Blitz FATT DC Quick Start Manual

is read and fully understood *Injury may be cause by improper installation. *Installation should be entrusted to a professional technician. *Double check all wire connections. Avoid all plastic or painted surface for ground wire. Bad ground may cause poor actuation of turbo timer and cause the breakdown of this product. Caution for installation work 1. Vehicles equipped with computer preset automatic steering. -Note that steering wheel does not tilt up even if the ignition key is pull out when the product is installed in vehicles equipped with computer preset automatic tilt steering. Features Auto Timer 2. Vehicles equipped with automatic light control. Manual Timer -Note that the light may be kept on even after the timer is off. When Temperature the turbo timer is actuated with the light switch is AUTOMATIC. Battery Voltage The light will remain on after the car shuts off. Stop Watch 5 Lap Times 3. Actuation of air conditioner. -Depending on the types of automobile, extremely large electric current may flow and cause breakdown of the turbo timer when the turbo timer and air conditioner is simultaneously actuated. Be sure Blitz Performance Sales Inc to turn off air condition when the turbo timer is actuated. 17300 Railroad St. #B City of Industry CA 91748 Tel 626 839-8350 Fax 626 839-8340 www.Blitz-Performance.com Page 1 Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes

1. Remove lower instrument panel as shown in figure 1 #B. genuine Blitz turbo timer harness (sold separately) into the starter 2. Remove upper and lower steering column cover as shown in figure 1 #A. coupler. 3. Locate the key ignition coupler. 5. Connect the Blitz turbo timer harness to the 3 pin connector as shown below. 6. Connect 3 pin harness to 4 pin harness. 7. Ground all black wires as shown in figure 2. Ground should be metallic portions and avoid painted surfaces. 8. The purple wire should be grounded or hooked up to the hand break. *Illustration shown above is reverse. Page 2 Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes

-Check if all wires are connected securely. Insufficient wiring may cause poor actuation of the product. In the worst case, it may *Important-the parking brake wire (purple) must have ground result in the breakdown of the engine. signal at all times, either by grounding the wire or -Be sure wiring are neatly installed without any interference with reading ground signal from the parking brake wire. surrounding parts. Short circuit may occur due poor connections. If purple wire is not install correctly, the turbo timer In the worst case, it may result in breakdown or the engine. will automatically shut off when key is taken out. CAUTION: When confirming actuation of turbo timer, be sure that the gear is in neutral or parking position and the foot 1. Parking brake. Purple wire is on the brake. Also be sure there is no one around the A. Single wire parking brake. vehicle. connect purple wire as shown in figure A. In case of Failure of product B. More than one wire. Check the following before concluding there is any failure of this a. Turn key to ON position. product. (do not start engine) 1. Check if wires is connected securely and connectors is inserted b. Use test light to find the rigidly. wire with 12V power 2. Check if ground wire is ground correctly. when the parking brake 3. Check if tap is securely connected. is down. Connect to that wire as shown in figure B. CAUTION: Parking brake can be bypass if purple wire is grounded. *Engine will shut off if the parking brake is release at anytime during count down. Page 3 Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes

The idling time is automatically set by the timer. Idling time varies on what mode the auto timer is set on and the variations of the vehicles ignition pulse. -Mode display is located on the left side of LCD 1. Automatic Timer A 1 2 3 When the FATT DC is turned on the Automatic Timer mode will be activated. The "TIMER A" will be displayed 1 - Power Button 2 - Minute Button ( Start / Stop for stop watch function ) To set the minimum time of the auto timer press the 3 - Second Button ( Lap button for stop watch function ) MINUTE button once and the screen will flash. Then press SECOND button to set the base time between Settings 0 to 50 seconds. ** When the A appears, the Automatic Timer function is activated. When the Timer is activated the modes will appear as follows: Press the MINUTE button on the Temperature or Battery Voltage display to turn the Automatic Timer on or off. Make sure that the letter A appears 1 - Automatic Timer The A means auto timer is activated 2 - Manual Timer There are 4 different auto timer modes. Press the MINUTE button twice when 3 - Temperature in Automatic Timer Mode. The automatic timer modes will go as follows A - H A - S E -L E - H A - L Press the SECOND button to switch between the modes. 4 - Battery Voltage 5 - Stop Watch A - L mode will start to calculate time to automatic function mode after 1800 rpm. Low setting 6 - Lap Time Display A - H mode will start to calculate time to automatic function mode after 1200 rpm. Medium setting A - S mode will start to calculate time to automatic 7 - Off function mode after 900 rpm. High setting E - L mode will add time according to how long the Press the POWER to button to switch to the next mode. ignition has been on roughly 55 seconds per hour E - H mode will add time according to how long the ignition has been on roughly 130 seconds per hour Page 4 Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes

4 - Battery Voltage Press the POWER button twice to get to the When the unit is first turned on press the POWER button four times to display manual timer mode. The screen will display the Battery Voltage mode. This will display the vehicles Battery voltage. "TIMER" The will not be an A visible. When on Temperature display press the MINUTE To set the time of the manual timer press the MINUTE button to set the number button to activate the Automatic Timer function of minutes you want the car to idle after the vehicle has been shut off. Press the letter A will appear. the SECOND button set the number of seconds desired. You can choose idling times between 0 to 10 minutes When on Temperature display press the MINUTE button to activate the Manual Timer function ** To activate the manual timer go to the BATTERY or TEMPERATURE display the letter A will disappear. and press the MINUTE button. Make sure that the letter A does not appear. 3 - Temperature 5 - Stop Watch When the unit is first turned on press the POWER button three times to display When the unit is first turned on press the POWER button five times to display the Temperature mode. The temperature sensor is in the control module. the Stop Watch mode. This can be used to record the time it takes to get to The Temperature is displayed in Celsius ONLY. point A to point B. The Stop Watch will record times up to 9 minutes **The temperature is accurate depending on where the control module is placed. and 59 seconds. When on Temperature display press the MINUTE Use the MINUTE button for the Start and Stop Function keys. Use the button to activate the Automatic Timer function SECOND button for the lap button. the letter A will appear. When on Temperature display press the MINUTE button to activate the Manual Timer function the letter A will disappear. To start and stop the Stop Watch press the MINUTE button. Press the Second button to jump to another Lap. There is 5 Laps available. If the laps are full the LCD will display full when trying to record another Lap. To clear the time press the SECOND button and hold it down for 5 seconds. Page 5 Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes

LCD DISPLAY When the unit is first turned on press the POWER button six times to display CONTRAST the Lap mode. The Lap mode can display up to 5 recorded times. When the FATT DC is turned off the user can adjust the contrast by Press the SECOND button once to scroll through pressing the MINUTE and SECOND button. The user can adjust the and view the recorded lap times. Press the second illumination between 0 to 100. button and hold it down for 5seconds to CLEAR all the recorded times. BAR DISPLAY 7 - Off When the Turbo Timer is on Auto Timer E Mode the user can have different bar displays. In order to do this select E - H or E - L mode in the Auto Timer setting. When the unit is first turned on press the POWER button seven times to display When the E mode is activated the Bar Display will move side to side. the Off mode. The leave the display on off mode and the FATT DC will turn off automatically. To change the Bar Display press the SECOND button down for 3 seconds and the display will change. There will be 4 possible displays. 3 of the displays will be automatically moving and the fourth display will move according to the vehicle ignition pulse. ** This automatic back and fourth function only works on the E mode of the Auto Timer setting Press the POWER button to turn on the turbo timer. A and B switch There is a switch on the control module. A is for most vehilcle applications. The B switch is for vehicles with low ignition pulses. Page 6 Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes Online Manual Not For Resale Purposes