Turnstone Campfire Assembly Instructions Manual
Text of Turnstone Campfire Assembly Instructions Manual
X screw (16)
size: #10 x 1.075"
trim plate (2)
T-slot fastener (16)
electrical (2)
leg (2)
middle support (1)
rail (1)
half worksurface (2)
trough (1)
really
easy
assemble time:
40 minutes
difficulty scale
time needed
tools needed
time needed
a little
more diffcult
assembly video
Here's what's in the box
For assembly videos go to myturnstone.com/campfire/instructions
myturnstone.com/campfire/instructions
• Ask a friend for help to lift the
first half worksurface onto the leg
structure. You’ll notice the edge that
faces outward is slightly rounded
and the inside edge is straight.
• Carefully line up the holes on the
bottom of the worksurface with the
metal extrusions on the top
of the base.
• After the worksurface top is in
place, tighten the cam-locks
underneath the table.
4x
1
STEP
• Find the two leg pieces and place upright.
• Thi
• Install the T-slot fasteners loosely into
the center trough by inserting the
screws into the pre-drilled holes and
turning loosely from the bottom.
16x
T-slot fastener
Install T-slot
fasteners.
tip
Use the packaging
to balance the
trough on its side
to easily connect
the fasteners.
4
STEP
• Place trough underneath the worksurface
and make sure the two rows of fasteners
straddle the center rail.
• After the trough is in place, look for the
• Install the trough-end trim
plates. Be sure the longer
side of the trim plate goes
on the inside and the lip
covers the edge of the leg.
• After the trim plates are
in place, tighten from
underneath the installed
worksurface using the
X screws.
View from under big table.
Install
trough-end
trim plates.
Install
other half
worksurface.
1
2
3
4
5
6
7
8
9
10
11
• Call over your friend again to help place the
second half worksurface ont
View from under big table.
• Fasten the trough to the half
worksurface from underneath
using the X screws.
Tighten
trough to
worksurface.
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
Tighten trim
plate.
View from under big table.
• Tighten the trim plates
fromunderneath using
the X screws.
Use X screw.
size: #10 x 1.071"
Use X screw.
size: #10 x 1.071"
• Install both electrical
components into the
trim plates.
• Feed the plug down to the
outlet. The remaining cord
feeds into the trough.
• Snap latches into place
to secure, depress
latches to release.
• The electrical lines will
rest inside the trough.
Install
electrical.
Connect
electrical
lines.
tip
The outlets pop
open by pressing
on the top. Once
they are installed,
the electrical
outlet will face
the center of the
table.
ti
• Line up T-slot fasteners and set
the center rail on top.
• The rail will snap into place.
• Duck under the big table and
tighten the center rail into place
by rotating the T-slot fasteners.
1
2
3
4
5
6
7
8
9
10
11
Visit myturnstone.com to see more spots.
All rights reserved. ©2010 Steelcase Inc. Printed in the U.S.A. on recycled paper. E Data subject to change. Trademarks used herein are the property of Steelcase Inc.
Some products and services may not be available in all countries. Your Turnstone representative can provide you with details.
ad-stock ID 10-0003018. Campfire Big Table with Trough Assembly Instructions: 11/10
engineering document 939500545 rev A.