Rev-A-Shelf 5243 Instruction Sheet

Text of Rev-A-Shelf 5243 Instruction Sheet

INSTRUCCIONES DE INSTALACIÓN

DES INSTRUCTIONS D’INSTALLATION TOOLS REQUIRED: OUTILS NÉCESSAIRES: HERRAMIENTAS NECESARIAS: ESTIMATED ASSEMBLY TIME: TEMPS ESTIMÉ DU MONTAGE: ESTIMAR EL TIEMPO DE MONTAJE: MIN CARE AND MAINTENANCE: ENTRETIEN ET MAINTENANCE: CUIDADO Y MANTENIMIENTO: Clean with a damp cloth and wipe parts dry. Limpie con un trapo húmedo y seque. Nettoyer avec un chif on humide et essuyer pour sécher complètement. ” I-

Component Check List • Lista para verifi car los componentes • Liste de vérifi cation des composants

Description • Descripción • Description 5243/5250 5258 5273 A Steel Frame • Marco de metal • Cadre en acier 1 1 1 B Top Slide • Glisser superior • Coulisse du haut 1 1 1 C Bottom Slide • Deslizar inferior • Coulisse du bas 1 1 1 D T Type Door Bracket • Soporte de puerta tipo T • Support de type T pour porte 2 2 2 E Door Brack

FACE FRAME CABINETS

Install bottom slide 1) Attach feet (#9) to bottom slide (C) using M4 screw (#8) as shown in f gure 1. To attach the rear foot, the soft-close will need to be removed f rst as shown, then re-attached afterwards. You will need to remove the inner member(s) from the slide so you have a hollow channel when attaching the feet. Install top slide 3) The top slide (B) of the pantry needs to be mounted f ush with the face frame. It will likel

[108]mm 4” [102mm]

N/A N/A 5750 [108]mm 4” [102mm] [530]mm N/A 5758 [108]mm 4” [102mm] N/A N/A 5773 [108]mm 4” [102mm] N/A N/A Door Mounting 9) The top and bottom of the pantry use the T type door mount brackets (D). Remove center screw as shown in f gure 8, insert bracket and then connect the bracket to the top of the frame with center screw. Tighten this screw and f nal door adjustments will be made later. 10

15) The f rst adjustment is the left to right tilt. By tightening the

front screw and loosening the back screw, the door will tilt out on the left. The reverse is true if you loosen the front screw and tighten the back screw, the door will tilt out on the right. Once you get this tilt adjustment correct, tighten the center screw both top and bottom. Now snap on the logo cap (#4) to cover this hardware on the top. See f gure 13. 16) The next a

GABINETES SIN MARCOS • ARMOIRES AVEC CADRAGE AVANT

Instale el deslizante inferior • Installer la coulisse du bas 1) Sujete la pata (#9) a la parte inferior del deslizante (#C), utilizando un tornillo M4 (#8) como se muestra en la f gura número 1. Para sujetar la pata trasera, primero el sistema de cerrado suave debe ser removido, luego deberá reajustarse nuevamente. Usted necesitará remover el miembro(s) interior del deslizante para que tenga un can

Cadrage Avant Sans Cadre

C D 5743 [108]mm 4” [102mm] N/A N/A 5750 [108]mm 4” [102mm] [530]mm N/A 5758 [108]mm 4” [102mm] N/A N/A 5773 [108]mm 4” [102mm] N/A N/A Montaje de la Puerta • Montage de la Porte 9) La parte superior e inferior de la alacena, utiliza el soporte de montaje para puerta tipo T (D). Quite el tornillo central, como se muestra en la f gura 8, inserte el soporte y luego conecte el soporte a la parte

Rev-A-Shelf Indoor Furnishing Owners Instructions: