LOGICDATA HSU Operation & User’s Manual

Text of LOGICDATA HSU Operation & User’s Manual

Cable Handswitch for installation below the

desktop HSU Rev 3 Subject to change without notice. Errors and omissions excepted. LOGICDATA cannot accept responsibility for incorrect operation or use of the products other than for the intended purpose. Under the warranty terms, LOGICDATA shall replace or repair any products that prove defective at the time of delivery. LOGICDATA shall not assume any further liability. If you have any questions or

Page 2 / 11

Contents 1. Preface................................................................................................................ 3 2. General................................................................................................................ 3 2.1 Intended Use................................................................................................ 3 2.2 Definition ...........................................................

Page 3 / 11

1. Preface Dear customer, Thank you for choosing a HSU – cable-handswitch by LOGICDATA Electronic & Software Entwicklungs GmbH. You have purchased a state-of-the-art product. 2. General 2.1 Intended Use The HSU cable-handswitch must be used with LOGICDATA control boxes. The control box must be installed, initially operated and functional tested by competent personnel only. Use other than described above is only allowed with permission of LOGI

Page 4 / 11

2.4 Package Contents The HSU cable-handswitch package contains: 1 2 3 Figure 1: Package contents � HSU cable-handswitch � mounting plate � screws Danger: Use only genuine replacement parts! Repairs must be carried out only by a qualified service technician! If you neglect to do so you void your warranty! 2.5 Overview Desk upwards Desk downwards Display Memory button Position button 1 Position button 2 Position button 3 Position button 4 F

Page 5 / 11

Desk upwards Desk downwards Display Figure 3: HSU-MDF-2-LD Desk downwards Desk upwards Figure 4: HSU-OD-2-LD

Page 6 / 11

2.6 Handswitch Plug Pin assignment Handswitch connector 3 2 1 5 4 7 6 (pin alignment according to DIN 45329) Caution: The HSU handswitch is only suitable for LOGICDATA motor controls. To prevent damage of the unit, take care not to interchange handswitch and motor sockets. Colour code: Handswitch: blue Motor: black 3. Mounting Instructions Mount the HSU cable-handswitch underside your desktop in an appropriate position. Following tools are requ

Page 7 / 11

4. Connect the handswitch to the control box using the jack marked with only! Do not connect the handswitch plug to the motor jacks! Caution: Unplug the power cord of the control unit while mounting the handswitch! Figure 5: Connect the HSU cable-handswitch to the control box (e.g. COMPACT)

Page 8 / 11

4. Functions The HSU cable-handswitch is capable of a wide range of functions, which are described below. 4.1 Display The display of the HSU cable-handswitch consists of a 3 digit position and information display. 4.2 Basic Functions Function Description Note Desk upwards For an upward adjustment of the desk push this button. Push this button until the desired height of the desk has been reached. The desk will continue driving upwards until you

Page 9 / 11

4.3 Advanced Functions 4.3.1 Storing a position Using this function you are able to store a desktop position. Note: On initial operation all stored positions are equal to the lowest possible desk-height (lower end position). Note: Only one desk-height per button is allowed. 1. Move the desk to the position you want to store. The display reads the actual height of the desk (e.g. 73cm). 2. Press the S button. The display reads S –. 3. Press

Page 10 / 11

Alternative B (using double click automatic function) 1. Double-click the desired position button (e.g. 2) 2. The desk automatically moves to the saved position. If you press any button before reaching the saved position, the desk stops and the saved position will not be reached. The display reads the actual desk-height. 5. Technical Data Supply voltage 5VDC ± 10% Current consumption (average) 75 mA Life cycle (switching cycles) 10. 000 Ambi

LOGICDATA Indoor Furnishing Owners Instructions: