Toro 30392 Installation Instructions Manual

CE Kit Groundsmaster® 7200/7210 Traction Unit Model No. 30392 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 106-6754 1. Warning—do not touch the hot surface. 2. Cutting/dismemberment hazard, fan and entanglement hazard, belt—stay away from moving parts. 112-1689 1. Tipping hazard—do not operate on slopes greater than 14 degrees. © 2009—The Toro® Compan ...

Procedure Description Qty. Use Latch locator bracket 1 Bolt (5/16 x 3/4 inch) 1 Lock nut (5/16 inch) 1 Locking latch 1 Hood support 1 Bolt (5/16 x 2 inches) 2 Washer (5/16 inch) 4 1 Lock nut (5/16 inch) 2 Install the locking latch. Floor locking latch 1 Carriage bolt (1/4 x 3/4 inch) 2 2 Lock nut (1/4 inch) 2 Install the floor plate locking latch (for 2008 and later models) Hood handle 1 Plastite screw (1/4 x 1.12 inch) 2 Washer (5/16 inch) 2 3 Clamp 1 Install the hood handle. Bolt (5/16 x 1-1/4 inches) 2 Retaining nut (5/16 inch) 2 4 Push nut 2 Secure the belt cov ...

Latch Parts needed for this procedure: 1 Latch locator bracket 1 Bolt (5/16 x 3/4 inch) 1 Lock nut (5/16 inch) 1 Locking latch 1 Hood support 2 Bolt (5/16 x 2 inches) 4 Washer (5/16 inch) 2 Lock nut (5/16 inch) Procedure 1. Unlatch and raise the hood. Use the prop rod to hold it in place. Locate the upper (rear) metal frame support running across the underside of the hood. 2. In the upper, left corner of the metal frame, locate the hole drilled in the face of the support. Use a drill to open the hole to accept a 5/16 inch (8 mm) fastener. 3. Install the latch locator bracket as shown in Figure 1 using a bolt (5/16 x 3/4 in ...

support 3. Latch locator bracket 5. Locking latch, catch facing forward 2. Lock nut (5/16 inch) 4. Bolt (5/16 x 3/4 inch) 6. Locking nut 10. Install the catch plate to the left hand frame member, directly below the installed latch, at the existing holes as shown in Figure 2. Secure the catch plate to the frame member with two bolts (5/16 x 2 inches), two washers (5/16 inch) and two lock nuts (5/16 inch). 4 ...

4. Washer (5/16 inch) 2. Catch plate 5. Lock nut (5/16 inch) 3. Bolt (5/16 x 2 inches) Note: The bolts should be approximately centered in the slots of the catch plate. 11. Close the hood slowly to see if latch catches. If it does not, loosen the bolts securing the catch plate to the frame member and adjust the plate as necessary. Tighten the bolts and verify the latch catches. 2 Installing the Floor Plate Locking Latch (for 2008 and later models) Parts needed for this procedure: 1 Floor locking latch 2 Carriage bolt (1/4 x 3/4 inch) 2 Lock nut (1/4 inch) Procedure 1. Raise the floor plate (Figure 3). Figure 3 1. Hole in f ...

1-1/2 inches (3.8 cm) (Figure 4). Install the clamp around the rail at this location. 3. Using the clamp as a template, mark a spot in the hood and drill a 5/16 inch (8 mm) diameter hole. 4. Install a washer (5/16 inch) and plastite screw (1/4 x 1.12 inch) through the clamp and drilled hole in the hood and into the hood handle. 5. With the hood handle in the approximate position shown in Figure 4 mark the second spot to drill 4.8 inches (12.2 cm) from the initial drilled hole. Swing the hood handle out of position and drill a 0.3125 inch diameter hole at that position in the hood. 6. Install a washer ...

Parts needed for this procedure: 2 Bolt (5/16 x 1-1/4 inches) 2 Retaining nut (5/16 inch) 2 Push nut Procedure Perform this procedure for the right and left side belt covers. 1. Remove the hand knobs securing the belt covers to the mower deck. Remove the belt covers. 2. Install a retaining nut at the forward hole in the deck bracket. Figure 5 Left side belt cover shown. 1. Belt cover 5. Bolt (5/16 x 1-1/4 inches) 2. Mower deck 6. Hand knob 3. Retaining nut 7. Push nut 4. Deck bracket 3. Install the bolt into the belt cover using a push nut (5/16 inch). Install the belt cover with the bolt (5/16 x 1-1/4 inches). Replace the ha ...

Parts needed for this procedure: 1 Safety decal, 112-1689 1 Safety decal, 106-6754 Procedure Install each decal as follows: 1. Thoroughly clean the area where you will install the decal. 2. Dampen the area with water or mildly soapy water. 3. Peel the decal from the backing and install it in place. 4. Squeegee across the surface of the decal, starting at the center of the decal and working toward the edges, using overlapping strokes. Figure 7 1. Decal 110-6754 3. Locking latch 2. Hood 4. Decal location G004790 1 2 3 Figure 8 Install over existing decal at location shown 1. Decal 112-1689 3. Install decal 112-1689 at this locatio ...