ItsImagical ECO AIR ENGINE CAR Manual 

Mechanical Parts List Tapping Screw Tapping Screw Round Shaft Round Shaft 1 20 QTY 6 QTY QTY 1 QTY P1 P2 P3 P4 Diagonal Cutter Scissors Screwdriver Gasoline is currently the fuel of choice, but petroleum used to make it is becoming increasingly difficult to find and is contributing to en ...

Hex Shaft (Long) Round Shaft P8 P9 P10 P5 P6 P7 2 QTY 1 QTY 1 QTY PET Bottle Oil Bag Bottle Top Red Cap (Medium) Red Cap (Big) Spacer Spring O-ring (Black) Red Cap (Small) 1 QTY P16 Silicon Tube Sticker Do not touch the oil while fitting the silicon tube. (Spare part : 1 pc) (Spare part : 1 pc) Spare parts Ignore Ignore ...

How To Fit Air Tube Tilt the tube Tube 1 2 Measuring & Marking Cutting How To Cut Air Tube P15 Follow the steps above, cut the air tubes when they are required. Do not cut them in advance. ...

Do not cut them in advance. C 1 2 3 4 5 MADE IN TAIWAN 6 1 2 3 4 5 7 6 8 9 10 20 19 18 17 16 15 14 13 12 11 D MADE IN TAIWAN Ignore 1 2 2 4 3 4 5 A MADE IN TAIWAN 1 6 OIL B7 B 8 10 9 9 3 2 4 5 13 10 12 11 MADE IN TAIWAN 14 MADE IN TAIWAN 1 2 3 3 3 E Ignore ...

1 2 11.5 cm 7 A1 11.5cm 11.5cm 2 1 14 cm 1:1 Scale 1:1 Scale Prepare air tube before assembly. Prepare air tube before assembly. 14cm ...

B8 9 6 Tissue Paper P16 B8 B7 Note : Oil the parts when appears. Do not oil outside the shadow as shown below. Example: Do not spill any oil from the B7 oil sink. Keep oil contained. Apply Oil ...

assemble below steps smoothly. https://youtu.be/mmzSFocksso Make sure P10 is placed in the proper direction to avoid air leakage. 10 9 10 D12 D20 Push & pull the oiled part D16 several times to make it work smoothly. 2 1 8 ...

steps smoothly. Video Tips P17 B14 P17 12 E2 P9 O-ring (Black) P9 O-ring (Black) B14 A3 E2 1 2 3 C5 Use C5 to assist you in setting P9 to E2 entirely. 2 1 P4 5 6 Valve Assembly Ensure the direction of two P17 to avoid air leakage. Use B14 to assist you in setting two P9 entirely. 1 Push P17 to the bottom (as per Fig ) and make P9 to set flatly. 1 Push P17 to the top (as ...

both ends of the spring to make sure of good strength & extension before assembly. ...

https://youtu.be/Jgh963Gc2i0 Air Leakage Testing – The Valve 13 1 2 P12 Red Cap (Big) D4 D4 1 Seal the hole of the boss side with a finger. 2 Push in the D4. P17 Make sure that both P17 move to the direction indicated by the arrows when the D4 is pushed in. Make sure that both P17 move in the direction indicated by the arrows when the D4 is pulled back. Confirm that the D4 cannot ...

Air leakage testing – Tube Module B Fold the tube. Insert the folded tube to the hole. 1 Seal the hole of the concave side with a finger. 2 Pull the D4 back. 1 2 E2 Install E2 at a right position as shown above. Confirm that pulling the D4 back is hard, or you need more power to pull the D4 back. ...

Pointer turns to above position 15 Air Leakage Working Functionally Hold A3 firmly! Repeat a “ Push & Pull” movement using D4 15~20 times to collect air into PET bottle. Check pressure meter and examine the position that the pointer swings to. Results shown below will reveal if tube module B is installed functionally or experiencing air leakage. ...

Position 2: Back to page10, and re-install steps 7~13 again. Position 3: Back to page12, and re-install steps 1~6 again. Check following positions if air leakage was occurred, and re-install as below: Position 1: Position 2: Position 3: 2 1 D4 Be sure to remove air tube & D4 from A3 after testing is finished. 16 Put D4 aside B7 to avoid oil spilling with others. ...

Insert P6 hex shaft to the bottom as indicated on the right fig. ( scale 1:1 ) Make sure parts D2/D5 are at opposite positions. ...