TOORX BRX60 Instruction Manual

4 3 END CAP FOR REAR STABILIZER 2 36 ROUND END CAPS Φ25.4 2 4 CARRIAGE BOLT M10*65 4 37 END CAP FOR WIRE 1 5 FRONT STABILIZER 1 38 POWDER SPACER 1 6 END CAP FOR FRONT STABILIZER 2 39 SELF-TAPPING SCREW ST5*15 4 7 CURVE WASHER Φ10*Φ22 4 40 SELF-TAPPING SCREW ST5*15 8 8 DOMED NUT M8 4 41 CRANK L/R 1/1 9 QUICK RELEASE KNOB 1 42 BB ASSEMBLY 1 10 ALLEN SCREW M8*16 4 43 SEAT POST PLASTIC SLEEVE 1 11 SEAT 1 44 SENSOR BRACKET 1 12 FRONT POST 1 45 SPRING 1 13 TENSION KNOB +CABLE UPPER 1 46 FRENCH NUT 4 14 SENSOR WIRE MIDDLE 1 47 PULLY 1 15 SCREW M5*10 2 48 END CAP FOR CRANK 2 16 SPACER 1 49 SPACER FOR MAGNET 2 17 SQUARE WASHER 1 50 MAGNETIC ASSEMBLY 1 18 COMPUTER 1 51 HEX HEAD BOLT 1 19 HANDLE BAR 1 52 FLYWHEEL 1 20 HAND PULSE WIRE LOWER 2 53 IDLER PULLEY 1 21 CLAMP 1 54 SPRING 1 22 ALLEN SCREW M8*20 2 55 HEX HEAD NUT M8 1 23 T TYPE KNOB 1 56 HEX HEAD BOLT 1 24 SELF-TAPPING SCREW ST4*20 2 57 CHAIN COVER L/R 1/1 25 FLAT WASHER Φ4.2*Φ12*1 2 58 END CAP FOR CHAIN COVER 2 26 HAND PULSE SENSOR 2 59 HEX HEAD BOLT M6*25 1 27 FOAM GRIP FOR HANDLEBAR 2 60 HEX HEAD NUT M6 2 28 SEAT POST 1 61 SLIDING SEAT 1 29 NYLON NUT M8 5 62 CARRIAGE BOLT M8*40 1 30 SPRING WASHER Φ8 3 63 BELT 1 31 FLAT WASHER Φ8*Φ17*1.5 4 64 KNOB 1 32 TENSION CABLE LOWER 1 65 SENSOR WIRE LOWER 1 33 CLAMP COVER 1

4 EXPLODED DIAGRAM 2 3 4 4 4 4 5 6 6 1 7 8 7 7 7 8 8 8 9 10 35 35 12 13 14 15 10 19 20 21 22 23 25 24 27 24 25 26 27 11 32 33 34R 34L 36 36 37 28 30 31 29 64 16 17 62 61 41L 3 65 18

5 43 39 40 47 42 22 31 29 29 39 39 39 40 40 44 45 51 50 49 49 53 55 56 57L 57R 58 58 59 60 38 46 46 52 54 63 41L 41R 46 46 48 48

No. Description Drawing Q’ty 4 Carriage Bolt M10*65 4 7 Curve Washer Φ10*Φ22 4 8 Domed Nut M10 4 10 Allen Bolt M8*16 4 23 T type Knob 1 33 Clamp cover 1 35 Curve Washer Φ8*Φ20 4 Allen Key 6mm 1 Box Wrench 1 Above described parts are all the parts you need to assemble this machine. Before you start to assemble, please check the hardware packing to make sure they are included.

PART NO. DESCRIPTION Q’TY 1 Main Frame 1 2 Rear Stabilizer 1 5 Front Stabilizer 1 11 Seat 1 12 Front Post 1 18 Computer 1 19 Handlebar 1 28 Seat Post 1 34 Left & Right Pedal 1/1 User Manual 1 Hardware bag 1 NO.1 NO.5 NO.12 NO.18 NO.19 NO.11 NO.34 NO.28 NO.2 18

washer (7) and domed nut (8). (b) Then, attach rear stabilizer (2) to main frame (1), tighten with 2 sets of carriage bolt (4), curve washer (7) and domed nut (8). STEP 2 (a) Take front post (12) and connect middle sensor wire (14) with lower sensor wire (65). (b) Adjust the tension control knob (13) to level 8, then connect it with the lower tension cable (32). Insert front post (12) into main frame (1) and tighten with 4 sets of allen screw (10) and curve washer (7). 8 8 1 2 4 4 13 10 7 10 7 32 13 12 14 32 65 14 65

Slide the Cable wire from the Upper Tension Connector in between the opening on the wire holder on the Lower Tension Connector. Pull the Upper Tension Connector backward and slide the wire through the slot on the bracket. Drop down the Connector so the fitting sits firmly on top of the bracket. NOTE: In able to hold the Front Post while connecting the cables and wires， extra help may be needed.

front post, Secure by using the clamp (21), allen screw (22), clamp cover (33) and T type knob (23). (b) Insert the hand pulse wires (20) through end cap for wire (37) and insert through the hole in the front post, pull the hand pulse wires (20) through the hole at the top of the front post and insert end cap for wire(37) into the front post. (c) Connect the hand pulse wires (20) and middle sensor wire (14) to the back of the computer (18) . Attach the computer onto the bracket of front post. Secure by using two screws (15) which are pre-assembled on the back of computer. STEP 4 Take the Quick release knob (9) off from main frame . Insert seat post (28) into the main Frame (1), then tighten with knob (9). Attach seat (11) to seat post, tighten with carriage bolt (62), square washer(17),spacer (16) and knob (64). 19 21 22 23 18 20 33 9 28 11 64 16 17 62

their appropriate crank arm (41). The right pedal is on the right hand side of the cycle as you sit on it. Note that the right pedal should be threaded on clockwise and the left pedal on counter-clockwise. CHECK ALL BOLTS AND NUTS ARE TIGHTENED BEFORE USING THE MACHINE 34R 34L 41L

FUNCTION BUTTONS MODE 1. Press the button to select TIME, DISTANCE and CALORIES to preset. 2. Press the button for selection function display value on LCD, or enter after setting. 3. Press the button and hold for 2 seconds to reset all value except Odometer to be zero. (When the user replace batteries, all the values will reset to ZERO automatically.) SET 1. To set up the target value of TIME, DISTANCE and CALORIES. 2. Press the button and hold for 2 seconds to speed up the increment. RESET 1. Press the button to reset function value when setting. 2. Press the button and hold for 2 seconds to reset all value except Odometer to be zero. (When the user replace batteries, all the values will reset to ZERO automatically.) FUNCTIONS & OPERATIONS Time Accumulates total time from 00:00 up to 99:59. The user may preset target time by pressing SET & MODE button. Each increment is 1 minute. Automatically count down from targeting value during exercise. Calories Accumulates calories consumption during training from 0 to max. 9999 calories. The user may also preset the target calorie before training by press SET & MODE button. Each setting increase is 1 cal till 1000, Each increment will be 10 cal when calories is over 1000. Automatically count down from targeting value during exercise. Note : This data is a rough guide which can not be used in medical treatment

display the Odometer value. Pulse The monitor will display the user's heart rate in beats per minute during training. Speed Displays your workout speed value in Kilometer per hour. Distance Displays the accumulative distance traveled during each workout up to a maximum of 99.9 MILE. Note: 1. If the computer displays abnormally, please re-install the battery and try again. 2. Please install 2 pcs of AA 1.5V batteries in the battery case on the back of monitor. (Whenever batteries are removed, all of the functions values will be reset to zero.) 3. The batteries must be removed from the appliance before it is scrapped and that they are disposed of safely. 4. While the user starts to do exercise, the display will show out the workout value automatically. Once stop exercise over 4 minutes, the display will turn off. But the workout value of odometer will be hold. While user starts exercise again, workout value of odometer will be accumulated continuously. 5. After the monitor is power on or press MODE key, the LCD will display all functions values from Time – Calories – Odometer – Pulse – Speed – Distance. Each value will be held for 6 seconds.

15068 - Pozzolo Formigaro (AL) - Italy www.toorx.it - [email protected]