Datum Storage 4Post Trakslider Assembly Instructions Manual

(MONDAY THRU FRIDAY 8 AM - 5 PM EST) 4Post Trakslider Instructions INST0083 REV2 WS 4/16/08 PAGE 1 OF 31 ...

(Required when not using Datum shelving) Power Drill Rubber Mallet Or Plastic Tip Hammer 4' Bubble Level NOTE These instructions apply to Datum 4Post Shelving with 4Post Adapter Brackets. If other brands are used, it will be necessary to drill holes to complete installation. Tools Required for Assembly PAGE 2 OF 31 ...

upright on left and an open "T" upright on right to hold uprights in position (see Figure A). Make sure that the uprights are positioned so that bent flanges are at the bottom of the unit as shown in Detail B. Rivets of shelf support fit into keyholes on uprights as shown in Figure A & Detail B. Use a rubber mallet or plastic tip hammer to tap shelf sup ...

for Stationary Shelving 15" 12" Depth of Shelving 18" Step 3: If required (See Table 1), install shelf reinforcements as shown in Figure C. Step 4: Install bottom shelf by tilting the shelf as shown if Figure D. Shelf should then lie flat on shelf supports. Figure D Figure E Step 5: Install back stop for bottom shelf. Count up three complete keyholes from top of shelf and ...

(if required) as previously shown, working from bottom to top. Keep in mind your installation may be different, as shelf spacing varies from job to job (See Figure F for typical configurations). Do not install components at the top of unit at this time; when complete the assembled unit should look similar to Figure G. Fourth Opening Typically Has Pos ...

in Figure J by placing rivets of the brackets into first two keyholes under the shelf support. Install rear standard shelf support for top panel by placing rivets of support into the top two keyholes of the uprights as shown in Figure H and Detail I. Step 7: Step 9: Install top cover front support channel by placing top rivet on each side of channel into the firs ...

cover lock brackets to uprights using #10-24 x 3/8" screws as shown in Figure L. Place top cover on unit as shown in Figure M. Unit should now look similar to Figure N. Step 11: Figure M Figure N #10-24 x 3/8" Phillips Pan Head Sheet Metal Screw #10-24 x 3/8" Screw Shelf Support Upright Top Cover Top Cover Front Support Channel Upright PAGE 7 OF 31 Top Cover Front Support Channel ...

units (Figure P), skip to Step 12b. If your section consists of two units only (Figure O), continue here with Step 12a. Step 12a: Position a closed 'L' upright to the right of assembled unit and install shelf supports and kick plate by repeating Steps 1 & 2 (Figure O). Go to Step 13. Repeat steps one and two as needed to set up all units in the section except for the end unit. For ...

systems only) and lock bracket knockouts on top cover of first unit (see Figure Q). Remove knockouts with phillips screwdriver and rubber mallet or plastic tip hammer. Step 13: 1/4-20 x 3/4" Hex Bolt 1/4-20 Flanged Hex Nut Figure S Use (3) 1/4-20 x 3/4 hex bolts and (3) 1/4-20 flanged hex nuts to attach top stablizer channel to top cover of first unit using the first set of holes ...

Moveable Shelving Section Stainless Steel Front Cap Shelf Reinforcement Decking Welded Rail End Stop End Cap Stationary Connector Channel Carriage Single Rivet Shelf Support Back Stop Divider Shelf Standard Shelf Support Closed 'T' Upright Standard Shelf Support Top Cover Front Support Channel Top Cover Rear Support Channel Tri-Slider Hat Channel Tri-Slider Stabilizer Bracket Top Cover Lock Bracket Safety Stop BiSlider Roller Bra ...

Step 15: Position a stationary connector channel in front of each stationary base unit. Attach each channel to the uprights of the stationary units using #8 tek screws as shown in Figure U and Detail V. Step 16: Install (12) leveling glides in each rail assembly making sure that each glide is screwed in completely and is flush with the bottom of the rail assembly (See Figure W). Stationary Units Stationary Con ...

Rail assemblies have corresponding slots which slide over connector channel to secure rail assembly into place (See Figure X and Detail Y). Step 18: Join rail assemblies together using (4) 1/4-20 x 3/4" hex bolts and (4) flanged hex nuts. Make sure rails are flush from one assembly to the next before tightening bolts (See Figure Z). -For BiSlider Systems, conti ...

Attach deck end cap to rail assemblies starting from left end of rail assembly. Use (4) 1/4-20 x 3/4" hex bolts and (4) 1/4-20 flanged hex nuts to secure end cap to rail assembly as shown in Figure AC. Repeat for right side of system. Skip to Step 24. Position additional row of rail assemblies in front of Bi-Slider rail assemblies that were already in place as shown in Figure AB. Join secon ...

of rail assembly. Use (6) 1/4-20 x 3/4" hex bolts and (6) 1/4-20 flanged hex nuts to secure end cap to rail assembly as shown in Figure AE. Repeat for right side of system. Step 23: For QuadSlider Systems Only Position (2) additional rows of rail assemblies in front of Bi-Slider rail assemblies that were already in place as shown in Figure AD. Join second & third rows of rai ...

assemblies and should be flush with the top of the rails when installed (See Figure AF). After decking is in place, install end stops at the end of each rail using (1) 1/4-20 x 1/2" cap screw (See Figure AF). Step 25: Step 24: LEVELING OF UNIT Determine highest point on rail assembly. Working out from this point, level rails by adjusting leveling glides. For system to fu ...

Tek Screw Fasten the shelving unit assembled in the previous step to a carriage using (4) #10 x 3/4" flat head tek screws (See Figure AK & Detail AL). Step 28: Note: Single rivet shelf supports are used only for the bottom shelf on units that will be attached to a carriage. Standard shelf supports are used for the rest of the unit. Temporarily mount a shelf support at chest height between (2) clo ...

shelf as shown in Figure AM. See Table 2 for proper number of reinforcements. Figure AN shows the visual difference of a standard shelf reinforcement compared to a heavy duty reinforcement. Step 30: Install bottom shelf by tilting as shown in Figure AO. It should then lie flat on shelf supports and reinforcement(s). 18" Depth of Shelving 12" 15" Table 2 - Shelf Re ...

complete keyholes from top of shelf and place rivets of back stop into these keyholes (See Figure AP). Step 32: Install (2) standard shelf supports at the correct locations based on unit configuration. See Figure F on Sheet 5 for guidance on shelf spacing. Step 33: If required (See Table 3) install standard shelf reinforcement(s) as shown in Figure AR. Two None Number ...

should then lie flat on shelf supports and reinforcement(s). Step 35: Install back stop for second shelf. Count up three complete keyholes from top of shelf and place rivets of back stop into these keyholes (See Figure AT). Step 36: Install remainder of shelf supports, shelves, back stops, & shelf reinforcements (if required), working from bottom to top. Keep ...

Head Sheet Metal Screw Figure AW Step 37: Place the rivets of the top cover rear support channel into the keyholes at the top of the upright at the rear of the unit. The top rivet on each side should be inserted into the first complete keyhole at the top of the uprights (See Figure AV). Tap channel into place with rubber mallet or hammer to seat rivets firmly into bottom of keyholes. Step 38: Use (2) #10-24 x 3/8" phill ...