting process of the controller takes about 1 to 2 minutes. The controller acknowledges the suc

3. Configuration: Make sure the floats are in the position

shown above before power is applied. After power is turned on, the software boots up (may take 2 to 3 minutes). When the software has successfully started, you will hear: if there is no configuration assigned: 2 beep sounds if there is a configuration assigned: 4 beep sounds followed by a single lo

w w w . i n a z u m a - o n l i n e . c o m

3. WebCSA app & Inazuma WebCSA cloud 3.1. Registration and installation 1. Download the current version of the iOS in the Apple Store and run it 2. Connect the float switches 1 + 2 to the control, set float switch in reset mode (see left picture) 3. Connect the control to the mains 4. Open the Inazuma WebCSA app

6. Start initial setup

Click on the button “Set up new control unit”. Further steps are displayed in the app. 7. Switch on the personal hotspot To connect your device to the control unit, you have to turn on your personal hotspot. You can activate it in the menu Settings -> Enable personal hotspot Set the password to Inazuma2018 Then click in the app o

w w w . i n a z u m a - o n l i n e . c o m

14. IP address of the control unit If a successful connection has been established between the controller and your home network, the screen will display the IP address assigned to the control unit. Please write it down and then click on Finish. 15. Log in to the app In the start screen of the Inazuma app, click o

Opens up the help page for the current page.

Power Switch [P1] ([P2] [P4] [P4] Art.Nr. IK5002) Displays the status of each Power Switch output. A green background means that an output is active. By short tapping, the outputs can be switched on and off. A long pressing of the buttons opens up the “Power Switch” settings menu. WLAN symbol Displays

Other Control Unit Manuals