Sesamo Puma Millenium Installation Instruction

page 5 Automatism installation preparation.................................................................... page 5 Automatism description ...................................................................................... page 5 Sizes and dimensions .......................................... ...

performance, Sesamo recommends you carefully read and follow the installation and use instructions found in this man- ual. Installation of this automatism must only be performed by the professionally qualified personnel for whom this man- ual is addressed. Any errors during installation may be harmful to people or things. Packaging material (wood, plas- tic, cardboard, etc. ...

The automatism is prepared to work in different accessory and periph- eral configurations. According to the selected configuration, arrange the cables necessary for wiring all the peripherals. Fig.1 shows an example of complete installation including: A. Entry Radar B. Active safety sensor C. Safety closing device D. Logic selection selector E. Opening button at exit WARNING If two single Piuma a ...

The Piuma Millennium automatism is available in two configurations: with standard heads in aluminium (L=810 mm) and with flat heads (optional) in steel (L=800 mm). Standard End Sides Flat End Sides (opzionali) Fig. 5 Fixing Holes (Std End Sides) Fixing Holes (Flat end sides) Gearmotor axis Gearmotor axis A A A A A A A A Fig. 3 Fig. 4 all-guides com ...

motor body. Positioning dimensions (rigid pull arm) The rigid pull arm is used when the automatism is installed on the swing side of the door . WARNING : For a correct positioning, always use the main axis of the door hinges and the operation axis of the gearmotor as a reference, as show ...

Articulated push arm Standard End Sides 300 12÷24 50 380 Hinge axis Articulated push arm Door Attachment Gearmotor Axis Fig. 8 The heights of the prepa- red fastening holes are shown in Fig. 4 and 5. For right-hand opening doors (anticlockwise direc- tion), the assembly of th ...

Disassemble the push arm (if present) (Fig. 10 Part A) by unscredoor the counter-sunk head screw M6 x 70 (Fig. 10 Part B). Extract the top hexagonal stop (Fig. 10 Part C). Remove the aluminium cover (Fig. 10 Part D) by pulling it outwards. To facilitate the fastening of the automatism, it is possible to remove the heads (Fig. 11 Part A) and move or remove the internal compo ...

Insert the threaded hexagon in the upper part of the hexagonal hole of the gearmotor (Fig.12 part.A). Assemble the rigid pull arm (Fig.12 part.B) to the upper hexagon with the flathead screw M6x70 supplied (Fig.12 part.C) after having interposed the washers Ø6,4x12 (Fig.12 part.D) as shown in the figure 12. Before tightening the flathead screw, check carefully that t ...

Reach the guide fixing box (Fig.16 part.A) taking off the S924/A cap (Fig.16 Part.B). Make at least 4 holes corresponding to the “V” shape in the guide profile. Use these holes to fix the guide to the frame with appropriate screws. Insert the cylindrical runner (Fig.16 part.D), with the relative shaft, inside the guide and distribute a uniform layer of grease on ...

RIGID PULL ARM Insert the lock (Fig.17 part A) inside the spline according to the indications provided on page 11. Open the door to the desired amplitu- de, then bring the lock in contact with the cylindrical runner (Fig.17 part B) and tighten the screw on the lock. ARTICULATED PUSH ARM Assemble the optional stop (Fig.18 Part.B) on the articulated arm (Fig.18 Part.A) using the screws su ...

tions make sure the mains are disconnected. Before powering the equipment, perform the controls foreseen in paragraph “Start up”. Place the power cord in the automatism paying careful attention not to damage the cord against any metallic edges. Connect mains and grounding wires on the terminal board (Fig. 19) WARNING : Never invert the power wire with the grounding wire. Power must be ...

in the terminal board (part. A) observing the assembly direction as shown in Fig. 21 Electric Transformer Battery Encoder Gear Motor Fig. 22 Part. A Verify the agreement between the power motor cable and the serigraphy indicated in the electronic board + _ Left Side Electronic Board Connections Fig. 22 summarises terminal connections on the left side of the electro ...

A. Photocell amplifier board connector (optional) Insert the amplifier module observing the assembly direction shown in Fig. 21 WARNING Select the Jumper for single or double beam and check the red led B. Photocell beam connector (only use if the internal photocell amplifier board module is installed) C. Selector Jumper between Millennium - and external cell amplifier The ...

Use the four conductors in the shielded wire for connections, observing the correspondences indicated by the markings on the terminal board and multi-logic selector. Do not connect the shield of the wire used. For further information on multi-logic selector use, see the instructions for use. E. External peripheral power connector – 12 Vdc 6W max (500mA) Real power value may va ...

The electrical signal from external peripherals can be varied through the advanced selector or PC connection: from nor- mally closed to normally open and vice versa. See the advanced selector used manual for further details. G.Connector for PC - unit connections A PC connection board (optional) is required to connect the MILLENNIUM unit to a Personal Computer. The foll ...

voltage present ON indicates encoder signal presence ON indicates electronic lock power ON indicates 12V external peripheral power supply Fig. 29 Factory use only LED Functions Diagnostics Led (see Error Message Table) External peripheral signal presence led. ON indicates motor power supply Jumper Function Jumper ON OFF (Default) J1 24V 12V J2 Door Weight > 100kg Door Weight <100kg J3 Cyclic O ...

(Door Left Opening or Door Right Opening) S8 OFF RIGID PULL ARM (Door Left Opening or Door Right Opening ) In order to optimize the operation of the automatism, it is necessary to set the jumper according to the following diagram: Selection of the door weight For correct automatism operation and in order to guarantee optimization of the parameters that regulate door movement, carry ou ...

logics: - DEFAULT: the selector acts on all the automatisms connected to it without any distinction. For example, if the selector is used to set the Stop Open logic, all the automatisms connected to it will work with the Stop Open logic. - MULTISLAVE: with this logic up to 3 automatisms can be connected, each identified ...