WilTec 61870 Operation Manual

ARTICLE 61870 Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignificantly. Updating the documentation If you have suggestions for improvement or have found any irregularities please contact us. © by WilTec Wildanger Technik GmbH Seite 20 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de ...

document can be copied or duplicated in another form without the prior written consent of WilTec Wildanger Technik GmbH. The WilTec Wildanger Technik GmbH assumes no liability for any errors in this user manual or the connection diagram. Although WilTec Wildanger Technik GmbH has made every effort to make sure that this user manual is complete, accurate and updated, errors cannot always be avoided. In the event of problems with this user manual please complete and send this form back to us. FAX-notification (+++49 2403 55592-15), from: _______________ ...

o Before Start-Up  Tool: Impact Wrench o Figure o Intended use o Start-Up o Maintenance and Care  Tool: Chisel Hammer o Intended use o Start-Up o Chisel Replacement o Maintenance and Care  Tool: Ratchet Screwdriver o Figure o Intended use o Start-Up o Maintenance and Care  Tool: Rod Grinder o Intended use o Operating Instructions o Maintenance  Specifications  Explosion Drawing o Impact Wrench o Chisel Hammer o Ratchet Screwdriver o Rod Grinder © by WilTec Wildanger Technik GmbH Seite 22 http://www.WilTec.de http://www.aoyue.eu http://www. ...

notice and may not be included in the operating instructions.  Check the device for completeness, tightness and function before commissioning.  Never put a defective or non-functional device into operation! Contact the manufacturer or have the device checked by a qualified specialist.  Always work with care and the necessary caution!  Do not use excessive force under any circumstances!  Use safety equipment. Always wear protective goggles with side protection, ear protection, respi- ratory protection and safety shoes! ...

16 Ball Filling Needle 2 Chisel Retaining Spring 17 Hose Coupling 3 Chisel Hammer 18 Outlet Nozzle 4 Impact Wrench 19 Air Chamber Filling Adapter 5 Rod Grinder 20 Needle Adapter 6 Ratchet Screwdriver 21 Bit Adapter 7 Bit Assortment 22 Nut Assortment 8 Mounted Points 23 Adapter 9 Separating Chisel 24 Mounted Point Collet Chuck 10 Grinding Rollers 25 Valve Plug Attachment 11 Pointed chisel 26 Air Chamber Filling Adapter 12 Flat Chisel 27 Plug Nipple 1/8“ internal thread 13 Grinding Roller Holder 28 Plug Nipple Assortment 14 Teflon Tape 29 Allen Wrench 15 Oil Bottle © by WilTec Wildanger Technik ...

BEFORE START-UP  Seal the supplied plug nipple with Teflon tape and then screw it into the compressed air connec- tion.  Operate the compressed air unit only with an oiler.  Pressure reducer must be present on the compressor.  Install a water separator (filter) before the oiler.  The maximum operating pressure of your air tool is 6.2 bar. If you set your pressure minimum higher than 6.2 bar, your air tool may be overloaded.  During longer breaks in operation, we recommend cleaning and lubricating the air tool thoroughly.  When the unit is put back into operation, add some compressed air oil to th ...

Regular lubrication is a prerequisite for the proper functioning of your pneumatic tool and a long ser- vice life. The following lubrication options are available:  Using a mist lubricator: o A complete maintenance unit includes a mist lubricator and is attached to the compressor (not included).  Using a line oiler: o A line lubricator is installed in the immediate vicinity of the tool (approx. 50 cm distance), which supplies the tool sufficiently with oil. o If the pneumatic tool has been out of operation for several days, you must add 5-10 drops of special tool oil to the compressed air connection before switching it on. � ...

Regular lubrication is a prerequisite for the proper functioning of your pneumatic tool and a long ser- vice life. The following lubrication options are available:  Using a mist lubricator: o A complete maintenance unit includes a mist lubricator and is attached to the compressor (not included).  Using a line oiler: o A line lubricator is installed in the immediate vicinity of the tool (approx. 50 cm distance), which supplies the tool sufficiently with oil. o If the pneumatic tool has been out of operation for several days, you must add 5-10 drops of special tool oil to the compressed air connection before switching it on. � ...

Regular lubrication is a prerequisite for the proper functioning of your pneumatic tool and a long ser- vice life. The following lubrication options are available:  Using a mist lubricator: o A complete maintenance unit includes a mist lubricator and is attached to the com- pressor (not included).  Using a line oiler: o A line lubricator is installed in the immediate vicinity of the tool (approx. 50 cm distan- ce), which supplies the tool sufficiently with oil. o If the pneumatic tool has been out of operation for several days, you must add 5-10 drops of special tool oil to the compressed air connection before switching it on ...

compressed air devices in the set) 6,2 Bar Tool Impact Wrench Max. Release Torque ca. 310 Nm Max. Tightening Torque ca. 250 Nm Rotation Speed (max.) 7.000 rpm Vibration under Load <2,5 m/s² Square Socket ½“ Sound Pressure Level 89 db (A) Air Consumption ca. 350 l/min Weight ca. 2,3 Kg Tool Chisel Hammer Stroke Rate 3000/min Air Consumption ca. 350 l/min Compressed Air Connection ¼“ Tool Ratchet Screwdriver Max. Release Torque ca. 40 Nm Work Area (max.) M8 Sound Pressure Level 89 db (A) Vibration under Load <14,7 m/s² Rotation Speed (max.) 150 rpm Air Consumption ca. 310 l/min Weight ca. ...

Seite 30 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de ...

2 Gasket 28 Spring Washer 3 Housing 29 Hexagon Socket Twin-Head Screw 4 Housing Socket 30 Oil Screw 5 Spacer Ring 31 Absorber 6 O-Ring 32 Pin 7 Spring Washer 33 Spring Washer 8 Drive Shaft 34 Screw 9 Thrust Collar 35 Piston Housing 10 Chock 36 Piston 11 Clutch 37 Trigger 12 Steel Ball 38 Coiled Spring Pin 13 Steel Ball Holder 39 Coiled Spring Pin 14 Impact Mechanism Housing 40 Valve Block Seal 15 Ball Bearing 41 Valve Block 16 O-Ring 42 Hexagon Socket Twin-Head Screw 17 Gasket 43 Reducing Socket / Air Connection 18 Front Cover Plate 44 O-Ring 19 Cylinder 45 Compressed Air Re ...

13 Compressed Air Supply 7 Trigger 14 Air Control Screw 8 Clamping Sleeve 15 O-Ring 9 Gasket 16 Housing 10 Valve Pin 17 Piston 11 Metal Ball 18 Cylinder © by WilTec Wildanger Technik GmbH Seite 32 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de ...

13 Cylinder 2 Connection Socket 14 Rotor 3 Pin 15 Rotor Blade 4 Trigger 16 Socket 5 Housing 17 Cylinder Front Cover 6 Valve Pin 18 Ball Bearing 7 VentiValve 19 Nut 8 Spring 20 Head Plate 9 O-Ring 21 Washer (U-shaped) 10 Valve Screw 22 Spindle 11 Ball Bearing 23 Inhibitor 12 Cylinder Back 24 Cap Nut © by WilTec Wildanger Technik GmbH Seite 33 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de ...

20 Intermediate Bearing Pin 2 Housing 21 Intermediate Bearing Plate 3 Clamping Sleeve 22 Spacer 4 Trigger 23 Clamping Nut 5 Valve Pin 24 Ratchet Housing 6 Valve 25 Spacer 7 Spring 26 Crankshaft 8 O-Ring 27 Drive Socket 9 Valve Plug 28 Ratchet Head 10 Ball Bearing 29 Fuse Pin 11 Rear End Cover 30 Spring 12 Rotor 31 Direction Reverser 13 Lamella 32 Corrugated Disc 14 Cylinder 33 Ratchet Jaw 15 Front End Cover 34 Ratchet Anvil 16 Ball Bearing 35 Pin 17 Spring Washer 36 Corrugated Disc 18 Thread Bearing 37 Starting Disc 19 Intermediate Bearing 38 Retaining Ring © by WilTec Wilda ...