Baxi MULTIFIT Flue Systems Guidance Notes

Text of Baxi MULTIFIT Flue Systems Guidance Notes

© Baxi Heating UK Ltd 2011

G U I D A N C E N OT E S Flue Accessories & Fitting Guide Ø 60/100 Flue Systems Ø 80/125 Flue Systems Ø 80/80 Twin Flue Systems Plume Displacement Kit (Ø 60/100 Flue Systems) READ THESE INSTRUCTIONS IN CONJUNCTION WITH THE BOILER INSTALLATION INSTRUCTIONS BEFORE FITTING THE FLUE Please leave these instructions with the Installation & Servicing Instructions. IMPORTANT NOTE: This document will assist in the correct installati
© Baxi Heating UK Ltd 2011 • Flue systems must be constructed using only components approved for use with the appliance and installed in accordance with BS 5440 Part 1, any manufacturers instructions and Part J of the Building Regulations. • In order to meet the requirements of the Gas Safety (Installation & Use) Regulations, provision should be made such that all flue joints and supports can be inspected. • The flue system should have a cont
© Baxi Heating UK Ltd 2011 A B K, K1 R D C N U S L H J M FLUE ACCESSORIES Flue Groups Ø60/100 Flue Systems - with Positive Fix Ø80/125 Flue Systems Ø80/80 Twin Flue Systems E G F A4 G N A Y, Z Key Accessory Size Code No FLUE GROUP A Concentric Flue System 60/100mm diameter A Telescopic Flue (Black) 315-500mm 720598701 A Telescopic Flue (Brown) 315-500mm 720642701 A Telescopic Flue (White) 315-500mm 720599401 A Telescopic Flue Neta-tec & Platinum
© Baxi Heating UK Ltd 2011 CONCENTRIC FLUE SYSTEM (60/100) ONLY - FLUE GROUP A USE OF SUPPORTS & SECURING Each extension and securing screws (1m, 500mm & 250mm) is supplied with a support bracket. Additional support brackets can be purchased separately (see Flue Accessory page overleaf). DO NOT use brackets other than those supplied or shown in this guide. The flue system MUST be supported AT LEAST once every metre of actual length, and every strai
© Baxi Heating UK Ltd 2011 Y X NOTE: Horizontal flue pipes should always be installed with a 1.5° to 3° fall from the terminal to allow condensate to run back to the boiler. Push the flue deflector over the terminal end and rotate to the optimum angle for deflecting plume. Secure the deflector to the terminal with screw provided. Do not direct the deflector upwards or downwards. NOTE: A terminal guard is still required when circumstances dictate
© Baxi Heating UK Ltd 2011 Y X Y X Y X C 0.5m Total Equivalent Length Roof Terminal Roof Terminal A 1m B 1m C 0.4m Roof Terminal A 0.7m B 0.3m This bend is equivalent to 1 metre Total Equivalent Length = A+B+C+1x90°Bend All vertical and angled runs must be included, measured from the boiler adaptor (point X) to the joint with the flue terminal (point Y). One 93° bend or two 135° bends can be included without reduction of the flue length. If furt
© Baxi Heating UK Ltd 2011 Fixing Tie Fixing Tie Ridge Line Ridge Flue Terminal - Suitable for Flue Group A (60/100) The MAXIMUM equivalent flue length when using this terminal is 8 metres ! Special Notes This flue terminal is designed predominantly for use in new build situations where the roof construction allows for ridge penetration. In retrofit installations roofing materials will need to be removed/replaced and the roof structure may require
© Baxi Heating UK Ltd 2011 Twin Pipe Flue System Examples FLUE OPTIONS The MAXIMUM total equivalent length is stated in the Installation & Servicing Instructions supplied with each boiler. 1m Min to 15m Max The total equivalent length for this example is = 6.5 metres. 1m extension 135°bend 91.5°bend 1m 0.25m 0.5m 5 2 2 5.0m 0.5m 1.0m AIR DUCT No of fittings/pipes Sub total Equivalent Length Value Equivalent Length Air Duct = 6.5m 1m extension 13

Baxi Kitchen Appliances Owners Instructions: