Eaton Linear Tech Bench 1 Installation Manual

Text of Eaton Linear Tech Bench 1 Installation Manual

Sit-to-Stand Techbench installation manual

Sit-to-Stand Techbench Linear Tech Bench 1 Corner Tech Bench 1

SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench

Sit-to-Stand Techbench Installation Manual 2 Table of contents - I.  GENERAL INFORMATION About this guide .�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.2 Contact information.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.�.2 Before you begin.�.�.�.�.�.�.�.

Eaton Linear Tech Bench 1 SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench

Sit-to-Stand Techbench Installation Manual • Read and understand the instruction herein before attempting to unpack, assemble, operate or service the Sit-to-stand bench. • Follow all information that is found on safety labels on the product and packaging. • Familiarize yourself with the various bench components described within this manual. • The use of personal protect
SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench Important safety instructions DANGER Read all instructions before assembling and using this furnishing - Save these instructions This bench has an electrically driven adjustable worksurface. In its lowest position, the worksurface is very close to the support base structure. The bench’s lift motors have sensors that will detect an obstructi
SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench Sit-to-Stand Techbench Installation Manual SECTION II - Preparing to assemble the bench Sit-to-Stand Corner and Linear Techbench Components Tools required General assembly • Cordless screw gun (recommended) • Magnetic driver bit holder • 3/8" driver bit • 3/4" open end box wrench • #2 Phillips bit • #3 Phillips bit • Level • 4mm Hex wrench (provided in hardware k
SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench A 1/4" x ½" hex head self- threading screw Eaton part # 54538 B M6 x 14mm Allen head screws Eaton part # 105948 C M6 x 6mm Shoulder screw Eaton part # 107239 D 6mm id nylon washer Eaton part # 107238 E 6mm id steel washer Eaton part # AN960C-416 F M8 x 12mm Phillip’s pan head screw Eaton part # 97409 G 8mm id Lock washer Eaton part
SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench Sit-to-Stand Techbench Installation Manual A. Wiring the bench - AC cord WARNING USE CAUTION WHEN LIFTING WORK SURFACE. TWO PEOPLE ARE REQUIRED TO AVOID INJURY. • Lay work surface flat on floor with work surface stiffeners face up. • Plug in ac cord to lift motor controller and route wire on bottom of controller as shown to create strain relief. • Assemble Lift Motor Contr
SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench SECTION III - Assembling the corner and linear bench L x 1 H x 2 B. Wiring the bench - control pad • Route control pad wire in slot in work surface. Then out thru bottom slot of work surface stiffener and to side slot in the stiffener. • Plug RJ45 connector into lift motor controller. • Assemble control pad to work surface using #8
SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench Sit-to-Stand Techbench Installation Manual C. Wiring the bench – motor cables • Route motor cables #1, #2, #3 & #4 as shown. Connect each cable to Lift motor controller as shown, an auditable click will be heard when the connection is made. • Cables in work surface stiffener are to be routed as shown using cable retainer hardware N. Cable retainer uses existing work surface
SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench D. Wiring the leg assembly • Position Both left and right leg assemblies in work surface stiffeners-position lift motors about 1" from there mounting position as shown. • Connect each lift motor cables to the respective lift motor. A click is audible when the connection is made. • Remove cable from wire stay as required. WARNING
SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench Sit-to-Stand Techbench Installation Manual E. Leg assembly and back panel • On one end of back panel, align back panel holes with back panel mounting holes in leg assembly. Hand thread (1)1/4-20 x ¾" lg hex head screw hardware M. • Slide opposite leg assembly towards back panel and align holes in panel with mounting holes in leg assembly. Hand thread (3) ¼-20 x ¾" lg. hex
SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench Work surface stiffener - slot Work surface stiffener Work surface stiffener - hole 6mm id nylon washer hardware D M6 shoulder screw hardware C M6 x 14mm Allen screw hardware B 6mm id steel washer hardware E Lift motor F. Leg assembly • With 6mm id steel washer, hardware E and M6 x 14mm Allen head screw, hardware B, thread (8x) thru work
SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench Sit-to-Stand Techbench Installation Manual G. Initialize the lift motor system WARNING UNPLUG BEFORE ENERGIZING OR OPERATING THE LIFT SYSTEM • MAKE SURE THAT THE PRECEDING ASSEMBLY STEPS HAVE BEEN FOLLOWED AND ARE COMPLETED. • VERIFY THE CORRECT POSITION OF ALL LIFT MOTOR CONNECTORS. VERIFY THAT ALL LIFT MOTOR CABLES ARE PROPERLY SEATED IN THEIR RECEPTACLES. • MAKE SURE THAT
SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench A. Adjusting the levelers • Level the bench. Using bubble level, adjust the four levelers as required to achieve both front to back and side to side level. Adjust using ¾” box wrench on check nut. Leveler ¾" across flat check nut SECTION IV - Setting up and using the bench Page 15 of 44 Description The DP1CS is equipped with display
SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench Sit-to-Stand Techbench Installation Manual SECTION V - Corner and linear accessories A. Full shelf installation • Lay bench on side. Align foot mounting holes with full shelf holes. Assemble full shelf using (8) ¼-20 x1/2" lg hex head shelf taping screws. WARNING USE CAUTION WHEN LIFTING WORK SURFACE. TWO PEOPLE ARE REQUIRED TO AVOID INJURY. A x 8 Hardware required Full shelf Cu
SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench SECTION V - Corner and linear accessories B. Half shelf installation • Using (4) ¼-20 x ½" lg hex head self-tap screws, assemble left and right shelf bracket to half shelf. Screws are to be assembled thru holes in bottom of half shelf into left and right-side brackets. • Assemble left and right-side brackets to frame rails. Hand th
SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench Sit-to-Stand Techbench Installation Manual SECTION V - Corner and linear accessories M x 4 Hardware required C. Caster and foot rest installation • The casters replace the installed Levelers. Tip the bench on its back, exposing the (4) levelers. • Remove the leveler and check nut on each foot. • To assemble caster, align (4) mounting holes in bottom of foot with slots in
SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench SECTION V - Corner and linear accessories P x 4 K x 2 Hardware required D. Cable chain installation • The cable chain can be mounted from either left or right side of the back of the work surface – near the cable grommets. • Determine which side that the cable chain will be assembled. • Assemble chain bracket with (2) 10-32x1/2
SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench Sit-to-Stand Techbench Installation Manual SECTION V - Corner and linear accessories E. Flextray installation • The flextray lengths vary along with the number of flextray brackets. • To assemble the flextray, mount the flextray brackets to the back panel first. • Assemble the flextray bracket to back panel with (2) 3/8 x 1-1/4" lg hex head self-tap screws. The number of
SIT-TO-STAND TECHBENCH INSTALLATION MANUAL Eaton.com/techbench F. Ganging plate • Pre-assemble (2) ¼-20 x ½" lg. hex head self-tap screws into the left foot of one bench and (2) ¼-20 x ½" lg. hex head self- tap screws into the right foot of the adjacent bench. Thread each screw only half way. • Move and align both benches about 8" • Assemble ganging plate the benches by sliding over pre

Eaton Indoor Furnishing Owners Instructions: