TechnipFMC Smith Meter AccuLoad IV Series Installation And Maintenance Manual

Bulletin MN06201 Issue/Rev 0.1 (2/20) Installation and Maintenance Manual Smith Meter® AccuLoad® IV MANUAL ...

Important All information and technical specifications in this documentation have been carefully checked and compiled by the author. However, we cannot completely exclude the possibility of errors. TechnipFMC is always grateful to be informed of any errors. Contact us on the website. Smith Meter is a registered trademark of TechnipFMC. Caution The default or operating values used in this manual and in the progra ...

AccuLoad IV Installation and Maintenance Manual Table of Contents Table of Contents 1 – Introduction........................................................5 1.1. Warnings and Precautions...........................5 1.2. Weights & Measures Requirements............7 2 – Pre-Installation Considerations.......................9 2.1. Environment.................................................9 2.2. Mechanical... ...

13 – Maintenance...................................................67 13.1 Enclosure Maintenance..........................67 13.2. A4I Kit Retrofit Installation......................68 13.3 Touch Screen Recalibration Procedures...69 13.3.1 Equipment and Other Requirements......69 13.3.2 Accessing the Display Module menu.....70 13.3.3 Display Module touch screen recalibration procedure...................... ...

AccuLoad IV Installation and Maintenance Manual Introduction 1 – Introduction This manual provides guidance for the installation of AccuLoad preset models ST, QT, N4 and SA. When installed following the guidelines contained in this manual, the AccuLoad will provide many years of safe, accurate and reliable delivery control. This manual addresses the requirements specific to the AccuLoad and it is assumed that ...

Electrostatic Discharge Precautions The electronic components in the AccuLoad are susceptible to damage by static discharge. To minimize the risk of damage, the following precautions should be followed: • Before touching a circuit board with hands or tools, personnel/tools should be grounded using a wrist strap. • Avoid touching components or traces on the circuit boards and handle by the edges/ mounting hol ...

1.2 Weights & Measures Requirements The AccuLoad is a device marketed for a global market. Requirements vary depending on the region. It is a user requirement to verify that the AccuLoad is programmed and operated in a manner consistent with local codes and that proper notification (permit for use) or registration has been filed with the local authority or jurisdiction. AccuLoad IV Installation and Maintenance M ...

2 – Pre-Installation Considerations 2.1. Environmental Considerations Models ALIV-ST-XP and ALIV-QT-XP The enclosures of Explosion / Flame proof models are manufactured from aluminum alloy, and are designed to be operated in normal environmental conditions free of corrosive agents. In areas including but not limited to environmentally corrosive atmospheres, special considerations for additional environmental p ...

Table 1. Cable Access Model Top Cable Access Bottom Cable Access AccuLoad ST 2 – 1” 11.5 NPT 3 – 1.25” 11.5 NPT AccuLoad QT 1 – 1” 11.5 NPT 2 – 1.25” 11.5 NPT 5 – 1” 11.5 NPT AccuLoad N4 3 – 1.75” AccuLoad SA MMI 3 – 1.75” AccuLoad SA FCM 10 – 2” 5. While the AccuLoad is rated to operate in ambient temperatures up to 60 degrees Celsius, it is advisable to keep all electronics as ...

AccuLoad IV Installation and Maintenance Manual Pre-Installation Considerations 3. For Ethernet connections, a minimum of CAT-5 rated cable should be used and the Ethernet wiring practices described in the Ethernet standard should be followed for cable lengths etc.. 4. Connectors are sized for a maximum of 14 gauge wire, consult the local electrical codes for the minimum wire size required for your applicatio ...

AccuLoad IV Installation and Maintenance Manual Installation 3 – Installation The general steps in the installation process are to physically mount the AccuLoad, elec­ trically connect it to the associated equipment and then tailor the configuration database parameters to suit the specific operational and measurement environment. The following sections cover the mounting and wiring. Refer to the AccuLoad IV ...

AccuLoad IV Installation and Maintenance Manual Installation (f) Grounding: The Touch Keypad sensor is protected by an intrinsic safe barrier, the enclosure must be grounded as per national electrical code regulations, for example NEC/CEC, etc. Equipment bonding shall be provided at the external grounding facility terminal, external connection is not required when using metallic conduit or armored cable. Exte ...

AccuLoad IV Installation and Maintenance Manual Installation 3.2. General Requirements (a) It is imperative that the electrical installation be performed by a competent individual that is familiar with associated risks involved with the installation, operation, and maintenance, of electrical equipment in hazardous (classified) locations. This individual must possess knowledge of local, national electrical code ...

AccuLoad IV Installation and Maintenance Manual AccuLoad Models 4 – AccuLoad Models There are four models of the AccuLoad: the ST, QT, N4, and SA shown in the following figures: Figure 1. AccuLoad IV-ST Figure 2. AccuLoad IV-QT ...

AC WIRING TRAY 'A' 'B' 'C' 'D' DC WIRING TRAY DC WIRING TRAY DC WIRING TRAY AccuLoad IV Installation and Maintenance Manual AccuLoad Models Figure 3. AccuLoad Model N4 Figure 4. AccuLoad Model SA ...

AccuLoad IV Installation and Maintenance Manual AccuLoad Models There is a common set of electronic modules used in the different AccuLoad models as follows: THMI – The touchscreen display module mounted in the front panel of the unit. A4M – The main CPU and I/O module. All AccuLoad models will contain at least one A4M module. A4B – Provides expanded I/O capability to support additional load arms. Note: M ...

AccuLoad IV Installation and Maintenance Manual AccuLoad Models Table 6. Functions and capacities by module Module Usage/Location Power Interfaces Description THMI Front cover of: ST QT N4 SA - MMI 24 VDC Ethernet USB Serial Provides user interface touch screen. Connects to the A4M with Ethernet. A4M ST QT N4 SA - FCM 93 – 230 VAC Meter Pulse Input Pulse Outputs Digital I/O AC/DC Analog I/O Ethernet Main I/O ...