Wen MSA750 Manual 

Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions. If you use your tool properly and for intended purpose, you will enjoy years of safe, reliable service. IMPORTANT: NEED HELP? CONTACT US! Have product questions? Need technical support? Please feel free to contact us at: 800-232-1195 [email protected] WENPRODUCTS.COM (M-F 8AM-5PM CST) Model # MSA750 bit.ly/wenvideo For ...

Technical Data 2 3 4 5 6 7 9 General Safety Rules Specific Rules For The Miter Saw Stand Know Your Miter Saw Stand Assembly & Adjustments Operation Warranty 2 TECHNICAL DATA Model Number: Tubular Legs and Crossbars Diameter: Extension Rail Support Distance: Height to Saw Mounting Base: Saw Mounting Bracket Slot Length: Roller Length: Total Weight Support: Product Net Weight: MSA750 1.8 in. 34 in. (minimum) 69 in. (maximum) 29.5 in. 15 in. 9 in. 750 lbs 39.7 lbs ...

SAVE THESE SAFETY INSTRUCTIONS. 1. READ and become familiar with this entire instruction manual. LEARN the tool’s applications, limitations, and possible hazards. 2. AVOID DANGEROUS CONDITIONS. DO NOT use power tools in wet or damp areas or expose them to rain. 3. DO NOT use power tools in the presence of flammable liquids or gases. 4. ALWAYS keep your work area clean, uncluttered, well lit and well ventilated. DO NOT work on floor surfaces that are slippery with sawdust or wax. 5. KEEP BYSTANDERS AT A SAFE DISTANCE from the work area, especially when the tool is ...

1. For maximum stability, use the miter saw stand ONLY ON A FLAT, LEVEL SURFACE. 2. BE CAREFUL when raising or lowering the stand to prevent trapping fingers or hands. 3. DO NOT step or climb on the stand. 4. Before operation, ensure that the snap buttons on each leg are in the LOCKED POSITION and the material supports are LOCKED IN PLACE. 5. ENSURE that the miter saw is securely fastened to the stand to prevent unwanted movement of the saw. 6. DO NOT OVERLOAD the side extension arms. 7. The main frame can support 750 pounds of total weight (saw + material). DO NOT EXCEED THIS WEIGHT FOR ANY REASON. 8. DO NOT USE ...

Carefully unpack and remove all contents from the box. Use the illustrations below to become familiar with the various components of this miter saw stand. If any part is damaged or missing, please contact our customer service at (800) 232-1195, M-F 8-5 CST or email [email protected]. 5 No. Part Number Description Qty. 1 MSA750-001 Work Support Roller 2 2 MSA750-002 Saw Mounting Bracket Assembly 2 3 MSA750-003 Work Support Bracket 2 4 MSA750-004 Extension Arm 2 5 MSA750-005 Extension Arm Guide 2 6 MSA750-006 Locking Knob 6 7 MSA750-007 Miter Saw Stand Assembly 1 Mounting Hardware: Miter Saw Stand: 8 MS ...

deploy all four legs and lock them into place. 2. Insert each extension arm into the main frame of the crossbars (Fig. 2). 3. Insert the locking knob into the mainframe cross- bars to secure the extension arms (Fig. 3). 4. Slide the work support brackets onto the exten- sion arms (Fig. 4). 5. Secure the work support brackets in place using the locking knobs (Fig. 5). 6. Insert the work support rollers into the brackets (Fig. 6) and lock them in place using the locking knobs (Fig. 7). For Normal Cutting Operations: The top of the rollers should be level with the sur- face of the miter saw’s table. ...

The clamping pressure of each saw mounting bracket should be checked before it is attached to a miter saw. To Check The Clamping Pressure: When fitted across the two main crossbars with the locking handle in the down (locked) position, a bracket should be firm and exhibit no signs of movement. Avoid using excessive force to deploy the locking lever to the down po- sition. Gently pressing the lever downwards with the palm of your hand should be all the force needed to operate the locking lever. To Adjust The Clamping Pressure: 1. Turn the clamp upside down to reveal the mechanism. 2. Loosen the lock nut (Fig. ...

miter stand’s tubular crossbar (Fig. 12). 6. Push the back of the brackets down to engage them onto the back crossbar (Fig. 13). 7. Lock the brackets into place by gently pressing down the locking levers (Fig. 14). 8. To ensure the stability of the miter saw stand and the mounted machine during cutting operations, adjust the OPERATION Fig. 14 Fig. 12 Fig. 13 position of the miter saw so the fence of the miter saw is aligned with the center of the rear crossbar of the stand. 9. When the miter saw is correctly positioned on the stand, securely tighten the four mounting nuts. MOUNTING UNUSUAL MIT ...

this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN con- sumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase. Ninety days for all WEN products, if the tool is used for professional use. SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited Warranty and, to the extent permitted by law, any warranty ...