Doran 2200CW Technical Manual

Technical Manual MAN347 – Rev E Doran Scales, Inc. www.doranscales.com ...

Scale Setup ............................................................................................................................ 1 Unpacking Your Scale .....................................................................................................................1 Specifications ........................................................................................................................ 2 Scale Controls and Operat ...

Setting Time and Date .................................................................................................................. 13 Accumulator and Counter .................................................................................................... 14 Accumulator and Counter Operation ....................... ...

Wired Ethernet Option ........................................................................................................ 51 Wireless 802.11b/g Ethernet Option .................................................................................... 52 Bluetooth Option .................................................................. ...

obtaining all the benefits that the indicator can provide. If any questions arise, please contact the Doran Scales Technical Support Department at 630-879-1288. Unpacking Your Scale Before unpacking your Doran scale, please read the instructions in this section. Your new scale is a durable industrial product, but it is also a sensitive weighing instrument. No ...

CWM Certificate Class III – 10,000d; Cert. #AM-5617 Enclosure 304 Stainless Steel Product Dimensions 10” W x 6.75” H x 3.5” D Environmental Protection IP69K Legal for Trade Temperature Range 14 F to 104F (-10 C to +40 C) Resolution Range 200d to 100,000d Analog Signal Sensitivity 0.16 V/e minimum, 0.5 V/e typical System Linearity 0.01% full scale Analog Signal Range -0.5mV ...

Fig. 1: Front Panel Scale Annunciators Unit of measure lb, oz, kg, g or lb:oz. The units annunciator to the right of the display will indicate the current unit of measure. Net weighing mode is indicated by the NET annunciator. The annunciator will illuminate when a net weight is displayed. When not illuminated, a gross weight is displayed. Battery option status indicator. When the annunciator illuminates, the battery charg ...

weight. The annunciator will illuminate when motion is sensed on the platform. Changes in weight, vibration or air currents can cause the scale to go into motion. Under illuminates to indicate weight is below the Under target and above the Low target or flashes if below the Low target. Accept illuminates to indicate weight is at or above the Under target and at or below the Over tar ...

display a net weight and the NET annunciator will illuminate. Tare weights will remain in memory even if the indicator is turned off. Keyboard TARE entry Enter a weight and press TARE to save or press CLEAR to cancel tare entry. The scale will display a net weight and the NET annunciator will illuminate. Display TARE value To display the current tare value, press ...

To activate password protection, the PASS parameter must be configured with a numeric password. Once configured, password protection will be activated upon power up. If password protection is activated, the display will show PASS when SETPOINT, TARE, UNDER, or OVER values are displayed. Password protection also inhibits deletion or creation of new product IDs. Enter the password and press ENTER, the display will then show PAS ...

Lead-Acid battery and charging circuit, both internal. The scale is designed to run continuously for up to 60 hours with a single 350 ohm load cell. To maximize battery life, leave the auto-off timer enabled which will automatically power down the scale after a period of non-use. Power Off 1) Manual - Press and hold the ZERO push button until the displ ...

Three band checkweighing classifies weighments into over, accept and under. The default configuration is three band checkweighing. Note that lb:oz is not supported for checkweighing limits. Three Band Checkweighing (C.o. set to operation starting with 3) 1. Remove all items from the scale platform 2. Press ZERO and the display will read zero weight 3. Place an item on the scale platform and wait for the scale to stabilize 4. Acce ...

Five band checkweighing classifies weighments into high, over, accept, under and low. Note that lb:oz is not supported for checkweighing limits. Five Band Checkweighing (C.o. set to operation starting with S) 1. Press ZERO 2. Place an item on the scale 3. Checkweigh status is indicated as follows a. Flashing OVER = HIGH b. Solid OVER = OVER c. Solid ACCEPT = ACCEPT d. Solid UNDER = UNDER e. Flashing UNDER = LOW Enter and Display o ...

1. Press ZERO 2. Place an item of the desired weight on the scale platform 3. Press and hold the OVER or UNDER until the display reads High or louu respectively 4. The display will briefly read over or underfollowed by the weight on the platform and checkweigh status annunciators will flash 5. Press either OVER to increase the weight value or press UNDER to decrease the weight value. Pressi ...

be easy to manage with Doran’s data management programs. Product IDs save information that includes:  Checkweigh limits  Unit of measure  Accumulator and counter values  Tare  Two 40 alphanumeric character fields  Number of samples and alarm timer for QC Weigh  Motion Aperture (nn.A.)  Threshold (tHs)  Checkweigh operation ( ...

values for each field. When changing products, the display will read SaVed to indicate the all fields associated with the new Product ID number are saved and will be recalled when that product is used again. Delete PRODUCT ID from Memory Enter the product ID to be deleted and press PROD ID. The display will show pRd Id, followed by the product ID number. Press and hol ...

Setting Time and Date To change the date: 1. Press and hold decimal point / clock button until date is displayed 2. The display flashes the current the date 3. The digits being edited flashes on the display 4. Enter the date with leading zeros in the format MM.DD.YY 5. Press UNITS to advance to the next digit 6. Press UNITS until the display reads saved to confirm the date changes are saved 7. Press ENTER to return to the normal weighing m ...

Accumulator and Counter Operation When a manual or automatic print function is executed, the accumulator has the currently displayed weight added to its’ current value and the counter is incremented. To accumulate automatically, select an auto print function in the parameter setup menu. To accumulate manually, allow the scale to become stable and press PRINT. The maximum value that can be shown for the accumulator and counter i ...

Removing and Replacing the Rear Panel Before you remove the rear panel, remove AC power. Power down the scale if the optional battery power is present. Removing the rear panel requires a 5/16” nut driver. To replace the rear panel and achieve a tight seal, each screw requires a rubber bonded washer and the gasket needs to be in place. Tighten screws to 20 in-lb to achieve proper sealing. Tighten all wat ...