KI Uniframe Convertible Bench Assembly Instructions Manual

Assembly Instructions Main Horizontal Tube Qty. 1 Item #1 Steel Spacer, .50” OD x .38” ID Qty. 6 Item #2 Nut, / -20 Nylon Lock Qty. 4 1 4 Item #3 Nut, / -16 Nylon Lock Qty. 4 3 8 Item #4 Nut, / -14 Center Lock Qty. 4 7 16 Item #5 Nut, / -16 UNC Acorn Qty. 2 3 8 Item #6 Flat Washer, / ” SAE Qty. 4 1 4 Item #7 Flat Washer, / ” SAE Qty. 12 3 8 Item #8 Flat Washer, ½” Nylon Qty. 4 Item #9 Hex Bolt, / -16 x 2 / ” HHCS Qty. 2 3 1 8 8 Support Leg Assembly Left-hand Qty. 1 Support Leg Assembly Right-hand Qty. 1 Tools Required: 4mm Hex wrench, / ”ratchet wrench, / ” & / ” sockets, adjustable wrench. 3 7 9 8 16 16 Bench Assembly Qty. 1 Top Assembly Qty. 1 Label on leg L=Left- & R=Right-hand Leg Assemblies Item #10 Socket Cap Screw, / -20 x 2” Button Head Qty. 4 1 4

Assembly Instructions 1. Identify right- & left-hand support leg assemblies by labels on upper support member (Figure 1 & Detail A). 2. Insert main horizontal tube through the pivot brackets in each bench assembly (Figure 1). 3. Insert four 1/4 -20 x 2” screws (item 10) into main horizontal tube (Figure 1). 4. Place bench assembly with main tube onto leg saddles. 5. Align item 9 screws with holes and attach bench assembly with 1/4” flat washers (item 6) and 1/4 -20 nylon lock nuts (item 2) (Figure 2 & Detail B). Label on leg L=Left- & R=Right-hand Leg Assemblies left leg right leg pivot bracket pivot bracket main horizontal tube pivot bracket leg saddle item 6 item 2 item 10 item 10 Detail A Detail B 1. Identify right- & left-hand support leg assemblies by labels on upper support member (Figure 1 & Detail A). 2. Insert main horizontal tube through the pivot brackets in each bench assembly (Figure 1). 3. Insert four 1/4-20 x 2” screws (item 10) into main horizontal tube (Figure 1). 5. Align item 9 screws with holes and attach bench assembly with 1/4” washers (item 6) and 1/4-20 nylon lock nuts (item 2). 4. Place bench assembly with main tube onto leg saddles. Item Description 2 Nut, / -20 Nylon Lock 1 4 10 Screw, / -20 x 2” Button Head Cap 1 4 6 Flat Washer, / ” SAE 1 4 Figure 1- Assemble Bench to Legs

Assembly Instructions 1. Install leg braces to bench legs using hardware installed in sequence shown (Figure 2 & Detail B). 2. At top of leg uprights, install 3/8” flat washer (item 7), 1/2” nylon washer (item 8) and 3/8” steel spacer (item 1) onto leg bolts in sequence shown (Detail C). 3. Locate “L” and “R” labels on apron assembly under top. 4. Install top assembly through slotted angle over the spacers on bolts (Detail C). 5. Install 1/2” nylon washer (item 8), 3/8” flat washer (item 7) and 3/8-16 nylon lock nut (item 3) onto bolts and tighten (Detail C). match labels slotted angle top assembly apron assembly label “R” leg upright label “R” bench leg leg brace Detail C Detail B Bench Legs to Bench Brace *Steel spacers allow the fasteners to tighten without restricting movement at pivot points * Install items 7, 8 & 1 hardware on both legs before installing top assembly item 3 item 7 item 8 item 9 item 4 item 7 item 1* item 7 item 5 item 1* item 8* item 7* 1 Steel Spacer, .50” OD x .38” ID Item Description 3 Nut, / -16 Nylon Lock 3 8 4 Nut, / -14 Center Lock 7 16 7 Flat Washer, / ” SAE 3 8 8 Flat Washer, ½” Nylon 9 Hex Bolt, / -16 x 2 / ” HHCS 3 1 8 8 5 Nut, / -16 UNC Acorn 3 8 Figure 2 - Braces to Top, Legs & Bench Assembly

Assembly Instructions 1. Attach 3/8” flat washer (item 7) and steel spacer (item 1) onto both apron bolts in sequence shown (Figure 3 & Detail D). 2. Rotate top assembly up (Figure 3). 3. Rotate both top support brackets up and locate them onto the apron bolts. Spacers go into the brace hole (Figure 3 & Detail D). 4. Install 3/8” flat washer (item 7) and 3/8-16 nylon lock nut (item 3) onto apron bolts and tighten (Detail D). Note: Steel spacers allow the fasteners to tighten without restricting movement at pivot points. Note: If the top surface assembly is not level once the top support brace is attached to the apron bolt, adjustments can be made at both ends of the top surface. The “apron bolt” is secured at the factory into a slotted hole in the “locking pivot angle brace” and this slot allows up to 5/8” of adjustment. 5. To adjust the apron bolt on the locking pivot angle brace, first loosen the outermost top nut holding the top support brace to the apron bolt (if installed already in step 4). Next loosen the nut between the top support brace and the locking pivot angle brace by using two 9/16” wrenches, one between the braces and one on the bolt head. Adjust the table to level, then re-tighten the nut and the bolt head which pinch the locking pivot angle brace only. Repeat procedure at other end of bench as necessary (Figure 3 & detail inset). Detail D Top Leg Brace to Apron *Steel spacers allow the fasteners to tighten without restricting movement at pivot points Detail E Leveling Surface item 7 item 1* item 7 item 3 Figure 3 - Braces to Top at Apron Assembly top assembly apron bolt apron bolt top support brace top support brace Item Description 1 Steel Spacer, .50” OD x .38” ID 3 Nut, / -16 Nylon Lock 3 8 7 Flat Washer, / ” SAE 3 8 apron bolt locking pivot angle brace 3/ -16 nut 8 (center) 3/ -16 nut 8 (outermost)

P.O. Box 8100 Green Bay, Wisconsin 54308-8100 1-800-424-2432 www.ki.com KI is a registered trademark of Krueger International, Inc. © 2019 Krueger International, Inc. All Rights Reserved Code KI-61586R12/KI/PDF/0719 Part # 13.7709