PEERLESS PRS-EXA Installation And Assembly Manual

ISSUED: 04-24-08 SHEET #: 055-9256-1 Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870. � This product is intended for use with UL Listed products and must be installed by a qualified professional installer. Installation and Assembly: Projector Ceiling/Wall Mount Installed to Ceiling Installed to Wall (PRS-EXC models are not wall mountable due to its extensive reach) 3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com Maximum UL Load Capacity: 25 lb (11.3 kg) Models: PRS-EXA, PRS-EXA-S, PRS-EXA-W PRS-EXB, PRS-EXB-S, PRS-EXB-W PRS-EXC, PRS-EXC-S, PRS-EXC-W Features: • Continuous channel design for uninterrupted drop length or wall extension adjustments • Safety catch designed into extension to ensure user and equipment safety • Internal cable management within channels for clean, clutter-free appearance • Includes PRS Series projector mount for precise image alignment

ISSUED: 04-24-08 SHEET #: 055-9256-1 Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870. Note: Read entire instruction sheet before you start installation and assembly. Tools Needed for Assembly • stud finder ("edge to edge" stud finder is recommended) • drill • phillips screw driver • 1/4" bit for concrete and cinder block wall • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112. • This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions. • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard- ware and components. • Never exceed the Maximum UL Load Capacity. See page 1. • If mounting to wood ceiling/wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an "edge to edge" stud finder is highly recommended. • Always use an assistant or mechanical lifting equipment to safely lift and position equipment. • Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power. • This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury. • This product was designed and intended to be mounted to the following supporting surfaces checked below with the hardware included in this product as specified in the installation sheet. To mount this product to an alternative support- ing surface, contact Peerless customer care at 1 800 865-2112. • This product was designed to be installed on the following ceiling/wall construction only; CEILING/WALL CONSTRUCTION ADDITIONAL HARDWARE REQUIRED x Wood Stud None x Wood Joist None x Solid Concrete None x Cinder Block None Metal Stud Do not attach except with Peerless accessory kit for metal studs; Contact Customer Service for Peerless accessory kit for metal studs. Brick Contact Customer Service Other or unsure? Contact Customer Service WARNING • open end wrench • 5/32" bit for wood stud or joist • level • 8 mm open end wrench Table of Contents Parts List ........................................................................................................................................................................... 3-4 Installing Outer Channel to Ceiling Plate ............................................................................................................................... 5 Installation to Wood Joist Ceiling or Wood Stud Wall ........................................................................................................... 6 Installation to Solid Concrete Ceiling or Concrete/Cinder Block Walls .................................................................................. 7 Installing Inner Channel and Routing Cables ......................................................................................................................... 8 Installing Projector Mount ................................................................................................................................................ 9-10 Attaching Adapter Plate to Projector.............................................................................................................................. 10-11 Projector Alignment ............................................................................................................................................................ 12 Adjusting Mount Extension ................................................................................................................................................. 13 Installing Cable Covers ........................................................................................................................................................ 13

ISSUED: 04-24-08 SHEET #: 055-9256-1 Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870. extendable outer channel (B) inner channel (C) cable cover (Q) Model# length part# part# part# PRS-EXA 8.69" - 12.79" 055-1779 055-1778 055-1809-2 PRS-EXA-S 8.69" - 12.79" 055-4779 055-4778 055-4809-2 PRS-EXA-W 8.69" - 12.79" 055-2779 055-2778 055-2809-2 PRS-EXB 12.69" - 20.69" 055-1776 055-1775 055-1809-1 PRS-EXB-S 12.69" - 20.69" 055-4776 055-4775 055-4809-1 PRS-EXB-W 12.69" - 20.69" 055-2776 055-2775 055-2809-1 PRS-EXC 19.14" - 32.9" 055-1770 055-1769 055-1809 PRS-EXC-S 19.14" - 32.9" 055-4770 055-4769 055-4809 PRS-EXC-W 19.14" - 32.9" 055-2770 055-2769 055-2809 OUTER CHANNEL, INNER CHANNEL AND CABLE COVER PART NUMBER CHART Parts List PRS-EXA PRS-EXB PRS-EXA-S PRS-EXB-S PRS-EXA-W PRS-EXB-W PRS-EXC PRS-EXC-S PRS-EXC-W Description Qty. Part # Part # Part # Part # Part # Part # A projector mount assembly 1 055-0604 055-0605 055-0606 055-0604 055-0605 055-0606 B adapter plate 1 055-0619 055-0620 055-0621 055-0619 055-0620 055-0621 C #14 x 2.5 phillips hex head wood screw 2 5S1-015-C03 5S1-015-C04 5S1-015-C04 5S1-015-C03 5S1-015-C04 5S1-015-C04 D concrete anchor 2 590-0097 590-0097 590-0097 590-0097 590-0097 590-0097 E #10-32 x 1/4" socket pin screw 1 520-1196 520-2196 520-2196 520-1196 520-2196 520-2196 F 1/4" flat washer 6 540-1078 540-1078 540-1078 540-1078 540-1078 540-1078 G M3 x 8 mm socket pin serrated washer head screw 4 510-1004 510-2004 510-2004 510-1004 510-2004 510-2004 H M4 x 10 mm socket pin serrated washer head screw 4 510-1060 510-2060 510-2060 510-1060 510-2060 510-2060 I M5 x 10 mm socket pin serrated washer head screw 4 510-1126 510-2063 510-2063 510-1126 510-2063 510-2063 J M6 x 10 mm socket pin serrated washer head screw 4 510-1066 510-2066 510-2066 510-1066 510-2066 510-2066 K #6 flat washer 4 540-1025 540-2025 540-2025 540-1025 540-2025 540-2025 L 4 mm security t-wrench 1 560-1718 560-1718 560-1718 560-1718 560-1718 560-1718 M 2 mm security allen wrench 1 560-1097 560-1097 560-1097 560-1097 560-1097 560-1097 AA ceiling plate 1 055-1773 055-4773 055-2773 055-1773 055-4773 055-2773 BB outer channel 1 SEE CHART SEE CHART SEE CHART SEE CHART SEE CHART SEE CHART CC inner channel 1 SEE CHART SEE CHART SEE CHART SEE CHART SEE CHART SEE CHART DD clamp plate 1 055-1771 055-4771 055-2771 055-1771 055-4771 055-2771 EE vertical mounting plate 1 055-1796 055-4796 055-2796 055-1796 055-4796 055-2796 FF horizontal mounting plate 1 055-1787 055-4787 055-2787 N/A N/A N/A GG M5 x 16 mm socket pin screw 2 520-1161 520-2161 520-2161 520-1161 520-2161 520-2161 HH M6 x 12 mm socket pin screw 2 520-1050 520-2050 520-2050 520-1050 520-2050 520-2050 II M6 x 10 mm socket pin screw 4 520-1066 520-2066 520-2066 520-1066 520-2066 520-2066 JJ M5 x 10 mm socket pin screw 4 520-1063 520-2063 520-2063 520-1063 520-2063 520-2063 KK serrated locknut 2 530-1027 530-2042 530-2042 530-1027 530-2042 530-2042 LL cable cover 2 SEE CHART SEE CHART SEE CHART SEE CHART SEE CHART SEE CHART

ISSUED: 04-24-08 SHEET #: 055-9256-1 Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870. I Note: Actual parts may appear slightly different than illustrated. C D E F J K G H AA BB CC DD EE FF GG HH II JJ KK LL A B M L

ISSUED: 04-24-08 SHEET #: 055-9256-1 Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870. Install Outer Channel to Ceiling Plate Attach outer channel (BB) to ceiling plate (AA) using four M6 x 10 mm socket pin screws (II) as shown. Tighten screws with 4 mm security wrench (L). AA BB II 1

ISSUED: 04-24-08 SHEET #: 055-9256-1 Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870. Installation to Wood Joist Ceilings or Wood Stud Walls NOTE: Wall installation with models PRS-EXC, PRS-EXC-S and PRS-EXC-W is not available. Use a stud finder to locate the edges of the stud or joist. Use of an edge-to-edge stud finder is highly recommended. Based on its edges, draw a vertical line down the stud's or joist’s center. Place ceiling/wall plate (AA) on wall or ceiling as a template, making sure that the two mounting slots are on the centerline. For ceiling installation: Opening on outer channel (BB) indicates front of mount. Use the correct mounting slots on the ceiling/wall plate depending on ceiling joist orientation as shown in figure 2.1 and figure 2.2. Mounting slots on ceiling plate allow for 45° (±22.5) of rotation before securing to joist. For wall installation: Opening on outer channel (BB) indicates top of mount. Mark the center of the two mounting holes. Drill two 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Secure ceiling/wall plate (AA) to wood stud or joist using two #14 x 2-1/2" wood screws (C) and two 1/4" washers (F) as shown. Skip to step 3 • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that ceiling/wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. • Never tighten in excess of 80 in. • lb (9 N.M.). • Make sure that mounting screws are anchored into the center of the stud or joist. The use of an "edge to edge" stud finder is highly recommended. • Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs or joists. Installers are responsible to provide hardware for other types of mounting situations (not UL approved). WARNING 2 AA C BB OPENING ON OUTER CHANNEL (BB) INDICATES TOP OF MOUNT fig. 2.3 WOOD JOIST fig. 2.2 C AA OPENING ON OUTER CHANNEL (BB) INDICATES FRONT OF MOUNT C AA BB BB WOOD STUD fig. 2.1 CEILING INSTALLATION WALL INSTALLATION (EXCEPT FOR PRS-EXC MODELS) MOUNTING SLOTS ALLOW FOR ROTATION BEFORE SECURING TO JOIST F F F

ISSUED: 04-24-08 SHEET #: 055-9256-1 Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870. Installation to Concrete Ceilings or Concrete/Cinder Block Walls • Always attach concrete expansion anchors directly to load-bearing concrete. • Never attach concrete expansion anchors to concrete covered with plaster, drywall, or other finishing mate- rial. If mounting to concrete surfaces covered with a finishing surface is unavoidable, the finishing surface must be counterbored as shown below. Be sure concrete anchors do not pull away from concrete when tightening screws. If plaster/drywall is thicker than 5/8" (16 mm), custom fasteners must be sup- plied by installer (not UL approved). WARNING NOTE: Wall installation with models PRS-EXC, PRS-EXC-S and PRS-EXC-W is not available. Place ceiling/wall plate (AA) on ceiling or wall as a template. Note: Place ceiling/wall plate according to position of opening in outer channel (BB) as shown in figure 2.4. or figure 2.5. Drill two 1/4" (6 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach ceiling/ wall plate (AA) using two concrete anchors (D), two #14 x 2.5" wood screws (C) and two 1/4" washers (F) as shown in figure 2.6. Tighten wood screws (C) until ceiling/wall plate (AA) is firmly attached. CUTAWAY VIEW INCORRECT concrete plaster/ dry wall CORRECT concrete plaster/ dry wall • Tighten wood screws firmly, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. • Never tighten in excess of 80 in • lb (9 N.M.). WARNING 2 AA AA concrete surface 1 3 2 D Drill holes and insert anchors (D). Place plate (AA) over anchors (D) and secure with washers (F) and screws (C). Tighten all fasteners. AA D C • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity. • Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. WARNING D BB AA C C BB AA D OPENING ON OUTER CHANNEL (BB) INDICATES FRONT OF MOUNT CONCRETE CEILING CONCRETE WALL CINDER BLOCK WALL OPENING ON OUTER CHANNEL (BB) INDICATES TOP OF MOUNT fig. 2.4 fig. 2.5 fig. 2.6 CEILING INSTALLATION WALL INSTALLATION (EXCEPT FOR PRS-EXC MODELS) F F F

ISSUED: 04-24-08 SHEET #: 055-9256-1 Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870. Installing Inner Channel and Routing Cables 3 Note: Be certain holes on inner channel (CC) face in the same direction of opening on outer channel (BB). Note: Cables must be removed from projector before routing through channels. If cables are not removable from projector, routing through channels is not an option. Guide projector cables into openings in channels then insert inner channel (CC) into outer channel (BB) as shown in figure 3.1 or 3.3. Position inner channel (CC) to the desired extended position and secure using two M6 x 12 mm socket pin screws (HH) through clamp plate (DD) and into inner channel (CC) as shown in figure 3.2 or 3.4. CEILING INSTALLATION WALL INSTALLATION (EXCEPT FOR PRS-EXC MODELS) OPENING HOLES BB CC fig. 3.4 fig. 3.3 HH DD BB CC OPENING BB CC HOLES GUIDE CABLES IN CHANNELS fig. 3.1 fig. 3.2 HH DD BB CC

ISSUED: 04-24-08 SHEET #: 055-9256-1 Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870. Installing Projector Mount 4 Installing PRS projector mount with ceiling installation: Attach vertical mounting plate (EE) to PRS projector mount (A) using two M5 x 16 mm socket pin screws (GG), two flat washers (F) and two locknuts (KK) as shown in figure 4.1. Installing PRS projector mount with wall installation: Position PRS projector mount (A) to the orientation shown in figure 4.2 and attach to horizontal mounting plate (FF) using two M5 x 16 mm socket pin screws (GG), two flat washers (F) and two locknuts (KK). Note: Placing screws (GG) and washers (F) through slots on inside of PRS projector mount and attaching horizontal mounting plate from the bottom can make installation easier as shown in figure 4.3. CEILING INSTALLATION KK F GG EE HOLE INDICATES FRONT OF MOUNT WALL INSTALLATION (EXCEPT FOR EXC MODELS) HOLE INDICATES FRONT OF MOUNT KK F GG FF fig. 4.1 fig. 4.2 fig. 4.3 PLACE SCREWS (GG) AND WASHERS (F) FIRST GG F A A A 5 Ceiling installation: Insert vertical mounting plate (EE) into inner channel (CC) with projector mount (A) in the correct orientation shown in figure 5.1. Secure vertical mounting plate to inner channel using four socket pin screws (JJ) as shown in figure 5.2. fig. 5.1 CC EE HOLE INDICATES FRONT OF MOUNT A fig. 5.2 JJ EE CC

ISSUED: 04-24-08 SHEET #: 055-9256-1 Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870. Wall installation: Insert horizontal mounting plate (FF) into inner channel (CC) as shown in figure 5.3. Secure horizontal mounting plate to inner channel using four socket pin screws (JJ) as shown in figure 5.4. 5 fig. 5.3 FF CC HOLE INDICATES FRONT OF MOUNT fig. 5.4 FF JJ CC Generic Projector Place projector upside down. Locate adapter plate (B) with notch facing forward as close to projector center of gravity as possible without covering any mounting holes. Loosen channels with 4 mm security allen wrench (I), and if there are only three mounting holes remove fourth channel. Using one channel for each mounting hole, position feet of channels over mounting holes as shown below. Important: If projector does not have at least three mounting holes, do not use this adapter plate. Note: Some projectors have feet which can be removed and the corresponding threaded insert can be used for a mounting hole. Note: Once channels are in position retighten fasteners. *Notch indicates front of projector. Note: The projector you are installing may differ in appearance from the sample illustrated below. * Mounting hole 6 Channel Foot of Channel Attaching Adapter Plate to Projector B

ISSUED: 04-24-08 SHEET #: 055-9256-1 Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870. Attach adapter plate (B) to projector using one screw (G, H, I, or J) for each channel as shown below. Tighten all screws, while keeping the center of gravity. Be sure that adapter plate (B) is straight. Adjust the feet of the channels to keep the adapter plate level. Tighten all screws with 4 mm security allen wrench (L) while keeping the center of gravity. If M3 x 8 mm screws (G) are used, tighten using 2 mm security allen wrench (M). Note: Projectors will require different size screws for mounting. Use a combination of screws (G, H, I, or J) and foot adjustment that will result in channels of adapter plate (B) fitting tightly against projector. Important: In order to properly engage the threads in the mounting holes, the screw must be turned at least 3 full turns. Note: If using screw (G), place washer (K) between screw (G) and foot of channel. • It is the responsibility of the installer to ensure that the projector is properly ventilated. Feet of channels are used to raise the mount off the projector surface. CAUTION G, H, I, or J 7 B FOOT OF CHANNEL Slide connection block with projector into projector mount assembly (A) as shown. Push in and tighten captive screw to secure projector to projector mount assembly (A). CONNECTION BLOCK A CAPTIVE SCREW FRONT OF MOUNT • Always use an assistant or mechanical lifting equipment to safely lift and position the projector. WARNING 8 FRONT OF MOUNT Attaching Adapter Plate to Projector EE or FF

ISSUED: 04-24-08 SHEET #: 055-9256-1 Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870. To adjust yaw (swivel): Loosen screw on projector mount assembly (A) indicated below until projector mount can be rotated. Rotate mount to desired position and retighten screw. To adjust pitch (forward and backward tilt): Using 4 mm security t-wrench (L) (security adjustment models) or a phillips screwdriver (non-security adjustment models), loosen two screws for pitch adjustment on projector mount assembly (A) indicated below. Tilt mount to desired position and retighten screws. To adjust roll (side to side tilt): Using 4 mm security t-wrench (L) (security adjustment models) or a phillips screwdriver (non-security adjustment models), loosen two screws for roll adjustment on projector mount assem- bly (A) indicated below. Tilt mount to desired position and retighten screws. Projector Alignment 20° (±10°) SWIVEL SWIVEL ADJUSTMENT TOP VIEW 10 MOUNT ASSEMBLY NOT SHOWN FOR CLARITY IMPORTANT: For security installations, insert one #10-32 x 1/4" socket pin screw (E) through projector mount assembly (A) and into connection block as shown. Tighten screw with 4mm security t-wrench (L). 9 CONNECTION BLOCK A E A SCREWS FOR PITCH ADJUSTMENT SCREW FOR SWIVEL STOP SCREWS FOR ROLL ADJUSTMENT • Do not loosen adjustment screws to the point they become disengaged from the mount. Weight of the projector should be supported in case of accidental disengagement. WARNING

ISSUED: 04-24-08 SHEET #: 055-9256-1 Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870. 11 CEILING INSTALLATION WALL INSTALLATION (EXCEPT FOR EXC MODELS) DD DD Adjusting Mount Extension • On ceiling installations, clamp plate adjustment screws support weight of projector when fully tightened. Weight of the projector will need to be supported if clamp plate screws are loosened. WARNING While supporting the weight of the projector, loosen clamp plate screws half a turn and position projector to the desired extended position. Retighten clamp plate screws securely. CLAMP PLATE SCREWS CLAMP PLATE SCREWS Cut cable covers (LL) to the length of inner channel (CC) and outer channel (BB) openings, leaving space for cables if routed through channels. Snap cable covers (LL) into openings as shown. 12 CABLES CUT TO LENGTH OF OPENING LL CUT TO LENGTH OF OPENING LL CABLES CEILING INSTALLATION WALL INSTALLATION (EXCEPT FOR EXC MODELS) CUT TO LENGTH OF OPENING LL CUT TO LENGTH OF OPENING LL BB CC BB CC Install Cable Covers © 2008, Peerless Industries, Inc. All rights reserved. All other brand and product names are trademarks or registered trademarks of their respective owners.