TriMark e-ASK UM27 Installation Instructions Manual

CAN Multiplex System CAN Multiplex System Installation & Instructions (UM27 ~ 24324-03)

Introduction .................................................................................. 1 e-PAD Operation and Features ................................................... 1 Locking Doors With Keypad ...................................................... 1 Unlocking Doors With Keypad ................................................... 1 e-FOB Operation and Features .................................................. 2 Additional Features ...................................................................... 2 Dome/Porch Light Activation ..................................................... 2 e-PAD Anti-tamper Deactivating Feature .................................. 2 Teaching Keypad New Authority/Access Codes ...................... 2 Assign New Access Codes ........................................................ 3 Teaching Additional Transmitter FOBs ..................................... 4 e-ASK CAN DIP Switch Configuration ...................................... 5 Wiring Assignments..................................................................... 7 Troubleshooting ........................................................................... 8

installation and use of TriMark’s CAN e-ASK system. The e-ASK system comes with the following components: e-FOB keyless entry radio frequency [RF] FOB transmitter and receiver e-PAD keypad user interface e-PAD Operation and Features The e-PAD is shipped with default authority and access codes. Unless the OEM or dealer has changed default codes, the authority and access codes are as follows: 1 Digit 1 Digit 2 Digit 3 Digit 4 Digit 5 1 / 2 3 / 4 5 / 6 7 / 8 9 / 0 Digit 1 Digit 2 Digit 3 Digit 4 Digit 5 7 / 8 7 / 8 7 / 8 7 / 8 7 / 8 Access code: Authority code: Locking Doors With Keypad Press and hold down the 1 / 2 button for 1-2 seconds. An access code is not needed to lock the doors. Unlocking Doors With Keypad Entering a valid 5-digit access code enables a secure operation. After entering an access code, the keypad is enabled for 5 seconds and an additional button press initiates a secure operation, such as unlocking the doors. 1. Enter access code. 2. Press and release: 1 / 2 button to unlock driver door, or 3 / 4 button to unlock driver and passenger doors Note: The authority code does not allow for secure operations. It is only used to assign access codes (see page 3 for information on setting codes). The secure keypad operations are set depending on the system configuration.

Note: The RF features are an option that may not be available on your vehicle. The CAN module and transmitters are shipped programmed. After making all necessary wiring connections, (see page 6 for wiring information), the e-FOB system will function as shown. Additional Features Dome/Porch Light Activation The dome light is activated for a timed duration (20 seconds) whenever the system is unlocked from keypad or FOB transmitter. This is an optional feature that the OEM may not have installed. e-PAD Anti-tamper Deactivating Feature After repeated attempts to enter code (20 button presses without enabling), the keypad enters an inactive mode that disables button for 1 minute. This helps prevent access by entering random codes. The keypad does not beep while the system is disabled. Teaching Keypad New Authority / Access Codes When a new authority code is assigned, all existing authority and access codes are erased. Note: The authority code assigned following these instructions is also an access code saved to the (1 / 2) button. 1. Touch the yellow wire of keypad to ground. There will be a three- second beep. When the beep starts, remove the GND. 2. Enter a five-digit code. 3. Enter the new code again. Button Function Lock Locks all doors Unlock Unlocks all doors

vehicle, fleet manager, etc.) who manage the distribution of access codes to vehicle users. The authority code should be changed when the vehicle is sold. The authority code does not enable secure functions (lock/ unlock doors, etc.). It is only used to assign access codes. The following area can be used to document the authority code: Authority code: Assign New Access Codes With a valid authority code (see page 2), an access code can be programmed with the following instructions. 1. Press the (5 / 6) button for 5 seconds, the keypad will beep. (Backlight LEDs of the keypad flash indicating the learn mode.) 2. Enter the 5-digit authority code (see page above). Keypad will provide a long beep that will stop after you have defined an access number. 3. Press and release any button. This button corresponds to the access number being programmed. For example, press (1 / 2) button for access code #1 and press (3 / 4) button for access code #2. 4. Enter in your new 5-digit access code. The keypad will provide 3 beeps. 5. Re-enter new access code. The keypad will provide 3 beeps. Repeat process to assign additional access codes.  Up to 5 different access codes can be assigned at one time. As additional access codes are defined, pre-existing access codes are overwritten. For example, if a new access code is assigned for access #3, the previous access #3 code is no longer valid.  A one second beep means that an error was made and no code was programmed. 3 Digit 1 Digit 2 Digit 3 Digit 4 Digit 5