ORQA FPV.ONE Operation & User’s Manual

FPV.ONE User Manual Rev. 1.6 | September 2020. Orqa FPV.ONE User Manual, Rev.1.6 ©2020. Orqa Ltd. ...

PACKAGE CONTENTS 3 CONTROLLING THE GOGGLES 7 NAVIGATING THE MENUS 8 RECEIVER SETTINGS 9 INPUT SOURCE 11 IMAGE SETTINGS 12 STAND BY 13 FEATURES 14 BATTERY 16 ABOUT 17 DVR 19 VIDEO PLAYBACK 23 BOOT SCREEN LOGO 25 CONNECTIONS PINOUT 26 ORQA ORIGINAL BATTERY 27 CHARGING THE BATTERY 28 TECHNICAL SPECIFICATIONS 29 2 Orqa FPV.ONE User Manual, Rev.1.6 ©2020. Orqa Ltd. ...

Power Button Press the Power Button to power the goggles On or Off . There are different power-on modes. Check page 13 for more information. Fan Button To prevent the lenses from fogging due to high humidity or sweat, use the defogging fan. Press the Fan Button to turn the fan on or off . Right-hand Joystick Use the Right-hand joystick for advanced playback functions. . Left-hand Joystick Use the Left-hand Joystick to access the main menu (default) . Both joysticks can be used for navigating the main menu or advanced playback functions (depending on which one is the main joystick Battery Check Press the Battery Check Button to s ...

There are two main menus that are accessible via the two corresponding joysticks on the top side of the goggles. The Left-hand joystick controls the main menu. The main menu incorporates all the main controls and goggles settings. The main control joystick can be chosen in the “BUTTON OPTIONS” menu. The Right-hand joystick is mainly used for playback settings or to control the main menu which is used mainly to adjust the Digital Video Recorder and Video Playback settings. To enter the main or additional menu simply press the corresponding joystick. Once inside the menu move the corresponding joystick up, down, left or right in ...

the main receiver module bay. In order to control the different receiver modules directly from the goggles, it is important to select the receiver module that you are using. Also, by selecting the correct module the goggle’s OSD and module’s OSD will work together without conflicting with each other. For example, if RapidFire is selected, you will be able to change the channel by short pressing the CHANNEL UP or CHANNEL DOWN buttons on the goggles. A long press on the CHANNEL UP or CHANNEL DOWN buttons changes the band on the receiver module. This featur ...

desired frequency of the RapidFire receiver module. Please note that RapidFire firmware must be updated to at least version 1.3. to have the full functionallity with the Orqa goggles. 10 Orqa FPV.ONE User Manual, Rev.1.6 ©2020. Orqa Ltd. ...

You can select between: Receiver, HDMI, AV in and AUTOMATIC. AUTOMATIC setting will bring up the image from the input you feed to the goggles. When automatic mode is on, the default setting is Receiver, but as soon as you plug in another source it will automatically switch to that input. If an HDMI source with an unsupported signal is connected, the “Unsupported HDMI Input” message will appear on-screen. Automatic setting priority 1. HDMI 2. AV in 3. RX 11 Orqa FPV.ONE User Manual, Rev.1.6 ©2020. Orqa Ltd. ...

and Supersize. You can access the image settings via the user menu to fine-tune the image. When adjusting Contrast, Brightness, and Color, you will see a little image in the right corner of OSD where you can track your settings while changing them. There you can change the setting between 0 and 100 by moving the main joystick ( or left and right. With the ASPECT RATIO setting you can choose between the 16:9 and 4:3 image ratio. Adjust this setting to best fit your image source. SUPER SIZE, due to large FOV some of the users can experience pincushion distortion ...

When the Stand-By mode is activated the goggles will go into the stand-by when they are taken off the head. In order to have the Stand-by mode function properly make sure that the stand-by sensor is not obstructed by the face pad foam. To activate the Stand-by mode set it to On. The goggles will enter the stand-by after the set delay time has passed. The default delay time setting is 20 seconds, and it can be adjusted in steps of 10 seconds to a maximum of 240 seconds. Once the goggles are put back on, they will automatically turn back on. Please note that the Stand ...

better overall user experience. The ​HEAD TRACKER feature uses goggles’ integrated IMU to track the movement of the pilots’ head. This feature requires the IMU to be reset every time this feature is used. This is achieved by scrolling to the "SET ZERO POINT" and by depressing the left-hand joystick . If the camera on the aircraft starts to drift (IMU was not calibrated), press the “​SET ZERO POINT​” again. For quick ZERO POINT setup, long press the Battery check button. The ​HEAD TILT ALARM is used to help the pilots aim the directional antenna. Especially l ...

on/off your goggles. There are 3 power-on modes: ▪ Mode 1: SINGLE PRESS ▪ Mode 2: ONE SHORT - ONE LONG PRESS ▪ Mode ALWAYS ON In the ALWAYS ON mode goggles are powered ON/OFF by plugging or unplugging the power source (battery) to the goggles. The sound feedback can be switched on or off with the ​BUTTON SOUND​. THE JOYSTICK SETTINGS You can choose from below joystick settings. ● you can invert joystick (swap up and down on joystick) ● you can switch the buttons sound on/off ● joystick-choose right or left joystick for main menu control ​QUICK IMAGE SETTINGS ON ...

status. The goggles can show the battery charge level on-screen and notify you when the battery voltage is low. There are a couple of options to set up how the battery information is displayed. In the Battery >Display menu you can choose whether the battery charge level is showed in “Volts” or in Percentage. In normal use, to display the battery status simply press the “Battery check” button. When battery voltage is below 6.1V, the goggles will safely shutdown. Additionally, you can choose where on the screen the battery info will be displayed. To adjust the position ...

goggles. To set up the ​Date/Time​ go into Date and Time sub-menu and change the settings. Once set, press the main joystick to save and exit this setting. Under the “Info” sub-menu you can find the firmware and hardware version, your goggles ID and uptime of your goggles. Firmware version shows the current firmware version installed on the goggles. Every time the firmware updates the info will be shown here. It will show the current version. Hardware version Hardware version shows the hardware (electronics) version of the goggles. This info is factory set and ca ...

the video and audio from any of the inputs. To use the DVR, the micro SD card must be inserted in the dedicated slot in the faceplate. Insert the micro SD card with the contacts facing up. Inserting the micro SD Card incorrectly ​m​ight result in getting the card stuck in the goggles. To start recording, press the “DVR Quick Record” button on the top side of the goggles. The button is marked with the red dot. DVR starts recording instantly from the input that is shown on the screen. During the DVR 19 Orqa FPV.ONE User Manual, Rev.1.6 ©2020. Orqa Ltd. ...

symbol is blinking in the top right corner of the screen. Note that DVR will not record any of the goggle’s OSD features which might be shown on screen during recording. OSD features generated by a receiver (e.g. RapidFire RSS bars) will be recorded.When recording, the DVR saves data onto the inserted micro SD card. Eventually, all the available memory space will be used and there will be no free space for the DVR to store the data. When there is no more available space on the micro SD card, the DVR will stop recording. In order to prevent the DVR from stopping the recording because of unavailable storage space, the “Auto Delete� ...