MSD Ignition 4242 Installation Instruction

Text of MSD Ignition 4242 Installation Instruction

MSD IGNITION • 12120 ESTHER LAMA, SUITE 114, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 858-9241

MSD Watercraft Ignition System PN 4242, 4243, 4244 IMPORTANT: Read these Instructions before attempting the installation! Tools Required 1 - 4mm Allen Wrench 1 - Phillips Screw Driver 1 - 1/2" Drive Rachet 1 - 1/2 x 30mm Socket (Sea Doo Only) 1 - 1/2 x 14mm Socket (650/750 Kaw. Eng. Only) 1 - 1/2 x 17mm Socket (650/701 Yam. Eng. Only) 1 - Torque Wr
MSD IGNITION • 12120 ESTHER LAMA, SUITE 114, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 858-9241 For ease of installation, these instructions are divided into sections. Section I: Mounting the Ignition, Coil and Starter Relay Section II: Installing the Spark Plug Wires Section III: Installing the Flywheel and Trigger Pickup Assembly Section IV: Wiring the Ignition System, Cable Identification, Connecting the Power
MSD IGNITION • 12120 ESTHER LAMA, SUITE 114, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 858-9241 The following are suggested areas to install the mounting plate to your craft. Kawasaki 650 SX Remove the stock electrical box and mount the plate to existing mounting bosses. Kawasaki X2 Attach ignition mounting plate under the hood latch mounting bolts. Mount coil above engine next to the steering arm. Kawasaki 750 SX,
MSD IGNITION • 12120 ESTHER LAMA, SUITE 114, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 858-9241 Figure 7 Postioning the Terminal in the Boot. Figure 6 Installing the Wire and Crimping. 5. After positioning the conductor, position the terminal/wire assembly into the "W" groove side of the Mini-Crimper. Align the tabs so they are exactly centered on the point (Figure 6). 6. Slide the stripper block over the crimping
MSD IGNITION • 12120 ESTHER LAMA, SUITE 114, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 858-9241 Figure 9 Mounting the Trigger Plate Assembly. Figure 8 Assembling the Trigger Plate. Figure 10 Modifying the Kawasaki 750 Case. SECTION III FLYWHEEL AND TRIGGER PLATE REMOVAL Before installing the MSD Flywheel and Trigger Pickup assembly, the stock magneto flywheel and stator plate must be removed. Refer to your craft
MSD IGNITION • 12120 ESTHER LAMA, SUITE 114, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 858-9241 Figure 11 Checking the Air Gap. CHECKING THE AIR GAP It is important to have the correct air gap between the pickup and the flywheel. Too much may not trigger the ignition while too little may cause contact to the pickup. 1. Position a small amount of clay on the top of the trigger pickup (Figure 11). 2. Place the flywhe
MSD IGNITION • 12120 ESTHER LAMA, SUITE 114, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 858-9241 Figure 14 Installing Perma-Seal Connectors. SECTION IV WIRING All wires must be routed to the locations described, then cut to length and have Perma-Seal solderless connectors installed as shown in Figure 14. Applying a small amount of heat to the connector seals the wire to terminal connection. MSD CABLE IDENTIFICATIO
MSD IGNITION • 12120 ESTHER LAMA, SUITE 114, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 858-9241 Note:It does not matter which Green wire on the ignition is hooked to which Green wire on the trigger pickup. CONNECTING THE FACTORY STOP SWITCH PN 4272: To retain use of the factory stop switch located on the handle bar, attach the two wires coming from the stop switch to the two GREEN wires from the MSD Ignition (Figur
MSD IGNITION • 12120 ESTHER LAMA, SUITE 114, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 858-9241 Figure 19 Finding Top Dead Center. SECTION V TIMING AND PROGRAMMING The MSD Watercraft Ignitions innovative design allows you to static time the engine before the engine is started. Study the special features shown in Figure 18 before proceeding. Figure 19 How to Check Static Timing At this point in the installation, the
MSD IGNITION • 12120 ESTHER LAMA, SUITE 114, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 858-9241 retard the timing up to 7° less than what the maximum true timing is set at. Always set the trigger plate for the maximum amount of timing the engine will ever run at. 5. To adjust the ignition's max timing the trigger plate must be rotated counter-clockwise to advance the timing or clockwise to retard the timing. To
MSD IGNITION • 12120 ESTHER LAMA, SUITE 114, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 858-9241 FACTOR ADVANCE FOR RETARD FOR Cylinder Pressure Low High RPM Engine Low High Energy of Ignition Low High Fuel Octane High Low Mixture (Fuel/Air) Rich Lean Temperature Cool Hot Combustion Turbulence Low High Load Light Heavy As you can see from the chart, most factors will change throughout the range of engine operatio
MSD IGNITION • 12120 ESTHER LAMA, SUITE 114, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 858-9241 INITIAL TIMING: INITIAL TIMING: INITIAL TIMING: INITIAL TIMING: INITIAL TIMING: The LED indicated timing is 5° advanced from the actual run timing, if switch 1 is set to on/on/ on. Refer to Section V "Timing the Watercraft Ignition" for proper setting. SET SET SET SET SETTING MAX TIMING: TING MAX TIMING: TING MAX TIMIN
MSD IGNITION • 12120 ESTHER LAMA, SUITE 114, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 858-9241 SUGGESTED PROGRAMMING POINTS ENGINE RPM RETARD BEGIN RETARD REV/RETARD LIMIT 650/750 Kaw. 5000-6000 3800-4200 RPM 8° 7000 RPM 650/750 Kaw. 6000-7000 4600-5000 RPM 7° 8000 RPM 650/750 Kaw. 6600-7600 5000-5600 RPM 7° 9000 RPM 650/701/760 Yam. 5000-6000 3800-4200 RPM 8° 7000 RPM 650/701/760 Yam. 6000-7000 4600-5000 RPM
MSD IGNITION • 12120 ESTHER LAMA, SUITE 114, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 858-9241 SECTION VI TROUBLESHOOTING After installing the MSD Ignition System, if the craft fails to start, check the installation procedure for any missed steps. If everything checks correctly, inspect the following: 1. Check the battery to make sure it is fully charged and properly connected. Also make sure the terminal connec
MSD IGNITION • 12120 ESTHER LAMA, SUITE 114, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 858-9241 TECH NOTES _______________________________________________________________________________ _______________________________________________________________________________ _______________________________________________________________________________ ______________________________________________________________________

MSD Ignition 4242 Printed In U.S.A.

Limited Warranty Autotronic Controls Corporation warrants MSD Ignition products to be free from defects in material and workmanship under normal use and if properly installed for a period of one year from date of purchase. If found to be defective as mentioned above, it will be replaced or repaired if returned prepaid along with proof of date of purchase. This shall constitute the sole remedy of the purchaser and

MSD Ignition Motorcycle Accessories Owners Instructions: