Finelite HP-2 Installation Instructions

local/national codes by a Certified Electrician. Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com 1 © 2016 FINELITE, INC. ALL RIGHTS RESERVED. Form 98240 V2. 11/16 Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S HP-2 Recessed T-Bar Mitered Corner Installation Instructions Conduit Plate (provided) #8-18 x 1/4" Screws (provided) Conduit (by others) Jam Nut (by others) Wiring Connections Starter Step 2 Install starter luminaire on to T-Bar. T-Bar Bracket (provided) Starter #8-18 x 1/4" Screws (4) (provided) Tie-wire (by others) Step 3 Attach T-Bar bracket (provided) to luminaire with #8-18 x 1/4" screw (provided). Secure luminaire to structure using tie-wire (by others), as per code. Step 4 Remove conduit plate then install wiring through conduit plate and through jam nut. Secure jam nut onto conduit. Make wiring connections and then reinstall conduit plate. Diffuser Starter Step 1 Remove diffuser and set aside to prevent it from getting dirty or damaged. 0 - 10V Dimming Scan QR code for helpful video(s) Wires Splice Box Door Jam Nut Conduit Wires Splice box door Open optional splice box door to access wiring. Run power cable through knock-out. Make electrical connections. Secure conduit on to splice box with jam nut and close splice box door. OPTIONAL SPLICE BOX

local/national codes by a Certified Electrician. Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com 2 © 2016 FINELITE, INC. ALL RIGHTS RESERVED. Form 98240 V2. 11/16 Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S HP-2 Recessed T-Bar Mitered Corner Installation Instructions Back Plate Joiner/Ender Starter Elbow Sleeves Joiner/Ender Starter Channels Step 7 Align elbow sleeves with channels in body. Slide joiner/ender onto starter. Remove back plate clips (provided) from back plates at corner joint. Starter Joiner/Ender Step 6 Slide joiner/ender luminaire onto T-Bar. Starter Joiner/Ender Double Diffuser (pre-installed) Step 8 Step 9 Slowly swing down back plates. CAUTION: Do not twist back plate when swinging down - it will come out of the support extrusion. Note that the screw shown is the pivot point and the back plate can be slid a few inches either way for ease of access to the driver space. IMPORTANT STEP: Secure joint with two yoke brackets (provided) using #10-32 x 5/8" screws (provided). CAUTION: When installed correctly these brackets will pull luminaires together to make a tight joint. Do not over-tighten. #10-32 x 5/8" Screws (provided) Yoke Brackets (provided) Starter Joiner/Ender Step 10 Back Plate Clip Pivot Point Joiner/Ender Diffuser Step 5 Remove diffuser from joiner/ender luminaire and set aside to prevent it from getting dirty or damaged. IMPORTANT STEP

local/national codes by a Certified Electrician. Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com 3 © 2016 FINELITE, INC. ALL RIGHTS RESERVED. Form 98240 V2. 11/16 Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S HP-2 Recessed T-Bar Mitered Corner Installation Instructions Diffuser Diffuser Starter T-Bar Bracket Joiner/Ender #8-18 x 1/4" Screws (4) (provided) #6-20 x 1/2" Self Drilling Screws (4) (provided) Secure To Structure (by others) Step 12 Step 13 Attach T-Bar bracket (provided) onto joiner/ender with #8-18 x 1/4" screws (provided). Secure joiner/ender to structure using tie-wire (by others), as per code. Secure all luminaires to the T-Bar by driving #6-20 x 1/2" self drilling screws (provided) through the T-Bar brackets (provided) into the T-Bar. Reinstall diffusers and turn power on to luminaires. Plug-Together Wiring Back Plate Double Diffuser (pre-installed) Starter Joiner/Ender Connect plug-together wiring. Close all back plates by pushing them back in their original position and pushing the clips back in. Step 11 Back Plate Clip