Advantech IPC-610 Operation & User’s Manual

Copyright Notice This document is copyrighted, September 1998, by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this ...

iii Table of Contents Chapter 1 General Information...................................................................................................1 1.1 Introduction ............................................................................................................................................... 1 1.2 Specifications....................................................................................................... ...

1 Chapter 1 General Information 1.1 Introduction The IPC-610 is a PC/AT-compatible computer designed for industrial applications. This rugged, all-steel chassis meets the EIA RS-310C 19" rackmount standard. The unit includes a 14-slot PC-bus compatible passive backplane, and a more efficient switching power supply in a single fan-cooled chassis. The passive backplane configuration of the IPC-610 minimizes downtime, simplifies troubl ...

Environmental Specifications • Operating temperature: 0 ~ 50° C (32 ~ 122° F) • Relative humidity: 10 ~ 95% @ 40° C, non-condensing • Vibration (operating): 5 ~ 17 Hz, 0.1" double amplitude displacement; 17 ~ 500 Hz, 1.5 g acceleration peak to peak • Shock (operating): 10 g acceleration peak (11 ms duration) • Safety: C-UL approved • EMI: Meets FCC/VDE Class A • CE compliant 1.3 Dimensions Figure 1-1: IPC-610 dim ...

3 Chapter 2 System Setup Setting up your IPC-610 requires only a screwdriver and a small amount of time. Before you begin, you should also gather together all of the cards you plan to install, as well as the keyboard you plan to use. A lockable door is located on the chassis front cover, providing access to the control panel. This offers protection and security against damage and unauthorized access. The control panel functions incl ...

2.3 The Hold-down Clamp The IPC-610 uses a hold-down clamp to ensure the plug-in cards are securely fastened. It also offers protection against shock and vibration. To install your cards into the passive backplane, proceed as follows: 1. Detach the hold-down clamp by removing the two screws located at each end and lifting it off the chassis. (See Fig. 2-4) 2. Insert the rubber buffers (provided) into the hold-down clamp. These bu ...

5 Figure 2-8: Replacing the filter 2.5 Replacing the Filter The filter is located next to the lockable door. Under continuous use, the filter should be removed about once a month. To replace the filter, refer to Fig. 2-8 below and do the following: 1. Open the lockable door. 2. Remove the filter out by gently pulling the tab and sliding the filter to the right. 3. Slide a new filter in until it snaps into place. 4. Close and lock th ...

Figure A-2: IPC-610 with redundant power supply Figure A-1: IPC-610 with PS/2 size power supply Appendix A Rear Cover and Window A.1 Changing the Rear Cover According to Power Supply Used ...

7 A.2 The Backplane 1. Select the backplane you want to install, such as the PCA-6114, PCA-6114P4, PCA-6114P4R, PCA-6114P7, PCA-6114P10, etc. 2. To change the backplane's rear window, see Fig. A-3. Figure A-3: Rear window of IPC-610 for standard 14-slot backplane, with PS/2 size power supply ...

Figure A-4: Rear window of IPC-610 for standard AT motherboard A.3 AT Motherboard 1. Make sure that the motherboard supports AT power. 2. To change the rear window for standard AT motherboards, see Fig. A-4. ...

9 Figure A-5: IPC-610 ATX chassis component layout A.4 ATX Motherboard 1. Make sure that the motherboard supports ATX power. 2. To change the rear window for standard ATX motherboards, see Fig. A-5. ...

Figure B-1: IPC-610 exploded diagram (internal components) Appendix B Exploded Diagrams ...

13 Appendix C Safety Instructions Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User's Manual for later reference. 3 . Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or sprayed detergent for cleaning. Use a moist sheet or cloth for cleaning. 4. For pluggable equipment, the socket-outlet should be installed near the equipment and should be easily accessible. 5. Keep thi ...

Wichtige Sicherheishinweise 1. Bitte lesen sie Sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. 5. Das Gerät ist vor Feuc ...