Smart Flex SF-100 Manual 

Text of Smart Flex SF-100 Manual 

Table of Contents ( SF-100 )

Warnings and Safety Instructions Electrical Safety Weight Ratings and Restrictions Unpacking the Parts Included Assembly of the Legs to the Base SF-100 All Built-in / Connected Control System Wired Remote Control Operation How to Sync Two Twin XL Bases into a King Troubleshooting Warranty Information Contact Information 1 2 5 6 7 9 9 11 12 13 14 16

Warnings and Safety Instructions

The main priority at Smart Flex is making sure that all purchasers of our products enjoy them safely. We ask that everyone reads this manual carefully and with caution. Please observe all warnings and safety instructions. FAILURE to adhere to any of the warnings or cautions listed in this manual could potentially void the warranty. At the end of this manual, there will be contact information. Please email or call with quest

In addition: Any lifting of this product should be done by a

minimum of 2 persons. Product should always be in the flat position before lifting. Residential (In-Home) Use Only Smart Flex makes no assertion that its products are designed for any medical use. The product is not considered to be a "hospital or medical" bed for commercial or residential use. Smart Flex, Inc. has not designed this product to meet hospital or medical standards as defined by the

IMPORTANT NOTE: To ensure maximum safety, this product

should be plugged into an electrical surge protector and not directly into the outlet. (Surge Protector is not supplied with this adjustable bed) Be sure to always unplug this adjustable bed frame from the electrical outlet (surge protector) before performing any cleaning or maintenance of the bed frame. Disconnect any cord or cable safely by first removing the plug from the outlet (s

Weight Ratings and Restrictions

Overload of Weight: In the case that an overload of weight is placed on the head or foot mechanism, the control unit will get overheated and shut down. The control unit will resume all functions after the excess weight is removed from the bed and its temperature has decreased. The recommended weight limits on this adjustable bed is 750lbs. Lifting and Lowering Cycles: Do not sit on the head or the foot of the bed while chang

• Unplug this product from the electrical outlet (surge protector)

before attaching or removing any wires connected to the con- trol box or any other additional accessories. • Do not insert any items into the control box input or any port/ input that is not intended for use with this product, or that does not fit in any port/ input. • Do not use this product in the vicinity of aerosol spray products or oxygen products /equipments. • If there is any

Unpacking the Parts Included

1. Open the carton box and unfold the metal bed frame. 2. Then open all the boxes containing all the parts and cut zip ties for wired remote, power cord and mattress bar. 3. Please check to make sure you have all the parts of your adjustable bed - Legs and bolts: 2 pcs center legs, 4 pcs center leg bolts, 4 pcs corner legs, 4 pcs corner leg bolts. - 1 Allen key. - 4 pcs Motor pins, 4 pcs Motor clips. - Foot mattress retainer

Assembly of the Legs to the Base

1. First, open up your SF-100 Box. 2. Unfold and lay down the bed base. 3. Next, tighten the center legs in the center of the frame using the supplied Allen Key and center leg bolts. 4. Then tighten the 4 corner legs with corner leg bolts (Allen key not needed). 5. Use the adjustable leg heights to fit your adjustable bed frame 3 1 2 4 5 6 8

SF-100 All Built-in Control System

1. The Power Supply/ Transformer is built-in to the Head Motor. 2. A Control Circuit Board is inside the Head Motor as the center of control. 3. As connected to the Head Motor, the top cord is connected to the Foot Motor and the bottom cord is connected to the wired remote control. 4. You should have your Motor system already built in and connected as shown in figure 4. 9 SF-100 Head Motor Connect to foot

Smart Flex Indoor Furnishing Owners Instructions: