CATSKILL 51533 Assembly Instructions Manual

Text of CATSKILL 51533 Assembly Instructions Manual

Mid-Sized Two Door Cart with Drop Leaf

GENERAL: 1. You have purchased model 51533. 2. Should you need assistance or need to replace a damaged or missing part simply give us a call M-F at 607-652-7321 from 7:30 am - 4:30 pm EST and we’ll send you the prepaid part via UPS usually that same day! You may also email us [email protected]. 3. Read the assembly instructions and the enclosed brochure before beginning ass

Plain Side Panel (1)

P/N:SP/PL-51533 Handle Side Panel (1) P/N:SP/HDL-51533 TOP TO T P OP Back Panel (1) P/N:BP-51533 Drawer Bottom (1) P/N:DBOT-51533 Left Door (1) P/N:DOR-51533/L Right Door (1) P/N:DOR-51533/R Drop Leaf (1) P/N:DL-51533 Table Top (1) P/N:TT-51533 Middle Shelf (1) P/N:MS-51533 Bottom Shelf (1) P/N:BS-51533 EDGE BANDING GOES OUT Drawer Front (1) P/N:DF-51533 Drawer Side Left (1) P/N:DS-51533/L Drawer Side Right (1

1 3/4” Phillips Flat Head Bolt (8)

1 1/2” Phillips Flat Head #8 Screw (4) Cam Posts (2) 1 1/4” Phillips Flat Head #8 Screw (8) 7/8” Truss Head Machine Screw (6) 5/8” Phillips Flat Head #8 Screw (23) 3/4” Long 3/16” DIA. Steel Pin (4) 1” Long 3/16” DIA. Steel Pin (8) 1 1/2” Long 3/16” DIA. Steel Pin (4) Hinge (2) Caster Socket (4) Cam (2) 5/8 Wooden Disk (8) Nickel Handle (3) Towel Bar Post (2) Non-Locking Wheel Caster (

5/8” #7 Screw

1 1/4” #8 Screw 5/8” #7 Screw STEP 1 A. Decide which side to put the towel bar on. Attach a Glide Support Stick to the top of each Side Panel using 1 1/4” #8 screws. The countersunk holes (reamed out) in the stick are positioned as in illustration 1 so that the glide holes are toward the lower edge. Sticks should be flush with top of panel. B. Attach the cabinet glide of the Drawer Glide to the Glide Support Stick using 5/8”

5/8” Phillips Flat Head #8 Screw

20 Used in this step Side Panel Leg Inside Brace Countersunk Hole in Leg ( disk goes in this hole to hide bolt head! ) Nut Access Hole Hex Nut STEP 2 A. Lay back panel flat on a smooth surface with holes up. B. Attach both side panels (glide wheels go toward front of cart) with 1 3/4” bolts and hex nuts. After inserting bolts through the holes in the side panels, through the holes in the long edges o

4 Used in this step

1” Long 3/16” DIA. Steel Pin PIN PIN 5/8” Phillips Head #7 Screw 4 Used in this step 3/16” Flat Washer 1” Phillips Flat Head #8 Screw 2 used in this step Bottom Front Brace 4 used in this step 3/4” Long 3/16” DIA. Steel Pin 3/4” Pin Top Front Brace Insert STEP 5 A. Turn the side/back assembly upside down (invert) on top of the inverted table top. B. Using the X marks as a guide, insert the tips of the 5/8 #7 screws into

1 1/4” #8 Bolts

Insert Brace Pins Here and slide down into correct position. Glide Suport Assembly ILLUSTRATION 8 2 used in this step Hex Nut 2 used in this step 1 3/4” Phillips Flat Head Bolt 1 1/2” Long 3/16” DIA. Steel Pin 4 used in this step 5/8” Phillips Flat Head #8 Screw 3 used in this step Magnet Plate 4 used in this step 1 used in this step RIGHT DOOR LEFT DOOR 1 1/2” Long 3/16” DIA. Steel Pin 4 used in this step 5/8” Phil

1 3/4” Phillips Flat Head Bolt

2 Used in this step 10-24 Hex Nut 2 Used in this step 2 Used in this step 3/16” Flat Washer 5/8” Pan Head Screw 2 Used in this step Magnet 5/8” Pan Head Screw 2 Used in this step STEP 10 Install Doors/Bottom Front Brace A. Install doors by inserting pins in the door tops into the holes in the top front brace. B. Place one washer on each of the door pins in the door bottoms. C. Take the bottom front brace, align pins i

Below line in wood

Cam Posts (2) 4 used in this step 1 1/2” Phillips Flat Head #8 Screw 2 used in this step 7/8” Truss Head Machine Screw 2 used in this step Cam 4 used in this step 5/8” Phillips Flat Head #5 Screw STEP 12 A. Attach the drawer back to the drawer side with four 1 1/4” #8 screws. Make sure parts are aligned as in Illustration 12A. B. Insert drawer bo

4 used in

this step 1” LONG 3/16” DIA. STEEL PIN STEP 13 Install Casters A. Insert and tap caster sockets with a hammer until the teeth grab the wood. DON’T POUND SOCKET FLAT OR CASTER SHAFT WILL NOT ENTER. B. Insert casters and seat by pushing straight downward with the heel of your hand, or tap into place with a hammer. Don’t be afraid to give them a good downward whack on the solid metal part of the caster! STEP 14 Install Shelves/D

CATSKILL Indoor Furnishing Owners Instructions: