Delta OHM HD40.1 Manual 

differences between information written in this manual and the instrument that you have pur- chased. We cannot entirely exclude errors in the manual, for which we apologize. Data, figures and descriptions contained in this manual cannot be legally asserted. We reserve the right to make changes and corrections without prior notice. REV. 1.0 23th Jan. 2008 Po ...

1. STATUS Led: shows the printer status. 2. MENU key: advances paper by two lines. When you turn on the printer, if you press the Menu key and the ON/OFF key, you activate the printer configuration mode. 3. Cover that gives you access to the paper roll and the printing mechanism. 4. POWER Led: provides information on rechargeable battery status. 5. ON/OFF Key: switches on and off the printer. If you press it with the MENU key, ...

HD40.1 is connected to instruments or PC through the RS232 serial input. The HD40.2 features a dual mode data reception system - RS232 serial and Bluetooth. The Bluetooth wireless connection makes the HD40.2 printer very useful “in the field”, since it does not require any connection to the instrument. A careful design allows you to replace the th ...

ON/OFF Key Press the ON/OFF key until the Status led starts blinking to turn on the printer, then release the key. Press the ON/OFF key until the Status led remains on to turn off the printer, then re- lease the key. To access the configuration mode, press the ON/OFF key and the MENU key to turn on the printer: when the paper roll starts advancing, release both keys (see chapter 3.4, Setup description). MENU key W ...

remains on: now you can release the key. The printer turns off. The following table shows different POWER and STATUS led combinations. STATUS LED Description Always off. Printer is off. Blinks slowly (every two seconds). Printer is on and ready to print. Remains on. Printer is turning off. When the printer is on, you are pressing the ON/OFF key to turn it off. ...

3.1. ConnECTIONS The printer has one input (1) for the battery charger power supply and one plug (2) for RS232 serial connection. Power supply connector The power supply connector is 5.5mm in outer diameter and 2.1mm in inner diame- ter. The positive pole is in the middle The printer is provided with the SWD10 power supply which features: • Output voltage: 12Vdc • Maximum current: 1A. The printer is sup ...

HD2110CSNM cable for instruments with 8-pole Mini DIN connector (ex. HD21xx and HD34xx.2 series, HD2010, HD2110, etc.). Use the 9CPRS232 cable for instruments with 9-pole connector (ex. HD22xx.2 se- ries, HD25.2, etc.). 3.2. HOW TO LOAD PAPER The printer uses thermal paper rolls which are 57mm wide and max. 32mm in diame- ter. Loading thermal paper roll is easy an ...

4) Tear off excess paper. The printer is ready. ...

Use the SWD10 battery charger supplied with the printer to charge batteries. Follow the steps below: • Connect the battery charger plug to the mains and the battery charger connector to the socket in the rear of the printer. • If batteries are extremely discharged or temperature is too low, the POWER led blinks for a few seconds (precharge) and then it remains on to indicate printer quick charge ...

Follow the steps below to replace the battery pack: • Disconnect the external power supply and turn off the printer. • Unscrew (2) the battery compartment cover located at the bottom of the printer (1). • Remove the connector. Make sure you don’t tear wires. • Remove the battery pack. • Plug the connector to your new battery pack: a notch on the connector will help you insert it correctly. • Pos ...

The printer operating parameters are as follows (factory values have been under- lined): 1. Interface selection: only RS232 for the HD40.1, RS232 or Bluetooth for the HD40.2. 2. RS232 serial communication baud rate: 9600, 19200 or 38400. 3. Automatic switch-off delay: 0, 5, 10 or 15 minutes. 4. Printing density: -2, -1, 0, +1, +2. Please follow the steps below to change these parameters: • When the printer i ...

When this interval of time has elapsed, the printer turns off automatically if you have neither entered any command nor pressed any key. You can set the following intervals: 0 or 5, 10 or 15 minutes. If you choose 0, the automatic switch off is disabled and the printer turns off only if you press the ON/OFF key. 4) Printing density This parameter allows changing the intensity of print character. “0” is the stan ...

The printer has an RS232 serial interface with a 9-pole RS232 connector located in the rear of the printer. Two different connection cables are available on request ac- cording to the device you want to connect - instrument or PC -: • Cod. 9CPRS232: is a 9 pole – 9 pole cable for any instrument with standard se- rial connector and for PC connection. It is also suitable for other brand instru- ments ...

9CPRS232 Cable HD2110CSNM Cable DB9 to instrument or PC DB9 to printer MiniDIN to instrument DB9 to printer 1 4 1 9 2 3 2 1, 6 3 2 3 4 4 1 4 8 5 5 5 2 6 Disconnected 6 3 7 8 7 5 8 7 8 7 9 9 4.2. BLUETOOTH INTERFACE The HD40.2 model has a Bluetooth interface. The printer communicates with Delta Ohm instruments fitted with the HD22BT Blue- tooth module. Besides, it receives print commands from a PC wi ...

Instrument storage conditions: • Temperature: -25...+70°C. • Humidity: 10...90%RH without condensation. • Make sure you avoid: High humidity. Exposure to direct solar radiation. Exposure to a high temperature source. Strong vibrations. Steam, salt and/or corrosive gas. The instrument enclosure is made of ABS plastic: use only compatible solvents for cleaning. ...

Please find below a step-by-step guide to using, initially setting and connecting your printer to an instrument, as well as printing via RS232 or Bluetooth. The guide refers to the two most popular connection methods: you can set other methods by following the instructions in the chapters of this guide. 6.1. CONNECTION VIA RS232 CABLE For the HD40.1 and HD40.2 printers. Follow A, B, C, D steps in this order. A) Befo ...

In the instrument you must set: • baud rate at 38400 • Printing interval. • Interface on PRINTER (For a few instruments only , ex. sound level meters). Important note: the printer baud rate and that of the instrument must be the same, otherwise the printer doesn’t work. For further details, please look at the instrument manual. D) How to connect the instrument to the printer Connect the printer to the ...

• This parameter does not affect the Bluetooth interface. Press the ON/OFF key to confirm the value printed. • The roll paper advances and the Automatic switch-off delay parameter will appear. • Press the MENU key to select the required value (the factory parameter is 5 min- utes, 0 disables automatic switch-off). Press the ON/OFF key to confirm. • The roll paper advan ...