Formax FD 574 Operator's Manual

Introduction : Introduces instructions for correct operation and maintenance of the machine. If these instructions are ignored, the machine may not be able to operate at optimum performance or may break down. : Introduces restrictions for correct operation of the machine. : Introduces information that is useful for operation and maintenance of the machine, or information about the machine’s performance, etc. : Indicates the page number and item containing related information. Symbols in this manual Thank you for purchasing the Cut Sheet Cutter FD 574. To ensure safe and effi cient prolonged use of this machine, read and thoroughly understand this manual before using the machine. After using this manual, be sure to keep it in a handy place to reference. PLEASE NOTE In the interests of upgrading our product, specifi cations and other data given in this manual are subject to change without notice. If the manual contains anything that you do not understand, contact the distributor or dealer for clarifi cation.

These symbols and pictures provide warnings and instructions to prevent danger to you or other personnel, and to prevent damage to offi ce property. The meanings of these symbols and pictures are explained below. Indicates a high degree of potential danger. If the warning is ignored, death or serious injury may result. Indicates a medium degree of potential danger. If the caution is ignored, medium injury or damage to property may result. A circle with a line through it indicates a prohibited action. The particular act prohibited is indicated by a picture inside the circle. (In the example shown here, the prohibited act is disassembly.) A black disc indicates an instruction, or sometimes a prohibited action. The instruction itself is indicated by pictorial symbols drawn in white on the disc. (In the example shown here, the instruction is 'Remove the plug from the outlet'.) ● Precautions for Use WARNING ● If the machine is used after foreign matter (metal fragments, water, or liquid) has entered the machine, this may result in fi re or electric shock. → Turn the power switch OFF, and then remove the power plug from the outlet. Contact the sales distributor. ● If the machine is used after heat, smoke, strange smell, or other abnormality is detected, this may result in fi re or electric shock. →Turn the power switch OFF, and then remove the power plug from the outlet. Contact the sales distributor. ● Do not insert or drop metal, fl ammable material, or other matter through the ventilation holes into the machine interior. →Doing so may result in fi re or electric shock. ● Do not place fl ower vases, fl owerpots, cups, or water containers (including metal containers) on top of the machine. →Fire or electric shock may result if liquid spills inside the machine. Notes on Safety (Please Read and Observe) WARNING CAUTION Safety Precautions

WARNING ● Use only the power cord that is provided among the accessories. Insert the power cord plug fi rmly into the socket, so that proper electrical contact is effected. Use of any other power cord could result in imperfect grounding. If grounding is imperfect and electrical leakage occurs, fi re or electric shock could result. ● Caution for Power Supply and Power Cord WARNING ● Do not use a source voltage other than that specifi ed. Do not connect two or more loads to a single outlet. →Doing so may result in fi re or electric shock. ● Be sure to remove dust on the power plug and/or the outlet. Using these without removing dust may have minute electric current fl ow to the surface due to the humidity and cause a fi re due to the heat. →It may cause a fi re or electric shock. ● Do not insert or remove the power plug with wet hands. →Doing so may result in fi re or electric shock. ● Do not damage, break, or modify the power cord. Do not place heavy objects on, tug, or unnecessarily bend the power cord. → Doing so may result in fi re or electric shock. CAUTION ● Remove the power plug itself, not the cord. → Tugging the cord may damage it (expose conductors, or cause disconnections, etc.), resulting in fi re or electric shock.

WARNING ● Do not modify the machine. →Doing so may result in fi re or electric shock. ● Do not remove the rear lid, cabinet, or covers from the machine. → The inside of the machine contains high-voltage parts, which may cause electric shock. ● Caution for Location WARNING ● Do not place the machine in a humid or dusty area. →Doing so may result in fi re or electric shock. CAUTION ● Before moving the machine, remove the power plug from the outlet. → If the cord is damaged, this may result in fi re or electric shock. ● Do not place the machine in an unstable position such as on an unsteady table or sloping area. →If the machine drops or falls over, it may result in injury. ● Do not place the machine in a place subject to direct sunlight or heating equipment such as a stove. ● Avoid placing the machine in a place subject to high or low temperature or high humidity. →The paper absorbs moisture and it may cause paper jam or creasing. ● Leave the power cord unplugged when the machine is not used for a long period. →Insulation may deteriorate and cause an electrical fi re.

CAUTION ● Before cleaning the machine, turn off the power switch and unplug the power cord. →If the machine is activated accidentally, injury may result. ● Do not use fl ammable sprays or solvents inside or near the machine. →Gas may accumulate inside the machine causing a fi re or explosion. ● Preventing Injury to Hands or Fingers WARNING ● The center slitter contains uncovered blades. Keep your hands or fi ngers off inside those. ● Use tweezers or a similar tool to remove jammed paper. Before removing jammed paper, be sure to unplug the power cord in order to prevent an electric shock.

If labels become damaged or come off, contact our service personnel. U80001 U80002A 1. 2. 3. Locations of Warning Labels

1. 1. U82313 2. Paper infeed side Open the top cover. Upper plate (front)

Notes on Safety (Please Read and Observe) ....................................ii Safety Precautions ..............................................................ii Locations of Warning Labels ..................................................vi Before Using This Machine Part Names and Their Functions ................................................. 2 Appearance (Paper Infeed Side) ............................................. 2 Appearance (Paper Ejection Side) .......................................... 3 Control Panel .................................................................... 4 LCD Panel ....................................................................... 5 Turning Power ON/OFF ............................................................. 6 Turing Power ON ............................................................... 6 Turning Power OFF ............................................................ 7 Acceptable Paper .................................................................... 8 Basic Operation Procedure for Using the Machine ................................................10 About Display Screens .............................................................11 Standby Screen ................................................................11 Menu Selection Screen .......................................................11 Function Setting Screen ......................................................12 Preparation Before Use ............................................................13 Setting the Support Tray ......................................................13 Loading the Paper .............................................................13 Adjusting Feed Pressure according to Paper Thickness ...............15 Aligning the Paper Retaining Plates ........................................16 Basic Operation .....................................................................18 Menu Selection .................................................................18 Direct Processing ..............................................................18 Standard JOB ..................................................................19 Taking Out the Cut Paper ....................................................22 Menu Selection Custom JOB .........................................................................24 Memory No. and JOB Details................................................30 Auto Cut ..............................................................................31

Function Settings ....................................................................36 1. Double Feed Detection ....................................................37 2. Slitter/Perforation ...........................................................38 3. Preset Counter .............................................................39 4. Speed ........................................................................40 5. Downstream Unit ...........................................................41 6. Cut Position Adjustment ...................................................42 7. JOB Display .................................................................43 8. Auto Power Off .............................................................45 9. Exit ............................................................................46 Optional Equipment How to Use Center Slitter Unit ....................................................48 Using as a Slitter ...............................................................48 Using as a Gutter Defl ector ..................................................49 How to Use Perforator (Standard/Micro) Unit ..................................51 Troubleshooting If Trouble Occurs ....................................................................54 When Messages Appear ...........................................................55 Corrective Action for Paper Jams ...............................................57 How to Remove Jammed Paper from Infeed Area ......................57 How to Remove Jammed Paper from Center Area or Cutter Unit ....58 Daily Maintenance Daily Maintenance ..................................................................62 Specifi cations Specifi cations ........................................................................64

Before Using This Machine This chapter contains essential information such as the names of the machine parts, the names and functions of keys on the control panel, and the acceptable paper etc. Please be sure to read this chapter carefully before using the machine. Part Names and Their Functions ..........................................................2 Appearance (Paper Infeed Side) ......................................................2 Appearance (Paper Ejection Side) ...................................................3 Control Panel .............................................................................4 LCD Panel ................................................................................5 Turning Power ON/OFF ......................................................................6 Turing Power ON ........................................................................6 Turning Power OFF .....................................................................7 Acceptable Paper .............................................................................8

Appearance (Paper Infeed Side) 1 2 3 4 5 6 7 8 9 10 No. Name Function 1 Feed tray Load paper on this tray. 2 Support tray Open this tray when loading the paper. Close the tray when not used. 3 Paper feed guides Set the position of these guides according to the width of the paper. 4 Curl stopper roller Use this to hold down the paper curl. 5 Top cover Open this cover when aligning the paper retaining plates, removing jammed paper or aligning such optional equipment as the perforator or the center slitter. The machine cannot operate with this cover opened. 6 Feed pressure lever Adjusts paper feed pressure according to paper thickness. Usually set this lever to “NORMAL PAPER”. 7 Paper set lever Lower this lever before loading the paper on the feed tray. After setting the paper properly, lift this lever for operation. 8 Paper feed roller unit Feeds the paper into the machine. 9 Power switch Press the “ I ” side of the switch to turn on the power . Press the “ O ” side of the switch to turn off the power. 10 Inlet Insert the female plug of the supplied power cord into this inlet. 11 Control panel Use the keys on this panel to operate the machine. 11 3 4

Before Using This Machine U80004B Appearance (Paper Ejection Side) 1 3 2 4 No. Name Function 1 Stacker Receives the ejected paper. 2 Ejection guide Set these guides according to the width of the paper. 3 Paper stopper Set this stopper according to the length of the paper. 4 Rear cover Open this cover to remove any paper jammed in the cutter unit. The machine cannot operate with this cover opened.

MENU OK CLEAR RETURN TEST JOG START STOP U80005E Control Panel No. Name Function 1 LCD panel Displays various messages. 2 TEST key Performs proof feed. (one sheet) 3 JOG REVERSE key The paper is fed backward slowly while this key is pressed. 4 JOG FORWARD key The paper is fed forward slowly while this key is pressed. 5 MENU LEFT key When selecting menu, pressing this key selects leftward item dis- played on the LCD. When setting number, it decrements the number. 6 MENU/OK key Displays the menu selection screen. Determines the selected setting. 7 MENU RIGHT key When selecting mode, pressing this key selects rightward item dis- played on the LCD. When setting number, it increments the number. 8 CLEAR/RETURN key Press to cancel selection or to clear the number. 9 START key Press to start operation. * This key is inactive when an error is displayed. 10 STOP key Press to stop operation. Press to return the display to the standby screen. While this key is pressed, the LCD panel displays the counter. While this key is pressed with an optional unit connected, the machine performs the optional operation. 2 3 4 5 6 7 8 9 10 1

Before Using This Machine U80000mE MENU OK CLEAR RETUR U80000mE MENU OK CLEAR RETUR LCD Panel No. Name Function 1 Counter Displays the current number of sheets that have been processed. 2 Processing mode Displays the current processing mode. 3 Settings Displays the current function settings. 4 Counter Displays the current number of sheets that have been processed and the number of sheets that is set by the Preset Counter. 1 2 3 3 2 4 •Standby Screen 123/456shts A4 3 pcs ****** 1234shts A4 3 pcs ******

let (three-slot). WARNING ● Insert the power cord plug securely into an outlet, so that proper electrical contact is effected. If grounding is imperfect and electrical leakage occurs, fi re or electric shock could result. Press the ‘ I ’ side on the power switch to turn the power ON. Insert the female plug of the power cord supplied into the ‘inlet’ on the paper infeed side of the machine. Turing Power ON Turning Power ON/OFF Outlet Male plug of the power supply cord U80505E When the power is turned ON, the LCD panel displays the screen that appeared when the power was last turned ON. Make sure that the LCD panel displays the standby screen. U80032 U80021 U80000mE MENU OK CLEAR RETUR ****** 1234shts A4 3 pcs Female plug of power cord Inlet Male plug of power cord

Before Using This Machine Turning Power OFF U80033 Press the ‘ O ’ side on the power switch to turn the power OFF. The power to the machine turns off and the panel display disappears.

Width : 106 - 364 mm (4.1764 - 14.3416 inches) Paper weight 58-157 gsm (50 - 135 kg) Feed tray capacity 500 sheets (paper weight : 55 kg/64 gsm, bond paper) Capacity varies depending on paper alignment or curl. The following types of paper cannot be used. * Paper with fi le-binding holes * Paper with staples and/or clips attached * Paper with markedly curling ends/sides, or folds * Carbon-backed paper * Paper with smaller pieces of glued paper * Paper with glue or adhesive applied to sticker or label and so on.

out the cut paper. Procedure for Using the Machine ........................................................ 10 About Display Screens ......................................................................11 Standby Screen .........................................................................11 Menu Selection Screen ................................................................11 Function Setting Screen .............................................................. 12 Preparation Before Use .................................................................... 13 Setting the Support Tray .............................................................. 13 Loading the Paper ..................................................................... 13 Adjusting Feed Pressure according to Paper Thickness ....................... 15 Aligning the Paper Retaining Plates ................................................ 16 Basic Operation ............................................................................. 18 Menu Selection ......................................................................... 18 Direct Processing ...................................................................... 18 Standard JOB .......................................................................... 19 Taking Out the Cut Paper ............................................................ 22

Preparation Before Use..............Setting the Support Tray (→ P.13) Loading the Paper (→ P.13) Adjusting Feed Pressure according to Paper Thickness (→ P.15) Aligning the Paper Retaining Plates (→ P.16) Turning Power ON........................Turning Power ON/OFF (→ P.6) (When you install the options, perform the setting.) Selecting Direct Processing (→ P.11, P.18 ) Select from among processing mode displayed on the LCD panel. Select from the menu Standard JOB (→ P.19) Custom JOB (→ P.24) Auto Cut (→ P.31) Function Settings (→ P.36) Function Settings 1. Double Feed Detection (→ P.37) 2. Slitter/Perforation (→ P.38) 3. Preset Counter (→ P.39) 4. Speed (→ P.40) 5. Downstream Unit (→ P.41) 6. Cut Position Adjustment (→ P.42) 7. JOB Display (→ P.43) 8. Auto Power Off (→ P.45) 9. Exit (→ P.46) Operation fi nishes. Taking Out the Cut Paper (→ P.22) Operation starts.

displays the screen that appeared when the power was last turned ON. ● Selecting Direct Processing Each time you press the MENU LEFT key or MENU RIGHT key, the LCD panel sequentially displays the processing mode previously used. Display the processing mode that you want to use and press the START key. Operation starts. If you press the TEST key, proof feed (one sheet) is performed. When the standby screen is displayed, press the MENU/OK key. The menu selection screen appears. Press the MENU LEFT key or MENU RIGHT key to select menu (Standard, Custom, Auto Cut, Func. Set) and press the MENU/OK key. If you press the CLEAR/RETURN key or STOP key when the menu selection screen appears, the display returns to the standby screen. Standby Screen Menu Selection Screen About Display Screens U80000mE MENU OK CLEAR RETUR U80000qE MENU OK CLEAR RETUR Standard Custom Auto Cut Func. Set ****** ****** 1234shts A4 3 pcs 1234shts A4 3 pcs

Function Setting Screen When the menu selection screen is displayed, select ‘Func. Set’ and press the MENU/OK key. The function setting screen appears. Each time you press the MENU RIGHT key, the following function settings appear in order. 1. DBL FD detect. (Double feed detection) 2. SLT/PER (Slitter/Perforation) 3. Preset counter 4. Speed 5. Downstream unit 6. Cut pos. adj. (Cut position adjustment) 7. JOB display 8. Auto power off 9. Exit (Returns to the menu selection screen) Each time you press the MENU LEFT key, the above function settings appear in reverse order. Display the function setting that you want to use and press the MENU/OK key. If you press the CLEAR/RETURN key when the function setting screen is displayed, the display returns to the menu selection screen. If you press the STOP key when the function setting screen is displayed, the display returns to the standby screen. ► U80000E MENU OK CLEAR RETUR Function(1/9) 1. DBL FD detect.

Lower the paper set lever. Loosen the fi xing screws of the paper feed guides to move the paper feed guides to each side. Take a stack of paper, fl ip through it to loosen up sheets, and straighten up the edges of the stack on a level surface. Be sure to loosen up the paper sheets before load- ing the stack on the tray. Otherwise, paper feed errors or jams may occur. U80025 Preparation Before Use Setting the Support Tray Loading the Paper The following describes preparation before use. U80023 U80024 Paper feed guides Paper set lever

Load the paper on the feed tray. Position the paper feed guides according to the paper width and secure with the fi xing screws. Position the paper approximately in the middle of the feed tray. Otherwise, the paper may not be fed in a straight line, resulting in paper feed errors or jams. Raise the paper set lever. Put down the curl stopper rollers on the paper. U80025B U80026A U80026B

Basic Operation Adjusting Feed Pressure according to Paper Thickness Set the feed pressure lever according to the paper thickness. The ‘NORMAL PAPER’ position is the reference position. ● For thin paper: Set the feed pressure lever to the ‘LIGHT PAPER’ position. ● For thick paper: Set the feed pressure lever to the ‘HEAVY PAPER’ position. In the following cases, adjust the feed pressure according to the feeding condition of the paper. ● If two or more sheets of paper are fed at one time: Set the lever to the ‘LIGHT PAPER’ position, or lower the lever one rank from the present position. ● If no paper is fed due to slips: Set the lever to the ‘HEAVY PAPER’ position, or raise the lever one rank from the present position. U80027e HEAVY PAPER NORMAL PAPER LIGHT PAPER

U80034 U80029 U80028 Aligning the Paper Retaining Plates Open the top cover. Loosen the four thumbscrews and move the paper retaining plates as shown below. ● Two outer plates: Move each of them to each end of the paper. ● Two inner plates: Move them so that they are evenly spaced between the outer plates. Be sure to place the four slide plates under the paper retaining plates. After positioning the plates, secure them with the thumbscrews. When using any of the following options, follow the instructions in chapter 5. ● Center slitter unit ● Perforator (standard/micro) unit U80030 Top cover Thumbscrews Paper retaining plates Slide plates Paper feed side Slide plates

screen. Each time you press the MENU LEFT key or MENU RIGHT key, the LCD panel sequentially displays the processing mode previously used. Display the processing mode that you want to use and press the START key to perform the processing. All the papers loaded on the feed tray are processed. To stop the operation, press the STOP key. If you press the TEST key, proof feed (one sheet)is performed. When you want to specify the number of sheets to process, refer to ‘3. Preset Counter’ in chapter 4. Direct Processing Processing modes previously used are displayed on the standby screen. You can use the displayed processing mode to easily perform processing without a new setting. ● Direct Processing: → P.18 ● Standard JOB: → P.19 ● Custom JOB: → P.24 ● Auto Cut: → P.31 ● Function Settings: → P.36 U80000mE MENU OK CLEAR RETUR U80000qE MENU OK CLEAR RETUR ****** ****** 1234shts A4 3 pcs 1234shts A4 3 pcs

screen. (Right fi gure: Standby screen The preset counter is not set.) Press the MENU/OK key to display the menu selection screen. ‘Press MENU key to select cut.’ appears only on the initial screen at the time when you fi rst turn on the machine. Press the MENU/OK key. Then follow step . (Right fi gure: Initial screen (factory setting)) Press the MENU LEFT key or MENU RIGHT key to select ‘Standard’ and press the MENU/OK key. (Right fi gure: Menu selection screen) If you press the STOP key or CLEAR/RETURN key, the display returns to the standby screen. You can select paper size and the number of pieces from the pre-programmed data. U80000kE MENU CLEAR RETUR U80000kE MENU CLEAR RETUR U80000mE MENU OK CLEAR RETUR Press MENU/OK key to select cut. Standard Custom Auto Cut Func. Set ****** 1234shts A4 3 pcs

You can select from among A3, A4, A5, B4, B5, 14 inches, 11 inches, and 8.5 inches. Press the MENU LEFT key or MENU RIGHT key to select paper size and press the MENU/OK key. If you press the CLEAR/RETURN key, the display returns to the menu selection screen. If you press the STOP key, the display returns to the standby screen. Select paper orientation. Press the MENU LEFT key or the MENU RIGHT key to select paper orientation and press the MENU/OK key. If you press the CLEAR/RETURN key, the display returns to the previous screen in step . If you press the STOP key, the display returns to the standby screen. Paper orientation for A3 paper is ‘→‘ only. You cannot select paper orientation for A3 size. → → U80000dE MENU OK CLEAR RETUR ► ► P aper s iz e ? P aper orient at ion? A4

● Settable number of pieces No Cut A3 : 2 to 7 pcs. A4 : 2 to 5 pcs. A4R : 2 to 3 pcs. A5 : 2 to 3 pcs. A5R : 2 pcs. B4 : 2 to 6 pcs. B4R : 2 to 4 pcs. B5 : 2 to 4 pcs. B5R : 2 to 3 pcs. 14 inches : 2 to 6 pcs. 11 inches : 2 to 5 pcs. 8.5 inches : 2 to 4 pcs. Press the MENU LEFT key or MENU RIGHT key to select the number of pieces and press the MENU/OK key. If you press the CLEAR/RETURN key, the display returns to the previous screen in step . The setting that was just made appears on the LCD panel. 1. If you press the TEST key, proof feed (one sheet) is performed. Check whether the sheet is correctly cut. • To cut paper in custom dimensions, refer to ‘ Saving’ of ‘Custom JOB’ in chapter 3. • To make a fi ne adjustment of cut position, refer to ‘6. Cut Position Adjustment’ in chapter 4. U80202Ie TEST A4 3 pcs 1234shts MENU OK CLEAR RETURN U80000iE MENU OK CLEAR RETUR C u t i n t o ? 3pcs

All the papers loaded on the feed tray are processed. To stop the operation, press the STOP key. When you want to specify the number of sheets, refer to ‘3. Preset Counter’ in chapter 4. Take out the cut papers from the stacker. ● If the stacker becomes full during operation Press the STOP key to stop the operation and take out the cut papers from the stacker. Then press the START key to resume the operation. Taking Out the Cut Paper U80202H

in chapter 2. Custom JOB ................................................................................. 24 Memory No. and JOB Details........................................................ 30 Auto Cut ...................................................................................... 31

that you want to set, and retrieve the memory No. When the standby screen is displayed, press the MENU/OK key to display the menu selection screen. (Right fi gure: Menu selection screen) Press the MENU LEFT key or MENU RIGHT key to select ‘Custom’ and press the MENU/ OK key. (Right fi gure: ‘Custom’ is selected.) If you press the CLEAR/RETURN key or STOP key, the display returns to the standby screen. Press the MENU LEFT key or MENU RIGHT key to select the processing mode and press the MENU/OK key. RTRV: Retrieves saved custom JOB. Go to step . SAVE: Saves new custom JOB. Go to step . DLT: Deletes saved custom JOB. Go to step . If you press the CLEAR/RETURN key, the display returns to the menu selection screen. If you press the STOP key, the display returns to the standby screen. ► U80000E MENU OK CLEAR RETUR U80000dE MENU OK CLEAR RETUR Standard Custom Auto Cut Func. Set Custom JOB RTRV SAVE DLT Standard Custom Auto Cut Func. Set

MENU LEFT key or MENU RIGHT key, memory no., number of pieces, and paper length sequentially appear. Display the memory no. that you want to select and press the MENU/OK key. If no JOB is saved, ‘Unsaved’ appears. If you press the CLEAR/RETURN key, the display returns to the previous screen in step . If you press the STOP key, the display returns to the standby screen. 2. The selected JOB appears. If you press the TEST key, proof feed (one sheet) is performed. If you press the START key, the operation starts. Saving 1. Press the MENU LEFT key or MENU RIGHT key to select the memory no. to save and press the MENU/OK key. You can save up to 100 JOBs (M00 to M99). 2. If no JOB is saved, ‘M** Unsaved’ appears. U80000lE MENU OK CLEAR RETUR U80000mE MENU OK CLEAR RETUR U80000dE MENU OK CLEAR RETUR U80000dE MENU OK CLEAR RETUR Retrieve JOB M00: 3: 297.0mm 1234shts M00: 3:297.0mm ****** Select JOB No. M** Saved M** Unsaved Select JOB No.

appears. When you select a memory no. that is already saved, ‘Saved JOB’ appears. To overwrite the data, press the MENU LEFT key or MENU RIGHT key to select ‘Overwrite’ and press the MENU/OK key. To save the data with different memory no., select ‘Cancel’ and press the MENU/OK key. 4. Press the MENU LEFT key or MENU RIGHT key to set the paper length (mm). Each time you press the MENU RIGHT key, the value increases in increments of 0.1 mm. Each time you press the MENU LEFT key, the value decreases in increments of 0.1 mm. You can set the value in the range of 110.0 to 420.0 mm. After setting is complete, press the MENU/OK key. 5. Press the MENU LEFT key or MENU RIGHT key to set the distance from the paper leading edge to the fi rst cut position. After setting is complete, press the MENU/OK key. ► ► . ► U80000dE MENU OK CLEAR RETUR U80000dE MENU OK CLEAR RETUR U80000oE MENU OK CLEAR RETUR U80000oE MENU OK CLEAR RETUR Saved JOB Overwrite Cancel Paper length ? *** *mm . Cut No.1 length? Select JOB No. M** Saved *** *mm .

First cut First cut +17.1mm positon First cutt positon +54.9mm This area is not available. This area is not available. 55.0mm from 17.0mm from edge edge the trailing the trailing You can set cut position in the range of ‘0.1 to (paper length-0.1 mm)’ except for the following ranges. Unavailable ranges: • 17.1 to 54.9 mm from the leading edge of the paper • 17.0 to 55.0 mm from the trailing edge of the paper 6. Press the MENU LEFT key or MENU RIGHT key to set the distance from the paper leading edge to the second cut position. After setting is complete, press the MENU/OK key. You can set cut position in the range of ‘(fi rst cut position+0.1) to (paper length-0.1 mm)’ except for the following ranges. Unavailable ranges: • (fi rst cut position+17.1) to (fi rst cut position +54.9 mm)’ * 17.0 to 55.0 mm from the trailing edge of the paper If you do not set the second cut, enter ‘0.0 mm’ and press the MENU/OK key. The ‘Save ?’ screen in step appears. U80263e Paper feed direction 17.1mm from the leading edge edge edge 54.9mm from the leading edge 55.0mm from the trailing 17.0mm from the trailing This area is not available. This area is not available.

same way as step 6. After each setting is complete, press the MENU/ OK key. After the last cut position is set, enter ‘0.0 mm’ and press the MENU/OK key. 8. Press the MENU LEFT key or MENU RIGHT key to select whether to save the JOB (Yes) or not (No). If you select ‘Yes’ and press the MENU/OK key, the data is saved with the memory no. currently selected. If you select ‘No’ and press the MENU/OK key, the data is not saved and the display returns to the screen in step 1. If you press the CLEAR/RETURN key in the middle of the saving procedure, the display returns to the previous one. If you press the STOP key, the data is not saved and the display returns to the standby screen. 9. The right screen appears and the data is saved. ► U80000E MENU OK CLEAR RETUR U80000kE MENU CLEAR RETUR U80000kE MENU CLEAR RETUR Cut No.* length? 0.0 mm Save ? Yes No ► Saving Please wait

MENU LEFT key or MENU RIGHT key to select the memory no. that you want to delete. Then press the MENU/OK key. If no data is saved, ‘Unsaved’ appears. 2. ‘M** Clear?‘ appears. 3. If you select ‘Yes’ and press the MENU/OK key, ‘Clearing’ appears. Then the selected memory no. is deleted and the ‘Custom JOB’ screen appears. If you select ‘No’ and press the MENU/OK key, the memory no. is not deleted and the display returns to the screen in step 1. U80000dE MENU OK CLEAR RETUR U80000dE MENU OK CLEAR RETUR U80000oE MENU OK CLEAR RETUR U80000E MENU OK CLEAR RETUR U80000dE MENU OK CLEAR RETUR M** Clear ? Yes No Clearing Please wait M** Unsaved Select JOB No. Select JOB No. M** Saved Select JOB No. ** Saved M

Memory No. Paper Length Cut No.1 Cut No.2 Cut No.3 Cut No.4 Cut No.5 Cut No.6 Cut No.7 You can use the form below for your convenience.

and performs cut operation by specifying the number of cuts. When the LCD panel displays the standby screen, press the MENU/OK key to display the menu selection screen. (Right fi gure: Menu selection screen) Press the MENU LEFT key or MENU RIGHT key to select ‘Auto Cut’ and press the MENU/OK key. (Right fi gure: ‘Auto Cut’ is selected.) If you press the CLEAR/RETURN key or the STOP key, the display returns to the standby screen. Load the paper on the feed tray and press the MENU/OK key. If an optional center slitter unit, perforator (standard) unit, or perforator (micro) unit is installed, move the ‘upper blade unit’ to either side. Otherwise the paper will be cut. If an optional straight conveyor is connected, lift up the ‘roller unit’ so that the measured paper does not bend when ejected. U82016 U80000E MENU OK CLEAR RETUR U80000kE MENU CLEAR RETUR U80000kE MENU CLEAR RETUR Standard Custom Auto Cut Func. Set Standard Custom Auto Cut Func. Set Load paper and press MENU/OK key.

ber of pieces to be cut and press the MENU/OK key. ● Settable number of pieces 420.0 mm (A3) : 2 to 7 pcs. 297.0 mm (A4) : 2 to 5 pcs. 210.0 mm (A4R) : 2 to 3 pcs. 210.0 mm (A5) : 2 to 3 pcs. 148.5 mm (A5R) : 2 pcs. 364.0 mm (B4) : 2 to 6 pcs. 257.0 mm (B4R) : 2 to 4 pcs. 257.0 mm (B5) : 2 to 4 pcs. 182.0 mm (B5R) : 2 to 3 pcs. 14 inches : 2 to 6 pcs. 11 inches : 2 to 5 pcs. 8.5 inches : 2 to 4 pcs . ‘Measuring’ appears. A single sheet of paper is fed into the machine and paper length is measured, and the paper is ejected into the stacker without cutting. ► Error message appears and operation cannot be performed in the following cases. ● No paper is loaded. → “Load paper.” ● The paper set lever is at the lower position. → “Raise paper set lever.” ● Paper remains in the machine. → “Remove paper from infeed area.” “Remove paper from cut area.” ● Paper jam → “Remove paper from ** area.” ● Paper length does not meet the specifi cations. (other than 110.0 to 420.0 mm) → “Paper is out of specifi cation.” ● The cover is open. → “Top cover is open.” “Rear cover is open.” Measured length appears for a few seconds. U80000E MENU OK CLEAR RETUR U80000E MENU OK CLEAR RETUR U80000dE MENU OK CLEAR RETUR Length : 297.0mm Please wait Cut int o ? 2pcs Measuring Please wait

All the papers loaded on the feed tray are processed. To stop the operation, press the STOP key. ● When you want to specify the number of sheets, refer to “3. Preset Counter” in chapter 4. 2. In any of the following cases, saved automatic cut data is deleted. ● When cut dimensions are manually changed using the MENU LEFT key or MENU RIGHT key. ● When cut dimensions are changed by selecting ‘Standard JOB’ or ‘Retrieve JOB’. ● When the power is turned off. Saving 1. Press the MENU LEFT key or MENU RIGHT key to select memory no. and press the MENU/OK key. If you select saved memory no., go to step 2. If you select unsaved memory no, go to step 3. Press the MENU LEFT key or MENU RIGHT key to select ‘Start’ or ‘Save’ and press the MENU/ OK key. If you select ‘Start’, go to step . If you select ‘Save’, go to step . ► ► ► U80000dE MENU OK CLEAR RETUR U80000dE MENU OK CLEAR RETURN U80000E MENU OK CLEAR RETUR Start operation ? Start Save Auto 3pcs 1234shts Select JOB No. M** Saved

confi rming display whether to overwrite the data appears. Press the MENU LEFT key or MENU RIGHT key to select ‘Overwrite’ or ‘Cancel’ and press the MENU/OK key. If you select ‘Cancel’ and press the MENU/OK key, the display returns to the previous screen without deleting the selected memory no. If you select ‘Overwrite’ and press the MENU/OK key, the saved data is overwritten. Go to step 4. (Right fi gure: ‘Saving’ screen) 3. When you select unsaved memory no., the data is saved. (Right fi gure: ‘Saving’ screen) 4. After saving is complete, the job details of the saved memory no. appear. If you press the START key, operation starts. If you press the MENU/OK key, menu selection screen appears. U80000mE MENU OK CLEAR RETUR U80000dE MENU OK CLEAR RETUR U80000E MENU OK CLEAR RETUR U80000E MENU OK CLEAR RETUR Saved JOB Overwrite Cancel Saving Please wait Saving Please wait 1234shts M00: 3:297.0mm ******

Using Useful Functions Using Useful Functions This chapter describes operations using useful functions. You can use useful functions depending on your needs. Function Settings ............................................................................ 36 1. Double Feed Detection ............................................................ 37 2. Slitter/Perforation ................................................................... 38 3. Preset Counter ..................................................................... 39 4. Speed ................................................................................ 40 5. Downstream Unit ................................................................... 41 6. Cut Position Adjustment ........................................................... 42 7. JOB Display ......................................................................... 43 8. Auto Power Off ..................................................................... 45 9. Exit .................................................................................... 46

MENU/OK key. The menu selection screen appears. Press the MENU LEFT key or MENU RIGHT key to select ‘Func. Set’ and press the MENU/OK key. If you press the CLEAR/RETURN key or STOP key, the display returns to the standby screen. The function setting screen appears. Press the MENU LEFT key or MENU RIGHT key to select function that you want to use. Functions appear in the following order. 1. DBL FD detect. ...... → P.37 2. SLT/PFR ................ → P.38 3. Preset counter ....... → P.39 4. Speed .................... → P.40 5. Downstream unit ... → P.41 6. Cut pos. adj. .......... → P.42 7. JOB display ........... → P.43 8. Auto power off ....... → P.45 9. Exit ........................ → P.46 Press the MENU/OK key. When each function setting is complete, the display returns to the function setting screen. If you press the CLEAR/RETURN key, the display returns to the menu selection screen. If you press the START key, the display returns to the standby screen. Function Settings U80000dE MENU OK CLEAR RETUR ► The following describes how to select function. U80000mE MENU OK CLEAR RETUR ****** 1234shts A4 3 pcs Standard Custom Auto Cut Func. Set Function(1/9) 1. DBL FD detect.

Function Settings Press the MENU LEFT key or MENU RIGHT key to select double feed detection level. OFF: Set to ‘Off’ when double feed detection is not used. Min: Set to ‘Min’ when ‘Double Feed’ appears even though double feed does not occur. Mid: Standard Factory setting is ‘Mid’. Max: Set to ‘Max’ when double feed is not detected even though double feed occurs. Press the MENU/OK key. The setting is determined and the display returns to the function setting screen in step . If you press the CLEAR/RETURN key, the display returns to the function setting screen without determining the setting. If you press the STOP key, the display returns to the standby screen without determining the setting. 1. Double Feed Detection This sets double feed detection according to the paper that you are using. Default setting is ‘Mid’ (middle level). ► The following describes how to set each function. U80000oE MENU OK CLEAR RETUR U80000kE MENU CLEAR RETUR Select ‘1. DBL FD detect.’ on the function setting screen and press the MENU/OK key. If you press the CLEAR/RETURN key, the display returns to the menu selection screen. If you press the STOP key, the display returns to the standby screen. DBL FD detect. Off Min Mid Max Function(1/9) 1. DBL FD detect.

function setting screen in step . Select ‘2. SLT/PFR’ on the function setting screen and press the MENU/OK key. If you press the CLEAR/RETURN key, the display returns to the menu selection screen. If you press the STOP key, the display returns to the standby screen. When you use a center slitter unit or perforator (standard/micro) unit, press the MENU RIGHT key to select ‘ON’ and press the MENU/OK key. If the center slitter unit or perforator (standard/ (micro) unit is not installed, select ‘OFF’ and press the MENU/OK key. If you press the CLEAR/RETURN key, the display returns to the function setting screen in step . If you press the STOP key, the display returns to the standby screen. This function is set when a center slitter unit (optional) or perforator (standard/micro) unit (optional) is connected. When ‘ON’ is selected: If you press the TEST key once, the paper stops in front of the slitter and you can check slit position by pressing the JOG REVERSE key or JOG FORWARD key. Pressing the TEST key again performs proof feed (one sheet). When ‘OFF’ is selected: If you press the TEST key once, proof feed (one sheet) is performed. You cannot check slit position. Default setting is ‘OFF’. 2. Slitter/Perforation U80000oE MENU OK CLEAR RETUR ► Function(2/9) ► 2.SLT/PFR U80000kE MENU CLEAR RETUR SLT / PFR OFF ON

Function Settings This function stops processing by the specifi ed number of sheets. When you want to perform continuous processing, set the counter to ‘0’. Default setting is ‘0’. Press the MENU/OK key. The setting is determined and the display returns to the function setting screen in step . If you press the CLEAR/RETURN key, the display returns to the function setting screen without determining the setting. If you press the STOP key, the display returns to the standby screen. (Right fi gure: Standby screen after setting ‘Preset counter’.) If you press the CLEAR/RETURN key or STOP key when the menu selection screen appears, the display returns to the standby screen. Press the MENU RIGHT key to increase the number of sheets. Default setting is ‘0’. You can set up to ‘999’. To decrease the number, press the MENU LEFT key. Continuously pressing the MENU LEFT key or MENU RIGHT key decreases or increases the number continuously. Pressing the CLEAR/RETURN key for a longer time sets the number to ‘0’. 3. Preset Counter ► Function(3/9) ► 3. Preset counter ► Select ‘3. Preset counter’ on the function setting screen and press the MENU/OK key. If you press the CLEAR/RETURN key, the display returns to the menu selection screen. If you press the STOP key, the display returns to the standby screen. U80000cE MENU OK CLEAR RETUR U80000oE MENU OK CLEAR RETUR U80000kE MENU CLEAR RETUR Preset counter 123shts A4 3 pcs 123/456shts ******

function setting screen in step . Press the MENU LEFT key or MENU RIGHT key to select speed and press the MENU/OK key. If you press the CLEAR/RETURN key, the display returns to the function setting screen in step . If you press the STOP key, the display returns to the standby screen. This function sets processing speed of the machine. Default setting is ‘Mid’ (middle speed). 4. Speed U80000bE MENU OK CLEAR RETUR U80000kE MENU CLEAR RETUR Function(4/9) ► 4.Speed ► Select ‘4. Speed’ on the function setting screen and press the MENU/OK key. If you press the CLEAR/RETURN key, the display returns to the menu selection screen. If you press the STOP key, the display returns to the standby screen. Speed High Mid Low

Function Settings After setting is complete, the display returns to the function setting screen in step . This function is set when an optional straight conveyor is connected. The connected optional unit is automatically recognized. However, you can change the setting manually. • If the power to the machine is on when the optional unit is connected, the optional unit is not recognized automatically. Be sure to turn off the power before connecting the optional unit. • If no optional unit is connected, ‘Stacker’ is set. 5. Downstream Unit U80000iE MENU OK CLEAR RETUR U80000kE MENU CLEAR RETUR Function(5/9) ► 5.Downstream unit ► Press the MENU LEFT key or MENU RIGHT key to select ‘Straight CNV’ and press the MENU/OK key. If you press the CLEAR/RETURN key, the display returns to the function setting screen in step . If you press the STOP key, the display returns to the standby screen. If you turn off the power, remove the optional unit, and then turn on the power again, ‘Stacker’ is automatically selected. Select ‘5. Downstream unit’ on the function setting screen and press the MENU/OK key. If you press the CLEAR/RETURN key, the display returns to the menu selection screen. If you press the STOP key, the display returns to the standby screen. Downstream unit Stacker

MENU RIGHT key to set value and press the MENU/OK key. You can set in the range of ‘-15.0’ to ‘+15.0’ mm. Pressing the MENU RIGHT key once increases the value by 0.1 mm. Pressing the MENU LEFT key once decreases the value by 0.1 mm. Pressing the CLEAR/RETURN key for a longer time sets the value ‘0’. (Right fi gure: Setting that shifts cut position by 12.3 mm backward.) If you press the CLEAR/RETURN key, the display returns to the function setting screen in step . If you press the STOP key, the display returns to the standby screen. 6. Cut Position Adjustment ► ► ► ► ► This function shifts cut position for value set on Cut Position Adjustment (Cut pos. adj.) screen. + (plus) setting shifts cut position backward for value from the paper leading edge. - (minus) setting shifts cut position forward for value from the paper leading edge. Default setting is ‘0.0 mm’. Select ‘6. Cut pos. adj.’ on the function setting screen and press the MENU/OK key. If you press the CLEAR/RETURN key, the display returns to the menu selection screen. If you press the STOP key, the display returns to the standby screen. After setting is complete, the display returns to the function setting screen in step . U80000kE MENU CLEAR RETUR U80000kE MENU CLEAR RETUR U80000oE MENU OK CLEAR RETUR Cut pos. adj. 0.0mm Function(6/9) 6.Cut pos . adj. Cut pos. adj. +12.3mm

Function Settings and marks on the LCD panel move to each side of ‘ON OFF’ and it enables you to select ‘ON’ or ‘OFF’. Press the MENU LEFT key or MENU RIGHT key to select processing mode and press the MENU/OK key. (Right fi gure: ‘A4 2 pcs’ is selected.) If you press the CLEAR/RETURN key, the display returns to the function setting screen in step . If you press the STOP key, the display returns to the standby screen. 7. JOB Display ► ► ► ► ► ► Setting the display of processing mode (JOB details) that you do not use to ‘OFF’ (not displayed) enables you to search processing mode easier. However, you cannot set the display of saved Custom JOB to ‘OFF’. Even if you set the display to ‘OFF’, if you select and perform the processing mode (JOB details) in Standard JOB setting, the display setting is changed to ‘ON’ (displayed). Select ‘7. JOB display’ on the function setting screen and press the MENU/OK key. If you press the CLEAR/RETURN key, the display returns to the menu selection screen. If you press the STOP key, the display returns to the standby screen. U80000kE MENU CLEAR RETUR U80000dE MENU OK CLEAR RETUR U80000E MENU OK CLEAR RETUR ON OFF A4 2 pcs Function(7/9) 7.JOB display ON OFF A4 2 pcs

processing mode selection screen in step . To continue the setting, repeat from step . To finish the setting, press the CLEAR/RETURN key. The display returns to the function setting screen in step . Press the MENU LEFT key or MENU RIGHT key to select ‘ON’ or ‘OFF’ and press the MENU/OK key. (Right fi gure: ‘OFF’ is selected.) If you press the CLEAR/RETURN key, the display returns to the function setting screen in step . If you press the STOP key, the display returns to the standby screen. U80000kE MENU CLEAR RETUR ► ► ON OFF A4 2 pcs

Function Settings ‘Setting time’ appears on the LCD panel. You can select setting time from among 0, 5, 15, 30 and 60 minutes. Press the MENU LEFT key or MENU RIGHT key to select setting time and then press the MENU/OK key. Selecting ‘0’ means that you do not use Auto power off function. If you press the CLEAR/RETURN key, the display returns to the function setting screen in step . If you press the STOP key, the display return to the standby screen. After setting is complete, the display returns to the function setting screen in step . 8. Auto Power Off This function automatically turns off the power to the machine if you do not touch the control panel for a certain period of time. Default setting is ‘15 minutes’. Select ‘8. Auto power off’ on the function setting screen and press the MENU/OK key. If you press the CLEAR/RETURN key, the display returns to the menu selection screen. If you press the STOP key, the display returns to the standby screen. ► ► U80000lE MENU OK CLEAR RETUR U80000kE MENU CLEAR RETUR 0 5 15 30 60min. Auto power off Function(8/9) 8.Auto power off

► This fi nishes function setting. Select ‘9. Exit’ on the function setting screen and press the MENU/OK key. The display returns to the menu selection screen. U80000kE MENU CLEAR RETUR

(standard/micro) unit installed. How to Use Center Slitter Unit ............................................................ 48 Using as a Slitter ....................................................................... 48 Using as a Gutter Defl ector .......................................................... 49 How to Use Perforator (Standard/Micro) Unit .......................................... 51

U80401 Open the top cover and loosen the two hexagon socket set screws in the collars with the hexagon wrench supplied. Move the lower blade unit to the cut position and tighten the hexagon socket set screws with the hexagon wrench. Loosen the thumbscrew on the upper blade unit. Move the upper blade unit to the lower blade unit (cut position). Press the upper blade unit against the lower blade unit approx. 2 mm beyond the position where the upper blade touches the lower blade, and horizontally secure the unit with the thumbscrew. Refer to ‘2. Slitter/Perforation’ in chapter 4 to set the ‘SLT/PFR’ to ‘ON’. Close the top cover and select processing mode, and then press the TEST key. Paper is fed forward to the position of the upper guide unit. Use the JOG FORWARD key and JOG REVERSE key to check the cut position. JOG FORWARD key: Feeds the paper forward slowly. JOG REVERSE key: Feeds the paper backward slowly. How to Use Center Slitter Unit Using as a Slitter WARNING • Take extreme care to keep your hands off the upper and lower blades of the center slitter unit. → These exposed blades can injure you. U80402 Spring Top cover Lower blade unit Thumb- screw Press approx. 2 mm Upper blade Triangle label Collar Lower blade Collar Lower blade unit Upper guide unit

Optional Equipment Press the TEST key again. Proof feed (one sheet) is performed. Check whether it is correctly cut. The following describes how to use the center slitter as a gutter defl ector. (Example: in case of left side) Open the top cover and move the two left-hand side plates attached to the lower guide unit to the left edge. Loosen the two thumbscrews on the two left-hand paper retaining plates that are attached to the upper guide unit. Then move the two paper retaining plates to the left edge, aligning to the slide plates moved in step . Loosen the two hexagon socket set screws in the two collars with the hexagon wrench supplied. Move the lower blade unit to the position where the cut papers are defl ected and then tighten the two hexagon socket set screws with the hexagon wrench. Press the upper blade unit against the lower blade unit approx. 2 mm beyond the position where the upper blade touches the lower blade, and horizontally secure the unit with the thumbscrew. Attach the R guide unit to the shaft of the upper guide unit, aligning the R guide unit to the left side of the upper blade unit. Minimum gutter width of R guide unit (gutter guide): 20.0 mm Processable minimum paper width of R guide unit (gutter guide): 148.5 mm (A5) U80405 U80402 U80404 Using as a Gutter Defl ector Paper retaining plates Slide plate U80202Ie TEST A4 3 pcs 1234shts MENU OK CLEAR RETURN Thumb- screw Press for approx. 2 mm Collar Lower blade Spring Collar Upper blade Triangle label Lower blade unit Upper blade unit R guide unit

U80406 Refer to ‘2. Slitter/Perforation’ in chapter 4 to set the ‘SLT/PFR’ to ‘ON’. Close the top cover and select ‘No Cut’ on the processing menu screen, and then press the TEST key. The paper is fed forward to the position of the upper guide unit. Use the JOG FORWARD key and JOG REVERSE key to check the cut position. JOG FORWARD key: Feeds the paper forward slowly. JOG REVERSE key: Feeds the paper backward slowly. Press the TEST key again. Proof feed (one sheet) is performed. Check whether it is correctly cut. Paper Upper blade unit R guide unit

set screws on the cylinder with the hexagon wrench supplied. Move the cylinder to the perforating position and tighten the hexagon socket set screw with the hexagon wrench so that the screw perpendicularly touches the fl at surface of the D-shaped cut of the shaft to which the cylinder is attached. Loosen the thumbscrew of the perforator unit. Move the perforator unit to the perforating position. Secure the perforator unit with the thumbscrew, keeping the perforator unit in a horizontal position. Turn the pressure adjustment knob to adjust the pressure so that the perforation blade touches the cylinder. If it is getting harder to cut the paper, gradually increase the pressure. If perforations cannot be made even if the knob is turned to the ‘HIGH’ position, replace the perforation blade. Turn the pressure adjustment knob to the ‘HIGH’ direction until the paper can be cut. Applying too heavy force will wear the blade earlier. WARNING D0 not touch blade U80411 U80407 LOW HIGH U80401 WARNING • Take extreme care to keep your hands off the upper blade of the perforator (standard/micro) unit. → This exposed blade can injure you. How to Use Perforator (Standard/Micro) Unit Pressure adj. knob Thumbscrew Cylinder Perfora- tion blade Thumb- screw Pressure adj. knob Cylinder Top cover

Refer to ‘2. Slitter/Perforation’ in chapter 4 to set the ‘SLT/PFR’ to ‘ON’. Close the top cover and select processing mode, and then press the TEST key. The paper is fed forward to the position of the upper guide unit. Use the JOG FORWARD key and JOG REVERSE key to check the cut position. JOG FORWARD key: Feeds the paper forward slowly. JOG REVERSE key: Feeds the paper backward slowly. Press the TEST key again. Proof feed (one sheet) is performed. Check whether perforations are correctly made. U80202Ie TEST A4 3 pcs 1234shts MENU OK CLEAR RETURN

with paper jams and error messages. Troubleshooting If Trouble Occurs ............................................................................ 54 When Messages Appear ................................................................... 55 Corrective Action for Paper Jams ....................................................... 57 How to Remove Jammed Paper from Infeed Area .............................. 57 How to Remove Jammed Paper from Center Area or Cutter Unit ............ 58

Failures may result from various causes. Listed below are major symptoms along with corresponding check points and corrective actions. See the reference pages for more information on the respective corrective actions. Contact service personnel if any symptom is not cleared by the corrective action. Symptom Check Point Corrective Action Page Turning ON the power switch will not supply the power. Is the plug of the power cord connected? Connect the plug of the power cord correctly. P.6 The machine does not operate even when the START key is pressed. Is the top cover closed? Close the top cover. ─ Is the rear cover attached? Attach the rear cover. ─ Is the feed tray raised? Raise the paper set lever. P.13 Isn’t paper jammed? Check the JAM message on the LCD panel, and remove the jammed paper. P.55 Paper is not cut properly. Is paper size set correctly? Set the paper size correctly. P.19 others Is paper thickness correct? Use paper with thickness speci- fi ed in the specifi cation. P.8 Paper is not fed straight. Is the paper positioned in the middle of the feed tray? Replace the paper in the middle of the feed tray, and set the pa- per guides correctly. P.13 Are the paper guides cor- rectly set to the width of paper? Take out the papers on the feed tray, then jog and put them back. Then set the paper guides again. P.13

Remove paper from infeed area. Status: Solution: Paper jam or paper remains in the infeed area Remove the jammed paper in the infeed area and then press the STOP key or CLEAR/RETURN key to clear the error message. (→P.57 “How to Remove Jammed Paper from Infeed Area”) Remove paper from cut area. Status: Solution: Paper jam in the cut area, or incorrect paper size Remove the jammed paper in the cut area and then press the STOP key or CLEAR/RETURN key to clear the error message. Check paper size and set it again. (→P.58 “How to Remove Jammed Paper from Center Area or Cutter Unit”) Load paper. Status: Solution: No paper on the feed tray Load paper on the feed tray and then press the STOP key or CLEAR/RETURN key to clear the error message. J1:Feed error Check infeed area. Status: Solution: Paper jam in the infeed area Remove the jammed paper in the infeed area and then press the STOP key or CLEAR/RETURN key to clear the error message. (→P.57 “How to Remove Jammed Paper from Infeed Area”) J2:JAM in CNV area Check center area. Status: Solution: Paper jam in the conveyor area Remove the jammed paper in the conveyor area and then press the STOP key or CLEAR/RETURN key to clear the error message. J3:JAM in cut area Remove paper from cut area. Status: Solution: Paper jam in the cur area, or incorrect paper size Remove the jammed paper in the cut area and then press the STOP key or CLEAR/RETURN key to clear the error message. Check paper size and set it again. (→P.58 “How to Remove Jammed Paper from Center Area or Cutter Unit”) J4:Double feed Check infeed area. Status: Solution: Two or more sheets of paper are fed at once in the infeed area. Remove the jammed paper in the infeed area and then press the STOP key or CLEAR/RETURN key to clear the error message. If the error often occurs, contact our service personnel. (→P.57 “How to Remove Jammed Paper from Infeed Area”) When Messages Appear Error messages appear on the LCD panel when the machine does not operate even when the START key is pressed. Take corrective actions below and then press the STOP key. The standby screen will appear and the machine will be ready for operation.

Error Message Status and Solution E1:CTR MTR Locked Check cutter area. Status: Solution: The cutter is locked due to a paper jam. Solution: Remove the jammed paper in the cutter area and then press the STOP key or CLEAR/RETURN key to clear the error message. Use paper of specifi ed thickness. (→P.58 “How to Remove Jammed Paper from Center Area or Cutter Unit”) Top cover is open. Status: Solution: The top cover is open. Close the top cover. E2:Read error Contact service personnel. Status: Solution: Memory error Make a note of Error Code (E2:Read error). Turn off the power once, and then turn it on again. If the problem still persists, turn off the power and contact our service personnel. E3:Write error Contact service personnel. Status: Solution: Memory error Make a note of Error Code (E3:Write error). Turn off the power once, and then turn it on again. If the problem still persists, turn off the power and contact our service personnel. E4:Time-out error Contact service personnel. Status: Solution: Memory error Make a note of Error Code (E4:Time-out error). Turn off the power once, and then turn it on again. If the problem still persists, turn off the power and contact our service personnel. Raise paper set lever. Status: Solution: The START key or TEST key is pressed with the paper set lever lowered. Raise the paper set lever. (→ P.14) Paper is out of specifi cation. Status: Solution: Thickness and/or length of paper are/is out of specifi cation. Load paper of specifi ed thickness and length and then press the STOP key. (→P.8 “Acceptable Paper”) Rear cover is open. Status: Solution: The rear cover is not attached. Attach the rear cover.

How to Remove Jammed Paper from Infeed Area • Make sure that the power plug is disconnected from the outlet before putting your hand close to any moving part to remove jammed paper. Turn off the power switch and remove the power plug from the outlet. Open the top cover. U80251 Remove the jammed paper in the direction as shown in the fi gure. Insert the power plug into the outlet and turn on the power switch. Close the top cover. Press the STOP key. The JAM message disappears and the machine is now ready for operation. WARNING Jammed paper Top cover

If the jammed paper cannot be removed by the procedure described in step . 1. Turn off the power switch, and remove the power plug from the outlet. 2. Open the top cover. 3. Loosen the thumbscrews on the paper retaining plates, move the plates to each side, and then remove the jammed paper. * If a center slitter unit (optional) or perforator (standard/micro) unit (optional) is installed, loosen the thumbscrews and move the paper retaining plates to each side. Using the JOG REVERSE key and JOG FORWARD key to remove jammed paper 1. Remove the paper by pressing the JOG REVERSE key to move it backward and the JOG FORWARD key to move it forward. * Using these keys may however make the paper jam worse. Watch the condition of the jammed paper as you operate the keys. How to Remove Jammed Paper from Center Area or Cutter Unit • Make sure that the power plug is disconnected from the outlet before putting your hands close to any moving part to remove jammed paper. • Never put your hands inside the cutter unit or slitter unit (optional). These units contain dangerous cutting edges. • To remove jammed paper, use the tweezers supplied with the machine or an equivalent. U80254 JOG START STOP U80252 U80253 WARNING Jammed paper Top cover Thumbscrews

Troubleshooting U80256 U80255 4. If paper is jammed in the cutter unit, remove the two thumbscrews on the rear cover to remove the cover. 5. Remove the jammed paper. If paper is jammed in the cutter unit, use the tweezers supplied to remove the paper. (The colored part in the right fi gure is a cutter unit.) 6. Attach the rear cover. 7. Insert the power plug into the outlet and turn on the power switch. 8. Press the STOP key. The JAM message disappears, and the machine is now ready for operation. Thumbscrews Rear cover Cutter unit

Daily Maintenance .......................................................................... 62

and unplug the power cord. Otherwise, fi re or electric shock may occur. ● Never remove covers on the machine or modify them. ● Do not spill water or any liquid inside of the machine. It may cause fi re or electric shock. If it happens, contact our service personnel. Clean the exterior in the following procedures. 1. Tightly wring a soft cloth that has been moistened with water or mild detergent. 2. Wipe the exterior. 3. Wipe off the excess moisture on the exterior with a dry soft cloth. ● Never use alcohol or solvent cleaner. It may tarnish or damage the exterior fi nish. ● Do not put diluted petroleum or insecticide. It may cause fi re. WARNING Dust accumulation may cause the machine to malfunction. Clean it periodically. Contact our service personnel as for cleaning of inside of the machine. Clean the machine periodically to maintain its performance. Clean the sensor under the rubber rollers according to the following procedure. 1. Open the top cover. 2. Spray commercially available spray on the sensor or gently clean the sensor with a cotton bud to remove paper dust.

Specifi cations ................................................................................ 64

Type Tabletop type cut sheet cutter Paper size Length: 110 - 420 mm (4.334 - 17 inches) Width: 106 - 364 mm (4.1764 - 14.3416 inches) Paper weight 58 - 157 gsm (50 - 135 kg), 1 part/single sheet Minimum cut size (Length) 55 mm (2.166 inches) (0.1 - 17.0 mm: can be cut using memory cut stored except rear end of the paper.) Maximum cut size (Length) 210 mm (8.267 inches) (210.0 - 419.9 mm: can be cut using memory cut stored) Cutting method Guillotine cutter Feeding method Rubber rollers Feeding pressure adjustment (3 steps) * Feed support guide * Curl stopper roller Load capacity 45 mm 500 sheets (55 kg/64 gsm, bond paper) Cut accuracy +/- 0.5 mm * Not including last piece * May not be guaranteed depending on operating conditions and paper conditions. Cut size A3 (2, 3, 4, 5, 6, 7 cut) A4 (2,3, 4, 5) A4R (2, 3) A5 (2, 3) A5R (2) B4 (2, 3, 4, 5, 6) B4R (2, 3, 4) B5 (2, 3, 4) B5R (2, 3) 14" (2, 3,4, 5, 6) 11" (2, 3, 4, 5) 8.5" (2, 3, 4) Process speed Approx. 2,640 sheets/h (A4 3 cut, high-speed, no-slitter) Approx. 2,280 sheets/h (A4 3 cut, middle-speed, no-slitter) Approx. 1,260 sheets/h (A4 3 cut, low-speed, no-slitter) * Varies depending on slitter (with/without). * Number of processed sheets varies depending on paper conditions. Stacker Dropping stacker Stacker capacity Installed on the lower side: 75 mm, 800 sheets (55 kg/64 gsm) Installed on the upper side: 35 mm, 400 sheets (55 kg/64 gsm) Memory cut storage Up to 100 types Memory cut paper size Length: 110 - 420 mm, Width: 106 - 364 mm Memory cut limit 17.1 - 54.9 mm: Cannot be cut. Display 144x32 dots LCD with backlight

Other features Interlock safety cover (top cover / rear cover) Sheet counter (0 - 9999 sheets) Cutter counter (0 - 9999 cuts) Preset counter (0 - 999 sheets) JOB display (ON/OFF) Slitter checking mode Auto select of fi nishing process (Standard, Straight conveyor) Auto power off (OFF, 5, 15, 30, 60 min) Cut position adjustment (-15.0 mm - 0 - +15.0 mm) Process speed (3 steps) Proof feed Automatic cut up function (including the following conditions) * Finished cut accuracy: +/-0.7 mm * May not be guaranteed depending on use condition and paper conditions. Detections Cover (top cover / rear cover) Paper empty Paper feed lever Paper feed error Double feed (3 steps) * May not be detected depending on print darkness and print pattern. Paper conveyance error Cutter lock Optional equipment Center slitter unit Gutter guide Perforator (Standard/Micro) unit Attachment kit Straight conveyor Cabinet Dimensions In use: 795mm(W) × 575mm(D) × 250mm(H) Folded: 600mm(W) × 575mm(D) × 280mm(H) Weight 32 kg Power supply 100-230 V, 50/60 Hz, 0.5 - 0.3 A Power consumption (100 V, 115 V, 230 V) Standby: 13.2 W, 13.0 W, 13.0 W In operation: 39.6 W, 39.2 W, 38.8 W (No options attached) In operation: 34.6 W, 34.5 W, 34.0 W (with straight conveyor) Operating temperature 10 - 30 degrees C Operating humidity 40 - 70% (no condensing) Specifi cations are subject to change without prior notice.