TE Connectivity 2352901 Series Quick Installation Manual

SWITCH QUICK INSTALLATION GUIDE INTRODUCTION The 2352901 series is a managed redundant PoE Ethernet switch with 8x 10/100/1000 Base-T(X) P.S.E. and 4x 10/100/1000Base-T(X) ports, specifically designed for the toughest environment and fully compliant with EN50155. The switch supports the Ethernet Redundancy protocol, TE-Ring (recovery time < 30ms over 250 units), TE- Chain, MSTP/RSTP/STP (IEEE 802.1s/w/D), can protect your mission critical appli- cations from network interruptions or temporary malfunctions with its fast recovery technology. 2352901 also supports Power over Ethernet a system to transmit electrical power up to 30 watts, along with data, to remote devices over standard twisted-pair cable in an Ethernet network. Each switch has 8x10/100/1000Base-T(X) P.S.E. (Po- werSourcing Equipment) ports. P.S.E. is a device (switch or hub for instance) that will provide power in a PoE connection. The series supports wide operating temperature from -40°C to 75°C and can also be managed centralized by TE-Vision, Telnet and console (CLI) configuration. Therefore, the switch is one of the most reliable choices for EN50155 highly-managed Ethernet applications. PACKAGE CONTENTS The device is shipped with the following items. If any of these items is missing or da- maged, please contact your customer service representative for assistance. • 2352901 series Ethernet switch • CD Containing software • Quick Installation Guide PREPARATION Before you begin installing the device, make sure you have all of the package contents available and a PC with Microsoft Internet Explorer 6.0 or later, for using web-based system management tools. Safety & Warnings Elevated Operating Ambient: If installed in a closed environment, make sure the operating ambient temperature is compatible with the maximum ambient temperature (Tma) specified by the manufacturer. Reduced Air Flow: Make sure the amount of air flow required for safe operation of the equipment is not compromised during installation. Mechanical Loading: Make sure the mounting of the equipment is not in a hazardous condition due to uneven mechanical loading. DIMENSIONS (in mm) EN 50155 SWITCH Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern. MAIN * * * * * * * * 

SWITCH QUICK INSTALLATION GUIDE INSTALLATION The device can be fixed to the wall. Follow the steps below to install the device on the wall. Step 1: Hold the device upright against the wall Step 2: Insert four screws through the large opening of the keyhole-shaped aper- tures at the top and bottom of the unit and fasten the screw to the wall with a screw driver. Step 3: Slide the device downwards and tighten the four screws for added stability. PANEL LAYOUTS WIRING For pin assignments please refer to the instructions below: Grounding Grounding and wire routing help limit the effects of noise due to electromagnetic in- terference (EMI). Run the ground connection from the grounding pin on the power connector to the grounding surface prior to connecting devices. Power port pinouts The 2352901 series uses the M23 5-pin female connector on the front panel for the dual power inputs. Step 1: Insert a power cable to the power connector on the device. Step 2: Rotate the outer ring of the cable connector until a snug fit is achieved. Make sure the connection is tight. Console port pinout V1+ V1- V2+ V2- Pin No. Description Pin No. Description 1 BI_DC+ 5 BI_DB+ / PoE Vout- 2 BI_DD+ 6 BI_DA+ / PoE Vout+ 3 BI_DD- 7 BI_DC- 4 BI_DA- /POE Vout+ 8 BI_DB- / PoE Vout- Relay NC NC NC M12 A-Code Ethernet ports Relay output ports pinouts The switch uses the M12 A-coded 5-pin female connector on the front panel for relay output. Use a cable with an M12 A-coded 5-pin male connector to connect the relay. The relay contacts will detect user-configured events and form an open circuit when an event is triggered. -1 and -4 1 Reset Button 2 Power1 status LED 3 Power2 status LED 4 R.M. Status LED 5 Ring Status LED 6 Fault LED 7 Power Connector 8 Non-PoE Gigabit Ethernet ports (with bypass) 9 PoE enabled Gigabit ether- net ports 10 Link/ACT LED for non-PoE enabled Gigabit ports 11 Speed LED for non-PoE Gigabit ports 12 Link/ACT LED for PoE ena- bled Gigabit ports 13 PoE Indicator for PoE ena- bled Gigabit ports 14 Speed LED for PoE enabled Gigabit ports 15 Console port 16 Relay output port 1 6 5 4 3 2 7 8 9 10 11 14 13 12 16 15 1 7 2 8 3 4 5 6

SWITCH QUICK INSTALLATION GUIDE LED INDICATORS After installing the switch and connecting cables, the green power LED should turn on. Please refer to the following table for LED indication. LED Color Status Description PW1 Green On DC power module 1 activated PW2 Green On DC power module 2 activated R.M Green On Device operating in Ring master mode Ring Green On Ring enabled Blink Ring structure is broken Fault Amber On Errors occur (i.e. power failure or port malfunction) 10/100/1000Base-T(X) P.S.E. Ethernet ports LNK/ACT Green On Port is linked Blink Transmitting data PoE Green On Power supplied over Ethernet Speed Green On Port is running at 1Gbps Amber On Port is running at 100 Mbps - Off Port is running at 10Mbps 10/100/1000Base-T(X) Ethernet ports Speed Green On Port is running at 1000 Mbps Amber On Port is running at 100Mb - Off Port is running at 10Mbps Revision 1_0, 20 August 2019 Pin No. Description Pin No. Description 1 BI_DA+/Vout+ 5 BI_DD+ 2 BI_DA-/Vout+ 6 BI_DD- 3 BI_DB+/Vout- 7 BI_DC- 4 BI_DB-/Vout- 8 BI_DC+ M12 X-Code Ethernet ports NETWORK CONNECTION The device provides Ethernet ports in M12 connector type. According to the link type, the switchuses CAT 3, 4, 5,5e UTP cables to connect to any other network devices (PCs, servers, switches,routers, or hubs). Please refer to the following table for cable specifications Pin No. Type Max Length Connector 10BASE-T Cat. 3, 4, 5 100Ω UTP 100m M12 A/X-Coding Connector 100BASE-T Cat. 5 100Ω UTP UTP 100m M12 A/X-Coding Connector 1000BASE-T Cat. 5/5e 100Ω UTP UTP 100m M12 A/X-Coding Connector Partnumber Input power PoE power budget 2352901-1, -2 and -3 12-36V 90W 2352901-4 72-110V 90W PoE power budget LOGIN Default IP adress: 192.168.10.1 Default username: admin Default password: admin Refer to the user manual for further instructions RESET To restore the device configurations back to the factory defaults, press the Reset but- ton for 5 seconds. Once the power indicator starts to flash, release the button. The device will then reboot and return to factory defaults.