Siemens SIMATIC Ident Compact Operating Instructions

C79000-G8976-C492-01, 12/2017 1 SIMATIC Ident RFID systems Transponder corner bracket for MDS D160, D460 and D560 Compact Operating Instructions Legal information Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. DANGER indicates that death or severe personal injury will result if proper precautions are not taken. WARNING indicates that death or severe personal injury may result if proper precautions are not taken. CAUTION indicates that minor personal injury can result if proper precautions are not taken. NOTICE indicates that property damage can result if proper precautions are not taken. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage. Qualified Personnel The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems. Proper use of Siemens products Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed.

2 C79000-G8976-C492-01, 12/2017 1 Characteristics Transponder corner bracket for MDS D160, D460 and D560 Characteristics Area of application The transponder corner bracket can be mounted at an angle of 45° to the corner of a workpiece holder, so that the MDS Dx60 transponder attached to it can be equally processed regardless of the conveying direction (longitudinal or trans- verse conveyance). Operating temperature -25°C ... +85°C Material PA6-GF Color Black Dimensions (W x H x D) 19 x 27.5 x 18 mm (without alignment pin) 2 Ordering data Table 2-1 Ordering data for transponder corner bracket for MDS D160, D460 and D560 Article number Transponder corner bracket for MDS D160, D460 and D560 (packaging unit 50 units) 6GT2690-0AN00 3 Installation Note Temperature during installation work The transponders must be mounted and disassembled at room temperature. Mounting the transponder and the transponder corner bracket To mount the transponder, follow these steps: 1. Insert the transponder into the transponder corner bracket diagonally from above. 2. Press the transponder down slightly until the transponder is latches in the transponder corner bracket. 3. Fasten the transponder corner bracket with a M4 cylinder head screw. Note Additionally securing the fixing screw If the transponder corner bracket is exposed to frequent temperature fluctuations and mechanical shock, additionally secure the fixing screw, e. g. with screw retainer finish or lock nuts. Disassembling the transponder To disassemble the transponder, follow these steps: 1. Use a suitable tool, e.g. a flat screwdriver, to pry the transponder out of the transponder corner bracket.

C79000-G8976-C492-01, 12/2017 3 4 Field data The sensing ranges are based on the distance between the reader or antenna and the edge of the transponder corner bracket. ① Reader ② Conveyor direction ③ Transponder corner bracket for MDS D160, D460 and D560 ④ Workpiece holder Note Effect of inclined position The field geometry becomes distorted if you mount the transponder in an inclined position. It is recommended to test the respective configuration before use, as the field geometry differs from the standard configuration in form. Figure 4-1 Distorted field geometry When the transponder corner bracket is aligned at 45°, the working distances and boundary distances are around 75% of the values of a parallel alignment. Due to the distorted field geometry, it is advisable to perform a test with the final mounting position of the transponder corner bracket and the reader. The minimum distances and transmission windows can be found in the system manuals for "SIMATIC RF200" and "SIMATIC RF300".

4 C79000-G8976-C492-01, 12/2017 5 Technical specifications Table 5-1 Technical specifications of the transponder corner bracket for MDS D160, D460 and D560 6GT2690-0AN00 Product type designation Transponder corner bracket for MDS D160, D460 and D560 Mechanical specifications Material PA6-GF Color Black Remounting cycles (min.) 10 Permitted ambient conditions Ambient temperature • During operation -25 ℃ ... +85 ℃ • During storage -40 °C ... +100 °C Design, dimensions and weight Dimensions (W x H x D) 19 x 27.5 x 18 mm Weight Approx. 2 g Type of mounting Cylinder head screw M4 Tightening torque at room temperature ≤ 0.5 Nm

C79000-G8976-C492-01, 12/2017 5 6 Dimensional drawings Dimension drawing of transponder corner bracket for MDS D160, D460 and D560 All dimensions in mm Transponder corner bracket for MDS D160, D460 and D560 C79000-G8976-C492, 12/2017 Trademarks All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner. Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions. Siemens AG Division Process Industries and Drives Postfach 48 48 90026 NÜRNBERG GERMANY