Framery O VCR Installation Instructions Manual

2 Safety.................................................................................................................6 3 Installation requirements................................................................................ 8 3.1 Tools and accessories............................................................................... ...

11.1 Install the floor cover panels................................................................................... 57 12 Install the interior.........................................................................................58 12.1 Cut the carpet............................................................................................ ...

For the product warranty to be valid: This checklist must be filled and sent to Framery after pod installation. Take a photo/scan the filled list and send it to Framery at [email protected]. Leave the completed list on the pod's glass door. Country: _________________________________________ City: _________________________________________ Customer: _________________________________________ Pod serial number: ________________ ...

the pod. It is important that these instructions are followed to recognize and prevent potential risks before they occur. Note: All personnel must understand and observe these instructions prior to installation or maintenance of the pod. Restrictions • Non-conventional use • Installation or maintenance of the pod without reading and understanding the ...

• Ambient temperature: +15°C ... +30°C (59°F ... 86°F) • Humidity: max. 50% Framery O VCR Installation Instructions [email protected] 7 ...

3.1 Tools and accessories Figure 1: Tools and accessories needed for installation and maintenance Note: Use a white rubber mallet to not leave marks on the body covers. Note: Use a plastic chisel. 8 Framery O VCR Installation Instructions [email protected] ...

Note: Use a mild alcohol-based cleaning solution for cleaning the pod. 3.2 Display size Make sure that your display fits the display slot. Figure 2: Display slot dimensions 3.3 Installation space Make sure that you have enough installation space before you start the installation. Framery O VCR Installation Instructions [email protected] 9 ...

3.4 Operating space Make sure the pod has enough space for the air to circulate correctly. Figure 4: Operating space measures 10 Framery O VCR Installation Instructions [email protected] ...

1. Lay the floor module down at the intended final location. Leave approximately 0.5 m (2 ft) of empty space behind the floor module. Note: The stool mounting notch is closer to the backside of the pod. Framery O VCR Installation Instructions [email protected] 11 ...

The leveling screws are against the floor when you feel resistance. 3. Measure the floor module with a spirit level at four measuring points: • On top of the walls on the right and left sides • At the edge of the floor module (on the ABS strips) Measure opposite points repeatedly and adjust the feet of the leveling screws gradually. 12 Framery O VCR Installati ...

5.1 Remove the wall cover panels 1. Place the wall modules lengthwise against a wall. 2. Unscrew the 4x30 screws (8 pcs) and remove the cover panels (4 pcs). Set the cover panels and screws aside. Note: Make sure that the wall modules do not fall over. Framery O VCR Installation Instructions [email protected] 13 ...

panels and screws aside. 14 Framery O VCR Installation Instructions [email protected] ...

1. Lift the floor module up to stand on its side. Note: Do not move the floor module away from the intended location. Note: Check that the leveling screws are past the floor board level. Framery O VCR Installation Instructions [email protected] 15 ...

Note: Make sure that the flat side of the guide pin goes into the mounting hole. 3. Push the blank wall module carefully into place. Note: Make sure that the "This side up" sticker faces upwards and its arrows point to the inside of the pod. Note: Make sure that you install the blank wall module on the correct side of the floor module. The electrical channel is on the other sid ...

5. Push the techwall module carefully into place. Note: Make sure that the "This side up" sticker faces upwards and its arrows point to the inside of the pod. Note: Make sure that you install the techwall module on the correct side of the floor module. The power cord and the electrical channel are on the same side. Framery O VCR Installation Instructions [email protected] 17 ...

18 Framery O VCR Installation Instructions [email protected] ...

1. Install the guide pins (4 pcs) to the mounting holes. Note: Make sure that the flat side of the guide pin goes inside the mounting holes of the wall modules. Framery O VCR Installation Instructions [email protected] 19 ...

Note: Make sure that the roof module cord is in the electrical channel. Make sure that the wall module cord is not between the modules. 3. Install M8x35 bolts (3 pcs on each side) and M8 washers (3 pcs on each side). 20 Framery O VCR Installation Instructions [email protected] ...