Newco Fresh Cup Manual 

NEWCO ENTERPRISES INC, 3650 NEW TOWN BLVD SAINT CHARLES, MO 63301 1-800-325-7867 FAX 1-636-925-0029 Features/ Specifications • AUTOMATIC POD REMOVAL • FLOWMETER OPTION • 20 OZ TRAVEL MUG • LARGE POD WASTE TRAY / THRU COUNTER OPTION • ADJUSTABLE DRINK STRENGTH • ADJUSTABLE DRINK VOLUME ...

SPECIFICATIONS ………………………………………………………………………………………….. 3 NEWCO PRODUCT WARRANTY ………………………………………………………………………... 4 MACHINE SET-UP …………………………………………………………………………………………. 5 MACHINE OPERATION ……………………………… ...

TANK CAPACITY-1 US GALLON DRIP TRAY CAPACITY 8 OUNCES POD WASTE TRAY CAPACITY 80 PODS-USE WASTE TRAY PN 780306 FOR THRU-COUNTER USE UP TO 20 OZ CUP SIZE SHIPPING WT-APPROX 35 LBS ...

Newco warrants equipment manufactured by it for 1 Year Parts & Labor These warranty periods run from the date of installation Newco warrants that the equipment manufactured by it will be commercially free of defects in material and workmanship existing at the time of manufacture and appearing within the applicable warranty period. This warranty does not apply to any equipment, component or part that was not manufactured by Newco or ...

and lifting machine. LIFT MACHINE FROM MACHINE BOTTOM ONLY. DO NOT MOVE MACHINE UNLESS THE HOT WATER TANK IS DRAINED AND EMPTY. 1. Open and install the drip tray grill and place drip tray into pod tray 2. Connect water fitting with strainer on the rear of machine under the power switch. Plumber's Installation Instructions 1) Brewer must be installed to ...

STRENGTH OR CUP SIZE, TEA, ETC PUSH & HOLD FOR HOT WATER DISPENSE WHEN DRAWER IS CLOSED PUSH TO RETURN BREW MECHANISM TO HOME POSITION WHEN DRAWER IS OPEN • TEMPERATURE RANGE IS 170-203 DEGREES • POWER SAVE OR POWER FEATURE AVAILABLE • BEEPER VOLUME CAN BE ADJUSTED OR BEEPER CAN BE SHUT OFF • AIR PUMP POD DRYING TIME & PUMP ST ...

MACHINES EQUIPPED WITH A FLOWMETER- Please run your Fresh Cup pod brewer a few times. If the volume dispensed is comparable to the amount expected from your Button Settings (which are set in the programming menu as described BELOW) and consistent and the pulsing is acting as expected you are done. However, if your dispensed calibration volume is larger or smaller than the volume setting for each brew button, then adjus ...

TEMPERATURE: In this entry the user may set the tank temperature in the range of 170 to 205 degrees Fahrenheit with the default at 200 degrees F. Pressing button D (see Fig 1) will toggle the display so the user may view the real tank temperature. The real temperature display has all three decimal points illuminated. Pressing button D (see Fig 1) again will switch the display back to show the current set point. As wit ...

CALIBRATION*: (NON-FLOWMETER MACHINES ONLY) This entry shows the amount of water the brewer dispenses in 30 seconds with no pauses. To run calibration, place a container able to hold at least 10 oz preferably greater. Press button D (see Fig 1) and the brewer will enter a brew cycle. The door will open to allow the user to place a beverage pod in the drawer. After the pod has been placed press the button D button (see ...

entries that can be scanned through, backward and forward, using button A and button B (see Fig 1). The letter to the right of the button is the buttons letter assignment. To enter the maintenance menu, hold Button A (Open) and the Reset key (Hot Water) down while turning on the Fresh Cup machine. Hold the keys down until the Drain Line message appears ...

REMOVE BRASS KNURLED NUTS (2) LOOSEN ACORN NUTS (4) DRAINING THE HOT WATER TANK THE DRAIN TUBE IS CLIPPED TO THE TANK PLATE IN FRONT OF THE TANK. THE HOT WATER TANK CAN BE DRAINED FROM THE FRONT OF THE MACHINE – UNPLUG MACHINE FROM POWER SOURCE. REMOVE POD WASTE TRAY. CAUTION-UNLESS THE TANK IS LEFT TO COOL THE WATER IS EXTREMELY HOT AND CAN CUASE HARMFUL BURNS. REPLACE DRAIN PLUG, ENS ...

LOOSEN BUT DO NOT REMOVE THESE 2 SCREWS THEN LIFT & PULL CONTROL BOARD & BRACKET OUT OF MACHINE TO ACCESS TRANSFORMER REMOVE (3) 8-32 NUTS TO PREPARE TANK FOR REMOVAL (TWO ON TOP OF TANK & ONE ON BOTTOM OF PUMP BRACKET REMOVE (2) 6-32 SCREWS TO REMOVE SIDE PANEL FOR PUMP ACCESS (REMOVE TOP COVER BEFORE REMOVING SIDE PANELS) LOOSEN SCREWS TO REMOVE TOP & BACK COVERS ...

*MACHINE IS ORDERED FOR 56MM OR 61MM POD SIZE ITEM # NEWCO PN DESCRIPTION QTY/EA 1 780230 BREW MECH MOTOR 2 2 780231 DELTROL SOLENOID 1 3 780257 780329 UPPER BREW CHAMBER-61MM UPPER BREW CHAMBER-56MM 1 4 773246 U-CUP SEAL RING 1 5 780262 780314 LOWER BREW CHAMBER-61MM LOWER BREW CHAMBER-56MM 1 6 780418 EJECT SLOPE CAM ASS’Y 1 ...

ITEM # NEWCO PN DESCRIPTION QTY/EA 1 110958 RELAY, 12 VDC SPST 30A 1 2 111593 HI-LIMIT THERMOSTAT 1 3 706341 PUMP ASS’Y-120 VOLT 1 4 781772 PUMP ASS’Y W/ELBOW 1 5 780253 PUNCHED TANK W/STUD 1 6 773056 AIR PUMP, POD 1 7 108022 LIQUID LEVEL PROBE 1 8 151677 DUAL TEMP THERM PROBE 1 9 110051 ELBOW ¼ TUBE X 1/8 NPT 1 10 704166-10 TANK HEATING ELEMENT 1 ...

ITEM # NEWCO PN DESCRIPTION QTY/EA 1 780225 CONTROL BOARD 1 2 110626 SWITCH, DPST, ON/OFF 1 3 102383 SOLENOID FILL VALVE 1 4 105115 TRANSFORMER 120VAC-24VAC 1 5 780224 DISPLAY BOARD 1 ERROR MESSAGES Message - "THERMISTOR ERROR" THERMISTOR IS OPEN OR SHORTED-REPLACE PN 151677 Message - "HIGH TEMP ERROR" RAPID TEMPERATURE RISE-HEATER ON WITH LOW WATER LEVEL- CHECK FILL VALVE OR WATER SUPPLY LINE Message - "UPPER/LOWER MOTOR ...

VIEW FROM TOP OF MACHINE COVER REMOVED ONLY USED FOR ADJUSTING WATER FLOW RATE (FACTORY SET) CALIBRATION PUMP FLOW ADJUSTMENT CLOCKWISE DECREASE FLOW COUNTER CLOCKWISE INCREASE FLOW ...

+ - - + 2 1 4 3 COFFEE PUMP FILL SOLENOID BK/WH BK/WH BR BK WH BR YL VIO/BK VIO/WH VIO/BK VIO/BK BK BK BK BK VIO/BK VIO/BK WH WH ...