Engl E610II Operator's Manual

Text of Engl E610II Operator's Manual

A FEW WORDS FROM THE AMP DESIGNER

„The SAVAGE tube amp heads are among the most popular amps in the ENGL product range and the SAVAGE 120 head equipped with a few brand new unique features has set new standards in the early nine- ties concerning guitar tube amp technology. For the SAVAGE Mark II series I have undertaken big efforts during the R&D phase in order to usefully enhance some of the proven features to a top notch level. Furt- hermore I equipped

The Engl Savage Mark II is the reincarnation of the legandary Engl Savage 120. With many great impro-

vements and additional functions you now own one of the most advanced versatile amp heads available today! This sophisticated guitar amp marries the unrivalled tone of all-tube technology to the awesome sound-shaping might of control features powered by state-of-the-art microchip circuitry. This elegant combination puts at your fingertips a va

The PRESHAPE filter lowers a certain mid range spectrum thus the lower end and the upper frequency

range gets emphasized stronger when this function is activated. The Preshape sound option can also be switched via MIDI program change, MIDI Controller #21, or the ENGL Z9. The red LED above the button lights up to indicate when PRESHAPE is activated. A TIP FROM THE DESIGNER: this pecisely tuned preshape filter system is ideally suited to infl

This is the preamp voicing section´s passive high-frequency EQ for Clean and Crunch I.

Mid Le./Bo. Switch With this button you can select one of the two mid range controls MID LEAN or MID BOLD. The MID BOLD control knob is selected at the activated MID LE./BO. function. The red LED above this button lights up to indicate the MID LE./BO. function is on; i.e. the MID BOLD control knob is currently controlling the mid range. The MID LE./BO. switching

Engl E610II Noise Gate Switch

Press this button to activate an onboard and suppress excess noise in Crunch I, Crunch II and Lead chan- nels. Control the Noise Gate using the Level Threshold knob on the back of the amp. The LED above the button lights up to indicate the Noise Gate is activated. Note that the Noise Gate does not operate during the Clean channel is selected. This feature can also be switched via MIDI program change MIDI Controller #24, or the ENGL Z9. IM

channels Crunch I, Crunch II and Lead at high Gain levels is to set the Threshold knob higher than 12 o‘clock.

If you‘re doing the low-gain thing in Lo Gain mode, dial in a lower Threshold setting (below 12 o‘clock) to prevent the gate from throttling notes (that is, the musically useful sounds) as they decay, particularly if you like to work the guitar‘s volume knob. Presence A Power amp Presence A knob. This knob determines the power amp‘s high

Engl E610II Gain control for the Lead Channel. This knob determines the preamp‘s input sensitivity when Lead Channel

is selected and, by extension, the preamp signal´s saturation level. Contour Switch The CONTOUR feature alters some parameters and the efficiency of the EQ system in CRUNCH II / LEAD and mainly becommes audible in the lower mid range area between 300 and 700 Hz and to some degree in the upper frequency range between 1.5 and 3 KHz. Activate

to go for vintage tube tone and for playing solos. This sound character is ideally suited to push your guitar

tone through in the musical event. Crunch II Vol. Volume control for the Crunch II Channel (pre-FX Loop, influences the send level). Use this knob to dial in the desired balance of levels with Channels Clean, Crunch I and the Lead Channel. Crunch II Switch Press this button to activate preamp Crunch II Channel at the amp. The yellow LED to the righ

MORE GOOD TO KNOW INFO:

Note that the Status LED also indicates the status of components unrelated to WRITE and COPY. The micro- controller runs a short system check after you switch the amp on. Should it find a defect in the memory chip (EEPROM), the LED will flash in a pattern of five short bursts. Press the WRITE/COPY button to confirm that you got the message. Once you have done this, the system will be ready to run, although you may encounter problems

Stand By Switch

Power amp Stand By switch: Use this switch to protect the power tubes against wear (0 position) when you take a longer break. The amp‘s tubes stay nice and toasty, and the amp is ready to roll immediately when you ramp it back up to full power. Activates as soon as you set the Stand By switch to the 0 position. Power Switch Mains power on/off. PLEASE NOTE: ensure that the Stand By is set to Stand By (0 position) before you switch the amp

Main Supply Connector (AC Power Inlet, IEC – C14 connector)

Plug the mains cord in here. CAUTION: Make sure you use an intact mains line cord with a grounded plug! Before you power the amp up, ensure the voltage value printed alongside the mains port is the same as the current of the local power supply or wall outlet. Please also heed the guidelines set forth in the separately included pamphlet, Instructions for the Preven- tion of Fire, Electrical Shock

Midi Channel, MIDI Controller, Amp Mute

Use this DIP switch to assign the MIDI channel by which the amp‘s MIDI system will receive program change commands and specific MIDI controller commands assigned to certain amp functions. Your choices are the standard 16 MIDI channels numbered from 00 to 15, as well as OMNI mode, whereby all MIDI data is received regardless of the MIDI send channel. MIDI-Channel S1 S2 S3 S4 S5 S6 OMNI OFF XX XX XX XX XX CH1 ON OFF

Functions SAVAGE II Amp:

MIDI Controller: as HEX value: Cntrl value 0-4 Cntrl value 5-127 Master A/B controller #14 0x0E off on Rough/Smooth controller #15 0x0F off on Input Lo/Hi controller #20 0x14 off on Preshape controller #21 0x15 off on Gain Lo/Hi controller #22 0x16 off on Bright controller #23 0x17 off on Noise Gate controller #24 0x18 off on Presence A/B controller #25 0x19 off on Depth Boost controller #26 0x1A off on Contour – Clean/Crunch I c

FX Loop I Send

Connect this FX Loop I output to a signal processor´s input/return or an effect pedals´s input/return jack using the shortest possible shielded cord equipped with 6.3 mm (¼“) plugs. Activate and deactivate it via the FX Loop I / II button, which switches between these two loops. In the signal path, FX Loop I is located post preamp and pre the two power amp Master knobs. FX Loop I Return Connect this FX Loop I input to a signal processor

Engl E610II FX Loop II Balance

FX mix control for FX Loop II. When the knob is set to Dry, the amp signal is routed through with no proces- sed signal (0% wet balance) added to the mix. Twist the knob clockwise to blend in the processed signal (parallel/passive, wet balance 1-99%, depending on knob position). When the knob arrives at the Effect position, only the wet signal (that is, the processed signal generated by the connected effect device) is patched to the powe

1. One 4 Ohm cabinet connected to a 4 Ohm jack

Summary: 4 Z, --> connected to 4 Ohm output 2. Two 8 Ohm cabinets connected to the 4 Ohm jacks Summary: 8 Z + 8 Z, --> connected to 4 Ohm + 4 Ohm output 3. One 8 Ohm cabinet connected to an 8 Ohm jack Summary: 8 Z, --> connected to 8 Ohm output 4. Two 16 Ohm cabinets connected to the 8 Ohm jacks Summary: 16 Z + 16 Z --> connected to 8-ohm + 8-ohm output. 5. One 16 Ohm cabinet connected to the 1

approx. 60 Watts; adjusted accordingly to 4, 8 and 16 Ohm – E630II

approx. 120 Watts; adjusted accordingly to 4, 8 and 16 Ohm – E610II Input sensitivity Input: from -20 dB, nominal, max. 0 dB Effect RETURN: from -20 dB, nominal, max. 0 dB Output level SEND, level range: from -20 dB to approx. 0 dB max. Line Out: approx. 0 dB at nominal power output Power consumption: approx. 280 Watt (335 VA) max. - E630II approx. 400 Watt

Engl Amplifier Owners Instructions: