GEZE Hook bolt Lock A Installation Instructions Manual

2  Contents 1 Introduction...............................................................................................................................................................3 1.1 Symbols and illustrations...............................................................................................................................................................................3 1.2 Revisions and validity......................................................................................................................................................................................3 1.3 Product liability................ ...

3 Introduction 1 Introduction 1.1 Symbols and illustrations Warning notices In these instructions, warnings are used to warn against material damage and injuries. X X Always read and observe these warnings. X X Observe all measures marked with the warning symbol and warning word . Warning symbol Warning word Meaning WARNING Danger for individuals. Non-compliance can result in death or serious injuries. More symbols and illustrations Important information and technical notes are highlighted to explain correct operation. Symbol Meaning means “important note”. Information to prevent property damage, to understand or optimise the opera ...

4 Fundamental safety precautions 1.5 Abbreviations HSK Main closing edge OKFF Finished floor level 2 Fundamental safety precautions To ensure personal safety, it is important to follow these safety instructions. These instructions must be kept. 2.1 Intended use The hook bolt locks A are only suitable for use àà in dry rooms àà in automatic door systems for horizontal door leaves àà in entrances and interior areas of pedestrian traffic in commercial plants and public areas The hook bolt locks must not be used in fire and smoke protection doors. 2.2 Safety notices àà The mandatory installation, maintenance and repair work must be ...

5 Overview àà Danger of injury caused by unsecured crushing, impact, drawing-in or shearing spots. àà Danger of injury due to broken glass. àà Danger of injury due to sharp edges in the drive. àà Danger of injury during installation through freely moving parts. 2.4 Inspection of the installed system Measures for protection and prevention of pinching, impact, shearing or drawing-in spots: àà Check the function of safety sensors and movement detectors. àà Check protective earth connection to all metal parts that can be touched. àà Perform a safety analysis (risk analysis). 2.5 Environmentally conscious working àà When dis ...

6 Overview 3.2 Tools and aids Tool Size/remark Tape measure Marking pen Torque spanner Allen key 1.5 mm; 2.5 mm; 4 mm; 5 mm Open-ended spanner 8 mm; 10 mm; 13 mm; 15 mm Ring spanner 8 mm; 10 mm Screwdriver set Slotted up to 6 mm, cross-slot PH2 or PZ2 Torx spanner T × 20; T × 25 Side-cutting pliers Crimping pliers for cables Wire stripper Multimeter Installation tool Lock A Mat. no. 153719 Cable ties 2.5 × approx. 100 Metal drill Ø 2.8 mm 3.3 Torques The torques are given in the specific installation step, the drive drawing and the leaf drawings. ...

7 Installation 4 Installation 4.1 Installing hook bolt lock A in the side screen profile 4.1.1 Install the strike plate in the side screen (1- and 2-leaf)    ...

8 Installation 4.1.2 Install the drive and hook bolt locks in the side screen bolts The hook bolt locks are available in versions with single or double locking. The illustration below shows the ver- sion with double locking in the locked state.   1 Side screen bolt 2 Upper hook bolt lock 3 Connecting link arm 4 Holder 5 Drive hook bolt lock 6 Lower hook bolt lock Factory setting The side screen bolts are delivered unlocked. ...

9 Installation Preparation for installation – version with one hook bolt lock 1.5 Nm ...

10 Installation Preparation for installation – version with two hook bolt locks 1.5 Nm ...

11 Installation Installing the hook bolt locks X X Push the connecting link arm in until the marking can be seen as shown in the diagram on the right. The optimum position for the installation of the hook bolt locks has then been reached. X X When installing two hook bolt locks make sure that the hooks of the driving rod catch the connecting link arm as shown below (see arrows). 2.5 Nm 2.5 Nm ...

12 Installation Attaching the rubber seals (illustration with 2 hook bolt locks) 4.2 Installing the transmission element with ECdrive 4.2.1 ECdrive, 1-leaf, right hand slide to open X X Adjust the position of the stop buffer in closed position without rubber buffer after door installation and calibration. When the door is closed the stop buffer must not be flush. The distance should be about 1 mm. Installing the spring-mounted unit ...

13 Installation Installing the unit without spring-mounting     X X Move the moving leaf towards the closed position. Closed position Open position ...

15 Installation 4.2.2 ECdrive, 1-leaf, left hand slide to open, 2-leaf X X Adjust the position of the stop buffer after door installation and calibration. When the door is closed the stop buffer must not be flush. The distance should be about 1 mm. With 2-leaf systems: X X Install 2 additional stop buffers before installing the roller carriage in the centre of the system. X X Install the stop buffers (3) in such a way that the rubber buffers (2) are not pointing towards the roller carriage (1). or X X Install the stop buffers on the main closing edge without rubber buffers. The additional stop buffers protect the contacts when the door ...

16 Installation Installing the unit without spring-mounting     X X Move the moving leaf towards the closed position. Open position Closed position ...

18 Installation 4.3 Installing the transmission element with ECdrive T2 4.3.1 ECdrive T2, 1-leaf, right hand slide to open X X Adjust the position of the stop buffer in closed position without rubber buffer after door installation and calibration. When the door is closed the stop buffer must not be flush. The distance should be about 1 mm. Installing the spring-mounted unit X X Screw the spring-mounted unit (1) to the buffer (2). 1 2 Installing the unit without spring-mounting     ...

19 Installation X X Move the moving leaf towards the closed position. Closed position Open position  Closed position ...

20 Installation 4.3.2 ECdrive T2, 1-leaf, left hand slide to open, 2-leaf Installing the spring-mounted unit X X Screw the spring-mounted unit (1) to the buffer (2). 1 2 ...