Black & Decker BDBS100 Instruction Manual

POUR LE FRANÇAIS, VOIR LA COUVERTURE ARRIÈRE. SAVE THIS MANUAL FOR FUTURE REFERENCE. INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. INSTRUCTION MANUAL 99 IINNCCHH ((222299M MM M)) BBEENNCCHH BBAANNDD SSAAW W Cat.No. BDBS100 For ...

MANUAL BEFORE OPERATING THE MACHINE. Learning the machine’s application, limitations, and specific hazards will greatly minimize the possibility of accidents and injury. 2. USE CERTIFIED SAFETY EQUIPMENT. Eye protection equipment should comply with ANSI Z87.1 standards, hearing equipment should comply with ANSI ...

extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. See the Extension Cord Chart for the correct size depending on the ...

CURRENT CARRYING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES GROUNDED OUTLET BOX GROUNDING MEANS ADAPTER 2. Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating less than 150 volts: If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fi ...

extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord w ...

2 - Lamp 3 - Lamp Cord Clamps(2) 4 - 1/4in. Lockwashers (2) 5 - M6x1x12mm Cap Head Screws (2) Fig. 2 6 - Table 7 - M6x1 Wing Nut 8 - M6 Flat Washer 9 - M6x1x30mm Pan Head Screw 10 - 4mm Hex Wrench 11 - 3mm Hex Wrench 12 - Pointer 13 - M5x.8x10mm Pan Head Screw 14 - M10 Flat Washer 15 - Lever Assembly 16 - Pinion Knob 17 - Spring 18 - Special S ...

Fig. 4, M10 flat washer (B) and 4mm wrench (C). 2. Using the 4mm wrench (C) Fig. 4, supplied, remove screw (D) and spring (E) from handle (A) and remove handle from nut (G). Do not lose spring (E). 3. Place table (H) Fig. 5, onto the band saw frame so that stud (J) Fig. 6, and k ...

special screw (P). 7. Position pinion knob (N) Fig. 10, onto the back of saw so that the teeth on the pinion knob (N) engage the teeth on the trunnion (R). Fasten in place with special screw (P) and spring using the supplied 4mm wrench. 8. Fasten pointer (S) Fig. 11, to the back of ba ...

cover of the machine, using two M6x1x12mm cap head screws (B) and 1/4 in. lockwashers as shown. 2. Peel backing from cord clamps (C) Fig. 13A, and apply one clamp at each of the locations shown. Make certain the lamp cord is routed out of the way of the blade, then secure cord (D) to cord clamps (C) as sho ...

Fig. 15 Fig. 16 Fig. 17 WARNING: THIS PRODUCT IS RECOMMENDED FOR WOOD CUTTING ONLY. STARTING AND STOPPING SAW The switch (A) Fig. 15, is located on the front side of the band saw. To turn the saw “ON” move the switch (A) up to the “ON” position. To turn the saw “OFF” move the switch (A) down to the “OFF” ...