FAAC AIRSLIDE Installation Manual

FAAC S.p.A. Soc. Unipersonale Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY Tel. +39 051 61724 - Fax +39 051 758518 www.faac.it - www.faacgroup.com Translation of the original instructions ENGLISH © Copyright FAAC SpA since 2017. All rights reserved. No part of this manual may be reproduced, archived, distributed to third parties nor copied in any other way, in any format and with any means, be it electronic, mechanical or by photocopying, without prior written authorisation by FAAC SpA All names and trademarks mentioned are the property of their re- spective manufacturers. Customers may make copies exclusively for th ...

Translation of the original instructions ENGLISH EU DECLARATION OF CONFORMITY The Manufacturer Company name: FAAC S.p.A. Soc. Unipersonale Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY hereby declares on his own responsibility that the following products: Description: Air curtain for automatic entry Model: AIRSLIDE KIT ; AIRSLIDE PA comply with the following applicable EU legislations: EMC Directive 2014/30/EU Directive ROHS 2 2011/65/EU LVD Directive 2014/35/EU Furthermore, the following harmonised standards have been applied: EN 61000-6-2:2005 EN 61000-6-3:2007+A1:2011 EN60335-2-80 : 2003 + A1 : 2004 + A2 : 2 ...

Translation of the original instructions ENGLISH EC DECLARATION OF CONFORMITY OF A MACHINE (2006/42/EC ANNEX II P.1, A) Manufacturer and person authorised to compile the technical file Company name: FAAC S.p.A. Soc. Unipersonale Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY hereby declares on his own responsibility that the following products: Description: Automatic entry with integrated air curtain Model: AIRSLIDE CS complies with the following applicable EU legislations: Machinery Directive 2006/42/EC (including all applicable amendments) and that the technical file has been compiled in compliance with part A ...

Translation of the original instructions ENGLISH CONTENTS EU Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 EU Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 EC Declaration of conformity of a machine . . . . . . . . . . . . . . . . . . . 4 1. INTRODUCTION TO THE MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.1 Safety recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Safety of the installer/maintenance technician . . . . . . . . . . . . . . 6 Workplace safe ...

Translation of the original instructions ENGLISH 1. INTRODUCTION TO THE MANUAL The instructions manual provides the correct procedures and re- quirements to be complied with for installation and operation of the system in safe conditions. ! Carefully read and comply with all the instructions before starting any activity on the product. Keep these instructions for future reference.   Unless otherwise specified, the measurements provided in the instructions are in mm. In writing the instructions manual, due account was taken of the results of the risk assessment conducted by the manufacturer on the entire life cycle of the ...

Translation of the original instructions ENGLISH 1.2 MEANING OF THE SYMBOLS USED ! Perform the operations and steps described in compliance with safety regulations and the instructions provided so as to prevent the risks indicated by the symbols in the following tables.  2 Symbols: tools (type and size) 6-8... HEX WRENCH of the specified size (6, 8...) 6-8... ALLEN KEY with ROUND HEAD of the specified size (6, 8...) TORX WRENCH of the specified size (6, 8...) 6-8... CROSS-HEAD SCREWDRIVER of the specified size (6, 8...) 6-8... METAL DRILL BITS of the specified size (6, 8...) 6-8... MASONRY DRILL BITS of the specified size ( ...

Translation of the original instructions ENGLISH  3 Symbols: safety signs and symbols (EN ISO 7010) GENERIC HAZARD It indicates the risk of personal injury or damage to parts. ELECTROCUTION HAZARD It indicates the risk of electrocution due to the presence of live parts. RISK OF CRUSHING AND MUSCULO-SKELETAL DISORDERS It indicates the risk of crushing and musculo-skeletal disorders due to lifting heavy parts. BURNING OR SCALDING HAZARD It indicates the risk of burning or scalding due to the presence of parts at high temperature. CRUSHING HAZARD It indicates the risk of crushing hands/feet due to the presence of heavy parts. ...

        Translation of the original instructions ENGLISH 2. AUTOMATION AIRSLIDE 2.1 INTENDED USE The AIRSLIDE systems with integrated air blade at the entry ensure a greater level of insulation between the indoor and outdoor environ- ment, protecting the entrance area from winter cold and summer heat without dispersion, also protecting the rooms from dust, pollution and insects from the outside area. . The AIRSLIDE series automations are designed to automate entry doors that are used exclusively for pedestrian traffic. They are compliant with standard EN 16005:2012. They are suitable for installation indoors, for appl ...

Translation of the original instructions ENGLISH 2.3 TECHNICAL SPECIFICATIONS AIRSLIDE  7 Technical specifications MODEL AIRSLIDE MAX installation height (m) 2.5 MAX recommended opening width (m) 2.2 Power supply voltage 220-240V~ 50-60Hz MAX absorbed power [W] 160 (single motor) - 330 (double motor) Electric motor Asynchronous single phase motor Motor rotation speed (rpm) 2850 Beam dimension (D x H) (mm) 182.1 x 252.5 (Including Grille) Fan diameter (mm) 80 Fan length (mm) 360 - 500 Speed of air output from the grilles from 0 to 2.5m in height (m/s) 15.3 - 4.2 Air flow rate (m3/h) 1250 Noise level (dB) at 5m 49.5 - 57. ...

Translation of the original instructions ENGLISH AIRSLIDE COMPONENTS Support profile Main profile AIRSLIDE for assembly of components and plate. Side fixing plates (Optional) Support profile side fixing plates FRONT CASING CLOSING PROFILE Aluminium profile for front head section closure. Plates with screws plates with screws for installation of components. Master electric fan unit and E1AS board plate Master electric fan unit and E1AS board plate. Additional fan module Additional electric fan module to be connected to the Mas- ter electric fan module Slave electric fan unit Slave electric fan m ...

Translation of the original instructions ENGLISH 2.4 TYPES OF SYSTEM SUPPLIED The AIRSLIDE series systems may be supplied as follows: - Air curtain in kit form for automatic entry: AIRSLIDE KIT - Assembled air curtain for automatic entry: AIRSLIDE PA - Automatic entry with integrated air curtain : AIRSLIDE CS INSTALLATION ACCORDING TO THE TYPE OF SYSTEM SUPPLIED ! During installation, it is recommended to comply with the order of the sections set out based on the type of purchased supply. AIRSLIDE KIT B A A. Pack containing AIRSLIDE components to be assembled on the FAAC support profile. B. Pack with FAAC profiles purchas ...

Translation of the original instructions ENGLISH 3. INSPECTION AND PREPARATION 3.2 ARRANGEMENT OF ELECTRICAL CABLES ! Before performing any operation on the system, disconnect the power supply. The electrical system must be compliant with the regulations in force in the Country of installation (EN60335-2-80 : 2003 + A1 : 2004 + A2 : 2009) The power mains of the automation must be fitted with a multi-pole power switch with a switch-contact gap of at least 3 mm. It is ad- visable to use a 6A circuit breaker with a multi-pole power switch. Ensure there is a residual current device with a 0.03 A threshold upstream of the system. ...

Translation of the original instructions ENGLISH 4. TRANSPORT AND RECEIPT OF THE GOODS 4.1 HANDLE PACKAGES ! Always comply with instructions on the package.   The NET WEIGHT is indicated on the package. PALLETISED SUPPLY RISKS PERSONAL PROTECTIVE EQUIPMENT REQUIRED TOOLS SINGLE PACKAGE RISKS PERSONAL PROTECTIVE EQUIPMENT REQUIRED TOOLS For manual lifting, there should be 1 person for every 20 kg to be lifted. 4.2 UNPACK AND HANDLE RISKS PERSONAL PROTECTIVE EQUIPMENT REQUIRED TOOLS For manual lifting, arrange for an adequate number of people for the weight of the leaf: 1 person for every 20 kg to be lifted. 1. Open and ...

Translation of the original instructions ENGLISH 5. CUTTING THE PROFILES   If the AIRSLIDE KIT has been supplied, the profiles must be cut to the size indicated. This operation is performed in the shop. After cutting, assemble the components to the support profile. Handling instructions:  14. RISKS PERSONAL PROTECTIVE EQUIPMENT REQUIRED TOOLS Use a circular or linear saw cutting machine with blade suitable for cutting metals. It is forbidden to use a hand saw. Only use equipment in good conditions and fitted with all the required safety devices. Always comply with the instructions provided by the equipment's manufact ...

1        Translation of the original instructions ENGLISH 6. ASSEMBLING THE HEAD SECTION   If the AIRSLIDE KIT has been supplied, the components must be installed on the support profile. This operation is performed in the shop. The assembled head section is then moved to the installation site. Handling instructions  14. RISKS PERSONAL PROTECTIVE EQUIPMENT REQUIRED TOOLS Ø 18 mm 6-8-10-13 5-6 45°... ! A torque wrench must be used to achieve the specified fastening torques (Nm). For manual lifting, arrange for an adequate number of people for the weight of the leaf: 1 person for every 20 kg to be lifted. 6 ...

2 2 1 A B C D E F G A B C D E F G 2 22 16 Nm 6-8... 2 ,5 Nm 1 Translation of the original instructions ENGLISH Make a hole in the main profile for fitting the lock 2.   If holes are drilled in the head section to allow passage of the power cables, fit a cable guard to protect it from any sharp borders and burs. ...

4            1 6 6 Nm     1 6 6 Nm    3 Translation of the original instructions ENGLISH The unit is fixed to profile AIRSLIDE using fastener plates with M6 screws inserted in the profile. Fasten the electronic module plate using three fastener plates and M6 screws and fasten each fan module using two fastener plates and M6 screws on each side 3-. Insert the protective cable sheath at the sides of the modules 1- ! Do not install devices which could cause condensation or other liquid above the electronics module plate in order to prevent liquid dripping onto the E1AS electronic board case. In th ...

5  3 2,5 2,2 Nm 4 4 3,3 Nm   Translation of the original instructions ENGLISH Assembly of the additional module To insert the additional module, remove the flange from the main electric fan 5-, loosening the hex socket screw on the main fan, and insert the pin of the additional fan 5- . Check that the hex socket screws of the main and additional fan are lined up, then tighten screw .5- ...

6  7      1 6 6 Nm    Translation of the original instructions ENGLISH Fasten the electronic module plate using three fastener plates and M6 hex socket screws, and fasten each fan module using two fastener plates with M6 hex socket screws per side 6-. Use the plugs provided to close the spaces between the fans 6- Insert the electric fan unit in the upper cover profile as shown in 7- . ...