Whispbar K716W Instructions Manual
Text of Whispbar K716W Instructions Manual
Fitting Instructions for Basic Carrier
D
Montageanleitung für Basisträgersystem
ES
Instrucciones de montaje para el sistema
de transporte
F
Instructions de montage pour Basic Carrier
NO
Monteringsanvisning for takstativ
PT
Instruções de Montagem para sistema de
transporte.
RU
Установочные Инструкции для
Поперечных Балок
x 1
x 1
x 1
x 1
x 2
x 1
x 1
x 2
x 2
x 2
x 1
x 1
Revision No: 1A
1
MAX kgs (lbs)
W/P
WHD
Toyota
Rav 4 , 5dr SUV Jan 13-+
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
Rav 4 , 5dr SUV Jan 13-+
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
Rav 4 , 5dr SUV Jan 13-+
EU
75 kgs (165 lbs)
75 kgs (165 lbs)
Rav 4 , 5dr SUV Jan 13-+
US
75 kgs (165 lbs)
75 kgs (165 lbs)
2
First Time Installation
G Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
G This kit fits type A, B, C and D.
G These instructions show type A crossbar
fitted. They also apply to type B, C and D.
G Use keys to remove covers.
3
G Use hex screwdriver to reverse adjusting
screw 10 turns.
G Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
G Ensure each end of the crossbar is
adjusted equally.
G Set bars to length (revert to rear of these
instructions).
G Please check the rear of this manual for
information relating specifically to your
vehicle.
4
G Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
G Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
G Select plastic internal block (from fitting kit)
and insert into foot.
5
Whispbar K716W G Open or remove fixed-point covers.
G Store items away in a safe place.
G Letters refer to the part numbers stamped
on clamps.
G Clamp Part Number:
A = 239A
B = 241A
G Hook clamps into the fixed points on the
vehicle.
6
G Place ditch mould insert over the clamp.
G Repeat at other end.
G Refer to the underside of the pad for the
part number.
G Letters refer to the pad part numbers and
position.
G Pad Part Number:
A = 296
B = 297
7
G Place pads on roof as per diagram. Screw
thread should be vertically through square
hole in pad.
G Place crossbar foot over clamp bolt.
G Tighten the plastic knob. The side with the
nut showing should be facing up.
8
G Ensure the plastic knob is in the position
shown when fully tightened.
G Repeat at other end.
G Check crossbar is securely attached to the
vehicle.
G Use keys to fit and lock covers
G Use keys to remove covers.
9
G Use hex screwdriver to reverse adjusting screw 10 turns.
G Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
G Ensure each end of the crossbar is
adjusted equally.
G Remove locking screw.
10
G Apply protective strip as shown.
Trim if required.
G A, B = Clear
C, D = Grey
G It is important to put the clamps in the
correct position on the vehicle.
G Letters refer to the part numbers stamped
on clamps.
G Clamp Part Number:
A = 055A
B = 056A
G Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
11
G Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
G Refer to the underside of the pad for the
part number.
G It is important to put the pads in the correct
position on the vehicle.
G Letters refer to the pad part numbers and
position.
G Pad Part Number:
A = 244
12
G Place rubber pads (supplied with fitting kit)
on the vehicle roof. Pad may vary in shape
to that shown.
G Make sure the pad fits into the holes
underneath the foot.
G Clamps directly to edge of roof under the
doors
G Please check the rear of this manual for
information relating specifically to your
vehicle.
G Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
13
G Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
G Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
G Tighten locking screw on both legs evenly,
3 Nm (2.2 ft lb).
14
Whispbar K716W G Check crossbar is securely attached to the
vehicle.
G Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
15
Whispbar K716W G Clean the car roof and surfaces of the
product that will be in contact with the car
roof.
G Follow the fitting instructions for fitting the
product to your vehicle. Make sure all steps
are carried out in order.
G Set crossbars a minimum distance of
700mm (27 1/2") apart where no other
distance is specified in the fitting
instructions. This is especially important
when carrying long loads.
G Check unit is securely attached
G Check and replace worn out or defective
parts.
G Keep the product clean and maintained.
G Never drive into a car wash with the roof
rack system fitted.
G Lubricate locks and adjusting screws at
regular intervals.
G Remove the products from the vehicle
when not in use. Make sure all loose parts
are stored safely.
G Yakima Products, Inc.
Archimedesbaan 25
3439 ME Nieuwegein
The Netherlands
+31 (0)30 600 1070
www.whispbar.eu
www.whispba
Whispbar K716W G Komponenten aus der Verpackung
nehmen und überprüfen. Setzen Sie sich
mit Ihrem Händler in Verbindung, sollten
Teile fehlen oder beschädigt sein!
G Dieses Kit ist für die Typen A, B, C und D.
G Dargestellt ist der Querträger des Typs A.
Die Anweisungen gelten aber auch für die
Typen B, C und D!
G Abdeckungen mit Schlüsseln abnehmen.
18
G Innensechskantschlüssel benutzen und
Stellschraube mit 10 Umdrehungen lösen.
G Befestigungsschraube eindrücken und
Querträgerschenkel ausziehen. Siehe
Anweisungen für das Einstellen der
Querträger!
G Sicherstellen, dass beide Enden der
Querträger gleich lang eingestellt sind
(Maß 'x', s. Abb.).
G Beide Stangen auf Länge einstellen. (siehe
Rückseite dieser Anleitung)
G Im hinteren Teil dieser
Bedienungsanleitung finden Sie
I