Black Box HS300A Operation & User’s Manual

AND INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication. It has been tested and found to comply with the limits for a Class A computing device in accordance with the specificat ...

FCC REQUIREMENTS FOR TELEPHONE-LINE EQUIPMENT 1. The Federal Communications Commission (FCC) has established rules which permit this device to be directly connected to the telephone network with standardized jacks. This equipment should not be used on party lines or coin lines. 2. If this device is malfunctioning, it may also be causing harm to the telephone network; this device should be disconnected until th ...

to determine how many devices can be connected to your telephone line. In most areas, the sum of the RENs of all devices on any one line should not exceed five (5.0). If too many devices are attached, they may not ring properly. 6. In the event of an equipment malfunction, all repairs should be performed by your supplier or an authorized ag ...

CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. The LOAD NUMBER (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of ...

fabricante. 8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser referido a personal de servicio calificado. 9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su uso. La colocación del aparato ...

17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilación. 18. Servicio por personal calificado deberá ser provisto cuando: A: El cable de poder o el contacto ha sido dañado; u B: Objectos han caído o líquido ha sido derramado dentro del aparato; o C: El aparato ha sido expuesto a la lluvia; o D: El aparato parece no operar normalmente ...

TRADEMARKS USED IN THIS MANUAL AT&T® and Merlin® are registered trademarks of American Telephone and Telegraph Company. Siemens® is a registered trademark of Siemens Aktiengesellschaft. Toshiba® is a registered trademark of Toshiba Corporation. UL® is a registered trademark of Underwriters Laboratories Incorporated. Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owner ...

Contents 1. Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

1. Specifications Baseband Modulation— ADPCM Battery Life—12 hours of continuous use, on-line; 80 hours of continuous use, off-line Battery Recharge Time— 3 hours Channels—120 Channel Selection— Automatic Compatibility—All business phones that comply with RF immunity spec: CISPR24: 1997, modified; Carbon, Electric, AT&T®: Switch selectable; Siemens® Dyad: Accessory hookup cord Compliance—UL® 1459, CSA, FCC Parts ...

2. Introduction 2.1 Description The 2.4 GHz Wireless Amplifier and the Remote Unit use Spread Spectrum technology to give you wireless access to your phone. With the wireless system, you’re free to find a file, confer with a colleauge, check with shipping, or roam the building—without putting your caller on hold. NOTE The 2.4 GHz Wireless Head- set system includes the base unit, remote unit, Hookswitch, a ...

1 2 3 4 5 6 7 8 A B C D E F G D. Base Stand A. B. C. D. I. II. III. IV. V. E. F. G. VI. VII. ...

2.4 GHZ WIRELESS REMOTE UNIT WITH HOOKSWITCH 3. Installation 3.1 Assembling the Base and Connecting to the Telephone 1. Disconnect the handset cord from the telephone and connect it to the port marked with the 0 icon at the bottom of the base. Connect one end of the telephone interface cord to the telephone handset port and the other end to the bottom of the base marked with the 1 icon. Connect the AC power a ...

Figure 3-3. Aligning the Tab. 4. Connect the headset to the bottom of the remote. Insert the remote into the base (see Figure 3-4). Either side may be used. The battery charge indicator marked with the 5 icon on the base will light up. This will be referred to as the front of the base. Fully charge the remote for 3 hours before using. Figure 3-4. Connecting the Headset. 3.2 Checking the System Put the system in headset mode by p ...

2.4 GHZ WIRELESS REMOTE UNIT WITH HOOKSWITCH 3.4 Before Setting Up to the Telephone 1. Make sure the headset/handset selector marked with the 30 icon on top of the base is in the headset position. The selector is in the headset position when the on-line indicator (marked with the 4 icon) on the front of the base lights up and the on- line indicator on the top of the remote is flashing. If the lights are off, ...

Figure 3-7. Adjusting the Telephone Compatibility Switch. 3.5.2 STEP 2: ADJUSTING THE TRANSMIT (MICROPHONE) SOUND LEVEL Change from the headset to the handset position by pressing the headset/handset selector (marked on top of the base with the 30 icon) once. Call someone using your handset, then switch over to your headset. Ask for help evaluating the sound level of your voice so that the level is the same as when you used the ...

2.4 GHZ WIRELESS REMOTE UNIT WITH HOOKSWITCH Table 3-1. Telephone Compatibility Guide Manufacturer System Phone Set Setting AT&T (Lucent) Definity 7100, 7300, 7400 Series A Merlin® BTN, BIS, & 7000 Series A ISDN 6500, 7500 Series A 1A2 2500 Series G Merlin Legend MLX Series A Consumer Products Traditional & Feature A Comdial Executech, Impact All Sets A Mitel SX Series All Supersets A NEC Electra D-Term Seri ...

4. Operation 4.1 Using with a Headset 1. Make sure the headset/handset selector on top of the base is in the headset position. Put on the headset, pick up the handset, and answer the phone or make a call. 2. To end the call, put the handset down. 3. When you answer or make a call using the headset, the on-line indicator on the base starts flashing. This means the base is communicating with the remote (Figure 4-1). Figure 4-1. On-Lin ...

2.4 GHZ WIRELESS REMOTE UNIT WITH HOOKSWITCH Figure 4-2. Removing the Pocket Clip. 3. Slide the belt clip onto the back of the remote until it clicks into place (Figure 4-3). Figure 4-3. Sliding the Belt Clip into Place. 4.4 Adjusting the Volume To turn the sound level up or down in your headset, press successively on the volume control button marked with the 7 icon on the front of the remote (Figure 4-4). If ...

the mute function is on, you can still hear the other party. Figure 4-5. Muting the Microphone. 4.6 Recharging the Battery To ensure optimum battery life, place the remote in the base when not in use. The recharging indicator on the base, marked with the 5 icon, automatically lights up while the battery is in the base. It takes 3 hours to fully recharge the battery. A fully charged battery provides 12 hours of continuous talktime. I ...